DM 800 HD se Bootet nur bis " 192.168.2.105
dream box zeigte die eine Fehlermeldung und ganz unten stand "Reboot in 10 sec."
kein flashen über Ethernet oder mini USB möglich.
Was kann ich da noch tun? bin echt ratlos.
Freue mich über jede Hilfe.
DM 800 HD se Bootet nur bis " 192.168.2.105
dream box zeigte die eine Fehlermeldung und ganz unten stand "Reboot in 10 sec."
kein flashen über Ethernet oder mini USB möglich.
Was kann ich da noch tun? bin echt ratlos.
Freue mich über jede Hilfe.
Du könntest ein Bootlog erstellen und ins Forum stellen...
WIE ???
WIE ???
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.01.13 23:29:32 =~=~=~=~=~=~=~=~=~=~=~=
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=00000012
RC2=00000018
WC2=00000036
RC3=0000000E
WC3=FFFFFFEE
RC4=0000000E
WC4=00000037
NWC=00000012
RC5=00000006
WC5=00000012
RC6=00000018
WC6=00000012
NRC=0000000F
RW=00000013
WW=0000004A
G=00000000 R=0000000F W=00000012
BL=00000000
RC1=00000002
RC2=00000015
BL=00000001
RC1=00000002
RC2=00000018
BL=00000002
RC1=00000006
RC2=00000014
BL=00000003
RC1=00000007
RC2=00000018
BL=00000004
RC1=00000006
RC2=00000014
BL=00000005
RC1=00000004
RC2=00000018
BL=00000006
RC1=00000005
RC2=00000019
BL=00000007
RC1=00000009
RC2=00000019
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox D M800SE
FIRST STAGE 1.0/400 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-01)
0.000 - BCM board setup
0.000 - fp init
0.000 - ca init
0.520 - load config
0.546 - config loaded.
* press [S] to enter setup
OLED found!
color oled reset
lcd: BOOT #84
P23 detected!
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . | / - \ | / - \ | / - \ done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 315426
Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K !PAL_I !PAL_M !PAL_N !PAL_NC !PAL_60 !SECAM_L !SECAM_B !SECAM_G !SECAM_D !SECAM_K !SECAM_H 1080i 720p 480p 1080i_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p !DVI_640x480p_CVT !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_Red !DVI_640x480p_66Hz !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_640x480p_85Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz
best supported mode is 25
using 1920x1080i (50.00 Hz)
HDMI
using colorspace: 1
create surface 1920 1080
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
executing '/flash/vmlinux.gz' returned: -2
waiting for link...
waiting for DHCP...
no server address given
using dhcp address
no tftp server address was specified, neither manually nor via dhcp. aborting tftp.
lcd: /boot/zImage.elf
find_inode failed for name=zImage.elf
load: Failed to find inode
no valid boot source found. press any key to enter setup.
lcd: *** STOP ***
was heisst denn kein flashen möglich?
Also die Box steht da im sog. STOP Mode weil das dateisystem / image wohl kaputt ist. Der 2nd stage loader ist aber vorhanden.
Wenn du einen DHCP Server im netz hättest könntest Du die Box einfach flashen über die IP die sie dann vom DHCP bekommt.
Ansonsten kannst Du die Box nur mit dreamup flashen.
Beides sollte aber funktionieren.