DM 800 HD se Bootet nur bis " 192.168.2.105

  • DM 800 HD se Bootet nur bis " 192.168.2.105
    dream box zeigte die eine Fehlermeldung und ganz unten stand "Reboot in 10 sec."
    kein flashen über Ethernet oder mini USB möglich.


    Was kann ich da noch tun? bin echt ratlos.
    Freue mich über jede Hilfe.

  • Du könntest ein Bootlog erstellen und ins Forum stellen...

  • WIE ???


    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.01.13 23:29:32 =~=~=~=~=~=~=~=~=~=~=~=


    BCM74130011
    012
    K1
    K2


    K3


    K4


    K5


    Shmoo Version=3.8
    DDR Freq=0x0000018C
    %00000001%
    RC1=00000005
    WC1=00000012
    RC2=00000018
    WC2=00000036
    RC3=0000000E
    WC3=FFFFFFEE
    RC4=0000000E
    WC4=00000037
    NWC=00000012
    RC5=00000006
    WC5=00000012
    RC6=00000018
    WC6=00000012
    NRC=0000000F
    RW=00000013
    WW=0000004A
    G=00000000 R=0000000F W=00000012
    BL=00000000
    RC1=00000002
    RC2=00000015


    BL=00000001
    RC1=00000002
    RC2=00000018


    BL=00000002
    RC1=00000006
    RC2=00000014


    BL=00000003
    RC1=00000007
    RC2=00000018


    BL=00000004
    RC1=00000006
    RC2=00000014


    BL=00000005
    RC1=00000004
    RC2=00000018


    BL=00000006
    RC1=00000005
    RC2=00000019


    BL=00000007
    RC1=00000009
    RC2=00000019
    3
    COPY CODE
    COMPARE CODE
    4567
    (c) 2007,2008 Dream Multimedia GmbH. All rights reserved.


    Dreambox D M800SE


    FIRST STAGE 1.0/400 {BO23456}
    [m


    2ND STAGE OK, build #84 (2011-09-01)


    0.000 - BCM board setup
    0.000 - fp init
    0.000 - ca init
    0.520 - load config
    0.546 - config loaded.
    * press [S] to enter setup
    OLED found!
    color oled reset
    lcd: BOOT #84
    P23 detected!
    - read config file: /boot/secondstage.conf
    detected jffs2 blocksize: 16kb
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    ++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
    dreamupd initialized
    Scanning JFFS2 FS: . | / - \ | / - \ | / - \ done.


    find_inode failed for name=secondstage.conf


    load: Failed to find inode


    - failed to open /boot/secondstage.conf
    - failed to open /cf/autorun.bat
    lcd: /flash/bootlogo.elf
    bootlogo size: 315426
    Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K !PAL_I !PAL_M !PAL_N !PAL_NC !PAL_60 !SECAM_L !SECAM_B !SECAM_G !SECAM_D !SECAM_K !SECAM_H 1080i 720p 480p 1080i_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p !DVI_640x480p_CVT !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_Red !DVI_640x480p_66Hz !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_640x480p_85Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz
    best supported mode is 25
    using 1920x1080i (50.00 Hz)
    HDMI
    using colorspace: 1
    create surface 1920 1080
    Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
    parsing JPEG header..
    Virtual FB Size: 1280x720
    lcd: /flash/vmlinux.gz
    executing '/flash/vmlinux.gz' returned: -2
    waiting for link...
    waiting for DHCP...
    no server address given
    using dhcp address
    no tftp server address was specified, neither manually nor via dhcp. aborting tftp.
    lcd: /boot/zImage.elf
    find_inode failed for name=zImage.elf


    load: Failed to find inode


    no valid boot source found. press any key to enter setup.
    lcd: *** STOP ***

    • Offizieller Beitrag

    was heisst denn kein flashen möglich?


    Also die Box steht da im sog. STOP Mode weil das dateisystem / image wohl kaputt ist. Der 2nd stage loader ist aber vorhanden.


    Wenn du einen DHCP Server im netz hättest könntest Du die Box einfach flashen über die IP die sie dann vom DHCP bekommt.


    Ansonsten kannst Du die Box nur mit dreamup flashen.


    Beides sollte aber funktionieren.