Hi Leute,
bei meiner DB800 mit dem Image Open ATV 4.2 hatte ich gestern ein
Software-Update gemacht. Beim erforderlichen Neustart der Box blieb
diese hängen; nichts half mehr. Also habe ich das Image neu geflashed,
in der Hoffnung das System mit der vor 3 Tagen gemachten kompletten
Sicherung (dflash) wieder auf den alten Stand bringen zu können. Aber
das Flashen half nichts. Auch mehrfaches neues Flashen mit unterschiedlichsten Images per Webbrowser und Dreamup halfen nichts. Zwischenzeitlich bootet die Box auch nicht mehr
bis zum Image. Anbei der Bootlog. Was läuft hier schief? Irgendwas mit DHCP?
Diff
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.01(0x133/high) {BO23456}
2ND STAGE OK, build #84 (2011-09-02)
0.000 - BCM board setup
0.002 - fp init
0.003 - ca init
0.719 - load config
0.747 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #84
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /boot/bootlogo-dm800.elf.gz
bootlogo size: 285065
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@sail
lard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-2.6.18-7.4-dm800.gz
<5>Linux version 2.6.18-7.4-dm800 (oe1@build3) (gcc version 4.9.1 (GCC) ) #1 Fri
May 8 00:05:01 CEST 2015
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null quiet
2 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttyS0,115200 ip=dhcp root=/dev/nfs rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, lines
ize 16 bytes.
[4294667.296000] Primary data cache 32kB, 2-way, linesize 16 bytes.
[4294667.296000] Synthesized TLB refill handler (20 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (31 instructions).
[4294667.296000] timer irq 67 end 57
[4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[4294667.296000] Found MIPS counter frequency: 149 Mhz
[4294667.296000] Using 148.501 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.296000] ################## brcm_serial_console_init, sercon=8037b00c
[4294667.369000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[4294667.378000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[4294667.412000] Memory: 145152k/262144k available (3125k kernel code, 116888k r
eserved, 646k data, 128k init, 0k highmem)
[4294667.445000] Mount-cache hash table entries: 512
[4294667.450000] Checking for 'wait' instruction... available.
[4294667.460000] NET: Registered protocol family 16
[4294667.466000] registering PCI controller with io_map_base unset
[4294667.472000] registering PCI controller with io_map_base unset
[4294667.480000] SCSI subsystem initialized
[4294667.484000] usbcore: registered new driver usbfs
[4294667.489000] usbcore: registered new driver hub
[4294667.495000] SATA: Primary Bus Master Status Register offset = b0520000 + 00
000300 = b0520300
[4294667.504000] SATA: before init Primary Bus Master Status reg = 0x00000000.
[4294667.511000] SATA: after init Primary Bus Master Status reg = 0x00000020.
[4294667.520000] NET: Registered protocol family 2
[4294667.534000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[4294667.542000] TCP established hash table entries: 8192 (order: 3, 32768 bytes
)
[4294667.550000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[4294667.557000] TCP: Hash tables configured (established 8192 bind 4096)
[4294667.563000] TCP reno registered
[4294667.571000] JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
[4294667.579000] SGI XFS with large block numbers, no debug enabled
[4294667.586000] Initializing Cryptographic API
[4294667.590000] io scheduler noop registered
[4294667.595000] io scheduler anticipatory registered (default)
[4294667.600000] io scheduler deadline registered
[4294667.605000] io scheduler cfq registered
[4294667.618000] Broadcom serial driver version 1.00 (2000-11-09) with SERIAL_PC
I enabled
[4294667.638000] loop: loaded (max 8 devices)
[4294667.643000] Broadcom BCM7401 P31 Ethernet Network Device v2.0 May 8 2015 0
0:04:38
[4294667.651000] SUNDRY revision = 74010021, have IP Hdr Opt=1
[4294667.663000] Config Internal PHY Through MDIO: Auto-negotiation timed-out
[4294669.742000] : 10 MB Half-Duplex (assumed)
[4294669.752000] ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB
0510030 irq 42
[4294669.760000] scsi0 : sata_svw
[4294670.071000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F0000)
[4294670.087000] ata1.00: ATA-8, max UDMA/133, 976773168 sectors: LBA48 NCQ (dep
th 0/32)
[4294670.105000] ata1.00: configured for UDMA/133
[4294670.111000] Vendor: ATA Model: SAMSUNG HM500JI Rev: 2AC1
[4294670.117000] Type: Direct-Access ANSI SCSI revision
: 05
[4294670.126000] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[4294670.133000] sda: Write Protect is off
[4294670.137000] SCSI device sda: drive cache: write back
[4294670.143000] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[4294670.150000] sda: Write Protect is off
