Hallo
Habe mit den OE1.6er-Images von der CF-Karte bei der „7025+“ Boot-Probleme
Mit den OE1.5er-Images gibt es da keine Probleme, da funktioniert alles.
Entpacke die Images immer wie folgt auf die CF-Karte,
Die CF-Karte Formatiere ich wie folgt:
Partition 1 mit FAT worauf der Inhalt des Boot-Ordners des Images kommt.
Partition 2 mit ext2 worauf der Inhalt aller anderen Ordner und Dateien des Images
kommen.
Die autorun.bat sieht wie folgt aus:
/cf/bootlogo.elf
/cf/vmlinux.gz console=ttyS0,115200 root=/dev/hdc5 rootfstype=ext2 rw rootdelay=0
Die fstab sieht wie folgt aus:
rootfs / auto defaults 1 1
proc /proc proc defaults 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
usbdevfs /proc/bus/usb usbfs defaults 0 0
/dev/root / auto ro 0 0
tmpfs /var tmpfs defaults 0 0
tmpfs /tmp tmpfs defaults 0 0
/dev/ide/host1/bus0/target0/lun0/part1 /boot vfat defaults 0 0
/dev/ide/host1/bus0/target0/lun0/part5 /media/hdc5 auto defaults 0 0
/dev/ide/host0/bus0/target0/lun0/part1 /media/hdd auto defaults 0 0
damit Bootet das OE1.5er auch Super durch.
Nur das OE1.6 bleibt Hängen. (release-dm7025-3.0.0.nfi)
Hier das Logg:
Dreambox DM7025
FIRST STAGE 1.4 {2345}
2ND STAGE OK, build #76 (20091202)
0.000 - DM7025 board setup
0.002 - initializing PCI...
0.012 - done!
0.013 - fp init
FP version 7 detected
0.136 - ca init
RSA key 1 is used.
0.240 - load config
0.820 - config loaded.
* press to enter setup
1957536 sectors (955 MB)
P 06 63 1060227 < 1957536
OLED found!
BOOT #76(20091202)
CF AVAILABLE
+CF
Device 2: Partition 1: Filesystem: FAT16 "AKTIV "
/cf/bootlogo.elf
vscale: 576:576
/cf/vmlinux.gz
dreamupd initialized
LINUX started...
ATI Xilleon 226 (little endian), Solo mode
PCI bus speed is 33MHz
Initializing IRQs
about to enable interrupts!
interrupts enabled.
Linux version 2.6.12.6 (tmbinc@pepe.multimedia-labs.de) (gcc version 4.4.3 (GCC)
) #1 Thu Nov 11 18:31:29 UTC 2010
memsize: 77MB
Xilleon REG value before setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
Xilleon REG value after setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
CPU revision is: 00018448
Determined physical RAM map:
memory: 00080000 @ 00000000 (ROM data)
memory: 00080000 @ 00080000 (reserved)
memory: 04c00000 @ 00100000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/hdc5 rootfstype=ext2 rw root
delay=0
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 8192 bytes)
calculating r4koff... CPU frequency 299.68 MHz
Using 149.838 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 73088k/77824k available (2771k kernel code, 4588k reserved, 792k data, 1
24k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
Can't analyze prologue code at 803b2d20
PCI init - ohwe, ohwe..
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
irq fixup slot 10 vendor 10ec irq 33
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
inotify device minor=63
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 100) is a 16550A
ttyS1 at MMIO 0x0 (irq = 99) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
8139too Fast Ethernet driver 0.9.27
RTL8139 EEPROM CONTENT: 8129 10ec 8139 10ec 8139 2020 e512 0900 0034 0000
eth0: RealTek RTL8139 at 0x2000, 00:09:34:1c:17:12, IRQ 33
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
X226: IDE controller at PCI slot 0000:00:14.1
X226: chipset revision 1
X226: 100% native mode on irq 3
hwif->channel: 0, hwif->index: 0
ide0: BM-DMA at 0x2400-0x2407, BIOS settings: hda:DMA, hdb:DMA
init_hwif_xilleon, 0, mate: 00000000
hwif->channel: 0, hwif->index: 1
ide1: BM-DMA at 0x2400-0x2407, BIOS settings: hdc:DMA, hdd:DMA
init_hwif_xilleon, 1, mate: 804b20b8
select 1
hdc: TRANSCEND, ATA DISK drive
hdc: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdc: set_drive_speed_status: error=0x04 { DriveStatusError }
ide1 at 0x2410-0x2417,0x2422 on irq 3
select 0
hda: SAMSUNG HM160HC, ATA DISK drive
ide0 at 0x2410-0x2417,0x2422 on irq 3 (shared with ide1)
hdc: max request size: 128KiB
hdc: 1957536 sectors (1002 MB) w/1KiB Cache, CHS=1942/16/63
hdc: cache flushes not supported
/dev/ide/host1/bus0/target0/lun0:select 1
p1 p2 < p5 p6 >
hda: max request size: 1024KiB
select 0
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, (U)DMA
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1
adding dm7025 NAND !
2881 kb/s
6535 kb/s
- NAND PROBE: ad 75 ad 75
NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Unknown NAND 32MiB 3,3V 8-bit
)
Scanning device for bad blocks
Creating 4 MTD partitions on "NAND 32MiB 3,3V 8-bit":
0x00000000-0x02000000 : "complete"
0x00000000-0x00040000 : "loader"
0x00040000-0x00400000 : "boot partition"
0x00400000-0x02000000 : "root partition"
usbmon: debugs is not available
ohci_hcd 0000:00:14.2: PCI device 1002:4867 (ATI Technologies Inc)
ohci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:14.2: irq 2, io mem 0x10000000
usb usb1: Product: PCI device 1002:4867 (ATI Technologies Inc)
usb usb1: Manufacturer: Linux 2.6.12.6 ohci_hcd
usb usb1: SerialNumber: 0000:00:14.2
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24 10:33:39
2005 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Cannot open root device "hdc5" or unknown-block(22,5)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(22,5)
Wäre über jegliche Hilfe Dankbar
Mit freundlichen Grüßen
Norbert