Boxtyp:7020si
Hallo,
Ich habe gestern meine neue Dreambox 7020 Si bekommen und sie funktioniert ohne Harddisk perfekt.
Das Image ist Orginal von DMM !
Wenn ich nun eine HDD 3,5" 160 GB anstecke bootet die Box erst nach ca 8 min mit folgenden Fehler !
Bootlog:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
IBM STB04xxx OCP IDE driver version 2.3
hda: SAMSUNG SP1614N, ATA DISK drive
Using deadline io scheduler
ide0 at 0xc50541f8-0xc50541ff,0xc50541f6 on irq 25
initializing!
hda: max request size: 1024KiB
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(66)
hda: lost interrupt
/dev/ide/host0/bus0/target0/lun0:<4>hda: DMA timeout error
hda: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Unknown NAND 32MiB 3,3V 8-bit)
Scanning device for bad blocks
Nun könnte es ja sein das diese Harddisk defekt ist,deshalb habe ich meine von dem NAS (NSLU) genommen,die hat 3 partitionen und ist mit ext3 formatiert.
Aber auch mit dieser Harddisk bootet die DMM nun überhaupt nicht mehr.
Bootlog:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
IBM STB04xxx OCP IDE driver version 2.3
hda: ST3250824A, ATA DISK drive
Using deadline io scheduler
ide0 at 0xc50541f8-0xc50541ff,0xc50541f6 on irq 25
initializing!
hda: max request size: 1024KiB
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(66)
hda: lost interrupt
/dev/ide/host0/bus0/target0/lun0:<4>hda: DMA timeout error
hda: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
p1 p2 p3
hda: lost interrupt
NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Unknown NAND 32MiB 3,3V 8-bit)
Scanning device for bad blocks.....
.......
.......
.......
da: DMA timeout error
hda: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hda: lost interrupt
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
hda: lost interrupt
hda: DMA timeout error
hda: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hda: lost interrupt
hda: lost interrupt
hda: DMA timeout error
hda: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
Bevor ich nun meine NAS Harddisk neu Formatiere und alle daten darauf verliere wollte ich nur nachfragen woran es liegen kann. Filesystem,Größe der HDD,Jumper falsch > Master oder Slave, oder was könnte ich noch machen ?????
mit bitte um Hilfe
lg Rar