Hallo,
meine gerade neu erstandene DM 500 HD blinkt direkt nach dem ersten Einschalten rot, der Bildschirm zeigt kurz ein farbsattes Bild der DM 500, dann ein hell hinterlegtes, in der oberen linken Ecke erscheinen regelmäßig kurz zwei Zahnräder.
Fernbedienung funktioniert nicht.
Per Netzwerk kann man mit telnet auf die Box (die via DHCP eine Adresse nimmt), allerdings läuft kein httpd o.ä. Reboot über Netz bringt das gleiche Ergebnis.
Gibt es eine Möglichkeit, hier was zu machen oder schicke ich die Box gleich wieder zurück?
Viele Grüße,
Jens.
Neue DM 500 HD blinkt nur rot
-
-
bootlog erstellen und hier posten
-
Hallo,
leider habe ich keine Ahnung, wie man so ein bootlog erstellt Auch mit Forensuche bin ich nur auf Anleitungen für die 7xxx-Serie gekommen, die so aber nicht funktionieren können.
Wäre nett, wenn mir jemand einen Link auf eine Anleitung geben könnte. Danke!
Viele Grüße,
Jens.
-
Es gibt auch noch eine Welt außerhalb des Forums
http://dream.reichholf.net/wiki/Howto:Bootlog
http://dreamscreencast.de/2011/05/dsc015-bootlog-erstellen/Im wesentlichen musst du nur gedanklich das serielle Nullmodem-Kabel durch Mini-USB-Kabel ersetzen. Denn am PC meldet sich die Box immernoch mit einem (virtuellen) COM-Port.
-
Hallo,
danke für die Links - die erste Seite hatte ich auch gefunden, aber wegen "Pfeil runter drücken" resigniert, weil die 500er ja nur einen Einschaltknopf hat... Jetzt hats aber geklappt, hier das Log.
Problem scheint die letzte Zeile "kernel panic" zu sein...
Für Anregungen bin ich dankbar!
Viele Grüße,
Jens.
---------------------
BCM74130011
012
K1
K2K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000004
WC1=FFFFFFEE
RC2=00000012
WC2=00000039
RC3=0000000B
WC3=FFFFFFEE
RC4=0000000B
WC4=00000039
NWC=00000013
RC5=00000004
WC5=00000013
RC6=00000012
WC6=00000013
NRC=0000000B
RW=0000000F
WW=0000004C
G=00000000 R=0000000B W=00000013
BL=00000000
RC1=00000002
RC2=00000013BL=00000001
RC1=00000005
RC2=00000018BL=00000002
RC1=00000002
RC2=00000012BL=00000003
RC1=00000006
RC2=00000015BL=00000004
RC1=00000000
RC2=00000010BL=00000005
RC1=00000003
RC2=00000016BL=00000006
RC1=00000004
RC2=00000016BL=00000007
RC1=00000007
RC2=00000019
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM500HDFIRST STAGE 1.2/400 {BO23456}
2ND STAGE OK, build #80 (20101014)
.
0.017 - BCM board setup
0.017 - fp init
0.018 - ca init
0.492 - load config
0.519 - config loaded.
* press to enter setup
no OLED found!
BOOT #80(20101014)
P23 detected!
- read config file: /flash/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . | / - \ | / - \ | / - \ | / done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /flash/secondstage.conf
- failed to open /cf/autorun.bat
/flash/bootlogo.elf
bootlogo size: 79448
2nd videomode is 254
2nd videomode 254 is invalid
Supported modes: 1080i 720p 480p 1080i_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_
640x480p DVI_800x600p DVI_1024x768p !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280
x720p_Red !DVI_1024x768p_66Hz !DVI_1024x768p_70Hz !DVI_1024x768p_72Hz !DVI_1024x
768p_75Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x
720p_85Hz
best supported mode is 25
using 1920x1080i (50.00 Hz)
HDMI
using colorspace: 1
create surface 1920 1080
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@sail
lard.org>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm500hd (tmbinc@pepe.multimedia-labs.de) (gcc versio
n 4.4.3 (GCC) ) #1 SMP Wed Dec 15 21:56:26 UTC 2010
Fetching vars from bootloader... none present, using defaults.
Detected 256 MB on MEMC0 (strap 0x22bc0010)
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=ttyS0,115200
2 831ffeb8 830279a8
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1
CPU revision is: 0002a044
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttyS0,115200 ip=dhcp root=/dev/mtdblock3 rw
[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, lines
ize 64 bytes.
[4294667.296000] Primary data cache 64kB, 4-way, linesize 64 bytes.
[4294667.296000] Synthesized TLB refill handler (23 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (37 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (37 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (36 instructions).