[4294670.155000] SCSI device sda: drive cache: write back
[4294670.160000] sda: sda1
[4294670.194000] sd 0:0:0:0: Attached scsi disk sda
[4294670.199000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294670.205000] Broadcom STB NAND controller (BrcmNand Controller)
[4294670.212000] B4: NandSelect=40000002, nandConfig=04042300, chipSelect=1
[4294670.219000] brcmnand_probe: CS1: dev_id=ad76ad76
[4294670.224000] After: NandSelect=40000002, nandConfig=04042300
[4294670.230000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase
_shift=e
[4294670.238000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[4294670.244000] timing1 not adjusted: 5363444f
[4294670.249000] timing2 not adjusted: 00000fc6
[4294670.253000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB
[4294670.259000]
[4294670.259000] Found NAND: ACC=e3000000, cfg=04042300, flashId=ad76ad76, tim1=
5363444f, tim2=00000fc6
[4294670.270000] BrcmNAND version = 0x0001 64MB @00000000
[4294670.276000] Found NAND chip on Chip Select 1, chipSize=64MB, usable size=64
MB, base=14000000
[4294670.284000] ACC_CONTROL B4: e3000000
[4294670.288000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shi
ft=14
[4294670.296000] Brcm NAND controller version = 0.1 NAND flash size 64MB @140000
00
[4294670.303000] mtd->oobsize=16, mtd->eccOobSize=16
[4294670.308000] brcmnand_scan: mtd->oobsize=16
[4294670.313000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[4294670.319000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel
=15, eccbytes=3
[4294670.328000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[4294670.335000] brcmnandCET: Status -> Deferred
[4294670.340000] numchips=1, size=4000000
[4294670.344000] Creating 4 MTD partitions on "bcm7xxx-nand.0":
[4294670.349000] 0x0000000000000000-0x0000000004000000 : "complete"
[4294670.359000] 0x0000000000000000-0x0000000000040000 : "loader"
[4294670.366000] 0x0000000000040000-0x0000000000400000 : "boot partition"
[4294670.373000] 0x0000000000400000-0x0000000004000000 : "root partition"
[4294670.383000] ehci_hcd_brcm_init: Initializing 1 EHCI controller(s)
[4294670.390000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (E
HCI-brcm-0)
[4294670.398000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294670.405000] - USB h/w setup mode <B>
[4294670.405000] - USB power enable set for active LOW mode
[4294670.415000] brcm-ehci brcm-ehci.0: BRCM EHCI
[4294670.420000] brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus num
ber 1
[4294670.428000] brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
[4294670.434000] brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 De
c 2004
[4294670.443000] usb usb1: configuration #1 chosen from 1 choice
[4294670.449000] hub 1-0:1.0: USB hub found
[4294670.453000] hub 1-0:1.0: 2 ports detected
[4294670.558000] ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
[4294670.565000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHC
I-brcm-0)
[4294670.573000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.580000] - Resetting at b0480408
[4294670.584000] <-- brcm_start_hc
[4294670.587000] brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
[4294670.592000] brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus
number 2
[4294670.601000] brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
[4294670.662000] usb usb2: configuration #1 chosen from 1 choice
[4294670.668000] hub 2-0:1.0: USB hub found
[4294670.673000] hub 2-0:1.0: 2 ports detected
[4294670.778000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHC
I-brcm-1)
[4294670.787000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.794000] - Resetting at b0480508
[4294670.798000] <-- brcm_start_hc
[4294670.801000] brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
[4294670.806000] brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus
number 3
[4294670.814000] brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480500
[4294670.876000] usb usb3: configuration #1 chosen from 1 choice
[4294670.882000] hub 3-0:1.0: USB hub found
[4294670.886000] hub 3-0:1.0: 2 ports detected
[4294670.992000] Initializing USB Mass Storage driver...
[4294670.998000] usbcore: registered new driver usb-storage
[4294671.003000] USB Mass Storage support registered.
[4294671.008000] i2c /dev entries driver
[4294671.012000] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu
Jun 22 13:55:50 2006 UTC).
[4294671.022000] ALSA device list:
[4294671.025000] No soundcards found.
[4294671.029000] TCP bic registered
[4294671.032000] NET: Registered protocol family 1
[4294671.037000] NET: Registered protocol family 17
[4294672.545000] Sending DHCP requests ...... timed out!
[4294762.452000] IP-Config: Reopening network devices...
[4294763.959000] Sending DHCP requests ...
Alles anzeigen