[4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[4294667.296000] Found MIPS counter frequency: 203 Mhz
[4294667.296000] Using 202.501 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.303000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[4294667.303000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[4294667.316000] Memory: 145408k/262144k available (2803k kernel code, 116616k r
eserved, 597k data, 140k init, 0k highmem)
[4294667.339000] Mount-cache hash table entries: 512
[4294667.340000] Checking for 'wait' instruction... available.
[4294667.340000] plat_prepare_cpus: ENABLING 2nd Thread...
[4294667.341000] TP0: prom_boot_secondary: Kick off 2nd CPU...
[4294667.343000] CPU revision is: 0002a044
[4294667.343000] FPU revision is: 00130001
[4294667.343000] Primary instruction cache 32kB, physically tagged, 2-way, lines
ize 64 bytes.
[4294667.343000] Primary data cache 64kB, 4-way, linesize 64 bytes.
[4294667.343000] Synthesized TLB refill handler (23 instructions).
[4294667.364000] Brought up 2 CPUs
[4294667.397000] migration_cost=1000
[4294667.400000] NET: Registered protocol family 16
[4294667.401000] registering PCI controller with io_map_base unset
[4294667.401000] registering PCI controller with io_map_base unset
[4294667.403000] SCSI subsystem initialized
[4294667.404000] usbcore: registered new driver usbfs
[4294667.405000] usbcore: registered new driver hub
[4294667.406000] NET: Registered protocol family 2
[4294667.419000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[4294667.420000] TCP established hash table entries: 8192 (order: 4, 65536 bytes
)
[4294667.421000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[4294667.422000] TCP: Hash tables configured (established 8192 bind 4096)
[4294667.423000] TCP reno registered
[4294667.423000] brcm-pm: disabling power to USB block
[4294667.424000] brcm-pm: disabling power to ENET block
[4294667.425000] brcm-pm: disabling power to SATA block
[4294667.428000] JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc
.
[4294667.429000] Initializing Cryptographic API
[4294667.430000] io scheduler noop registered
[4294667.430000] io scheduler anticipatory registered
[4294667.431000] io scheduler deadline registered
[4294667.432000] io scheduler cfq registered (default)
[4294667.436000] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharin
g disabled
ÿ[4294667.437000] serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
[4294667.438000] serial8250: ttyS1 at MMIO 0x0 (irq = 67) is a 16550A
[4294667.439000] brcm-pm: enabling power to ENET block
[4294667.440000] Broadcom BCM7413 P21 Ethernet Network Device v2.0 Dec 15 2010 2
1:55:45
[4294667.442000] Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg)
[4294669.082000] brcm-pm: enabling power to SATA block
[4294669.099000] ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB
0510030 irq 42
[4294669.100000] ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB
0510130 irq 42
[4294669.101000] scsi0 : sata_svw
[4294669.405000] ata1: SATA link down (SStatus 4 SControl 300)
[4294669.437000] ATA: abnormal status 0x7F on port 0xb051001c
[4294669.437000] scsi1 : sata_svw
[4294669.741000] ata2: SATA link down (SStatus 4 SControl 300)
[4294669.773000] ATA: abnormal status 0x7F on port 0xb051011c
[4294669.773000] Broadcom STB NAND controller (BrcmNand Controller)
[4294669.774000] NAND_CS_NAND_XOR=00000000
[4294669.775000] brcmnand_probe: CS0: dev_id=ad76ad76
[4294669.775000] After: NandSelect=40000002, nandConfig=04042300
[4294669.776000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase
_shift=e
[4294669.777000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[4294669.778000] timing1 not adjusted: 5363444f
[4294669.778000] timing2 not adjusted: 00000fc6
[4294669.779000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB
[4294669.780000]
[4294669.780000] Found NAND: ACC=00000010, cfg=04042300, flashId=ad76ad76, tim1=
5363444f, tim2=00000fc6
[4294669.781000] BrcmNAND version = 0x0302 64MB @00000000
[4294669.782000] B4: NandSelect=40000002, nandConfig=04042300, chipSelect=-1
[4294669.782000] brcmnand_probe: CS-1: dev_id=ad76ad76
[4294669.783000] After: NandSelect=40000002, nandConfig=04042300
[4294669.784000] Found NAND chip on Chip Select -1, chipSize=64MB, usable size=6
4MB, base=0x
[4294669.785000] brcmnand_scan: B4 nand_select = 40000002
[4294669.785000] brcmnand_scan: After nand_select = 40000002
[4294669.786000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shi
ft=14
[4294669.787000] Brcm NAND controller version = 3.2 NAND flash size 64MB @1c0000
00
[4294669.788000] mtd->oobsize=16, mtd->eccOobSize=16
[4294669.788000] brcmnand_scan: mtd->oobsize=16
[4294669.789000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[4294669.790000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel
=15, eccbytes=3
[4294669.791000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[4294669.793000] brcmnandCET: Status -> Deferred
[4294669.794000] numchips=1, size=4000000
[4294669.794000] Creating 4 MTD partitions on "bcm7xxx-nand.0":
[4294669.795000] 0x0000000000000000-0x0000000004000000 : "complete"
[4294669.799000] 0x0000000000000000-0x0000000000040000 : "loader"
[4294669.800000] 0x0000000000040000-0x0000000000400000 : "boot partition"
[4294669.801000] 0x0000000000400000-0x0000000004000000 : "root partition"
[4294669.805000] ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
[4294669.806000] brcm-pm: enabling power to USB block
[4294669.807000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (E
HCI-brcm-0)
[4294669.808000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294669.809000] - USB h/w setup mode <B>
[4294669.809000] - USB power enable set for active LOW mode
[4294669.810000] brcm-ehci brcm-ehci.0: BRCM EHCI
[4294669.810000] brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus num
ber 1
[4294669.811000] brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
[4294669.812000] brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 De
c 2004
[4294669.813000] usb usb1: configuration #1 chosen from 1 choice
[4294669.814000] hub 1-0:1.0: USB hub found
[4294669.815000] hub 1-0:1.0: 2 ports detected
[4294669.916000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (E
HCI-brcm-1)
[4294669.916000] hub 1-0:1.0: over-current change on port 1
[4294669.918000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294669.918000] brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
[4294669.919000] brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus
number 2
[4294669.920000] brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500
[4294669.921000] brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 1
0 Dec 2004
[4294669.922000] usb usb2: configuration #1 chosen from 1 choice
[4294669.923000] hub 2-0:1.0: USB hub found
[4294669.923000] hub 2-0:1.0: 2 ports detected
[4294670.017000] hub 1-0:1.0: over-current change on port 2
[4294670.025000] ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
[4294670.025000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHC
I-brcm-0)
[4294670.027000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.027000] - Resetting at b0480408
[4294670.028000] <-- brcm_start_hc
[4294670.028000] brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
[4294670.029000] brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus
number 3
[4294670.030000] brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
[4294670.086000] usb usb3: configuration #1 chosen from 1 choice
[4294670.087000] hub 3-0:1.0: USB hub found
[4294670.087000] hub 3-0:1.0: 2 ports detected
[4294670.118000] hub 2-0:1.0: over-current change on port 1
[4294670.189000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHC
I-brcm-1)
[4294670.190000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.191000] - Resetting at b0480608
[4294670.191000] <-- brcm_start_hc
[4294670.192000] brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
[4294670.192000] brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus
number 4
[4294670.193000] brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600
[4294670.249000] usb usb4: configuration #1 chosen from 1 choice
[4294670.250000] hub 4-0:1.0: USB hub found
[4294670.250000] hub 4-0:1.0: 2 ports detected
[4294670.352000] Initializing USB Mass Storage driver...
[4294670.352000] usbcore: registered new driver usb-storage
[4294670.353000] USB Mass Storage support registered.
[4294670.354000] i2c /dev entries driver
[4294670.354000] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu
Jun 22 13:55:50 2006 UTC).
[4294670.355000] ALSA device list:
[4294670.356000] No soundcards found.
[4294670.356000] TCP bic registered
[4294670.357000] NET: Registered protocol family 1
[4294670.357000] NET: Registered protocol family 17
[4294671.860000] Sending DHCP requests ., OK
[4294675.189000] IP-Config: Got DHCP answer from 0.0.0.0, my address is 10.10.11
.2
[4294675.191000] IP-Config: Complete:
[4294675.191000] device=eth0, addr=10.10.11.2, mask=255.255.255.0, gw=10.1
0.11.254,
[4294675.192000] host=10.10.11.2, domain=, nis-domain=(none),
[4294675.193000] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
[4294675.196000] No filesystem could mount root, tried: ext3 msdos vfat
[4294675.197000] Kernel panic - not syncing: VFS: Unable to mount root fs on unk
nown-block(31,3)
[4294675.198000] <0>Rebooting in 180 seconds.. -
versuche erst mal ein aktuelles image zu flashen. da ist noch ein uraltes image drauf.
-
Also: Wenn ich mit Dreamup über die serielle Schnittstelle versuche zu flashen, wird die neue Datei einwandfrei übertragen, beim "aus dem lokalen RAM" flashen bleibt die Sache dann stecken, 20 Minuten später ist immer noch keine Antwort auf dem Schirm. Wenn man das Ding dann per aus/an neu startet, kommen die Meldungen, die ich hier schon gepostet habe.
--> defekt?
Viele Grüße,
Jens.
-
sehr wahrscheinlich.
-
habe ich die Box gerade zurückgeschickt...
Danke für die Hilfe!
Da das "nicht Funktionieren" wohl kein Einzelfall ist, muss man wohl lokal kaufen und sich das Ding im Laden vorführen lassen...
Viele Grüße,
Jens.