Neustart zerstört UBIFSImage und Boot-Vorang

  • Neustart zerstört UBIFSImage und Boot-Vorang

    Immer wieder habe ich mit meiner DM7020HD das Problem, dass sie nach dem Neustart im Bootscreen wo die IP im Display angezeigt wird hängen bleibt.

    Quellcode

    1. Dreambox DM7020HD
    2. FIRST STAGE 1.3/400 {BO23456}
    3. 2ND STAGE OK, build #89 (2015-03-09)
    4. 0.000 - BCM board setup
    5. 0.002 - fp init
    6. FP version 6 detected
    7. 0.003 - ca init
    8. 0.506 - load config
    9. 0.533 - config loaded.
    10. * press [S] to enter setup
    11. OLED found!
    12. lcd: BOOT #89
    13. P23 detected!
    14. detected 2K pagesize, 128K blocksize
    15. - read config file: /boot/secondstage.conf
    16. detected jffs2 blocksize: 128kb
    17. +++++++++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
    18. dreamupd initialized
    19. Scanning JFFS2 FS: . done.
    20. find_inode failed for name=secondstage.conf
    21. load: Failed to find inode
    22. - failed to open /boot/secondstage.conf
    23. - failed to open /cf/autorun.bat
    24. lcd: /boot/bootlogo-dm7020hd.elf.gz
    25. bootlogo size: 74862
    26. Supported modes: 1080i !1080p 720p 480p 1080i_50Hz !1080p_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p DVI_800x600p DVI_1024x768p !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_Red !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz !DVI_1920x1080p_60Hz_Red !Custom0 !Custom1
    27. best supported mode is 25
    28. using 1920x1080i (50.00 Hz)
    29. HDMI
    30. using colorspace: 1
    31. create surface 1920 1080
    32. Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
    33. parsing JPEG header..
    34. Virtual FB Size: 1280x720
    35. lcd: /boot/vmlinux-3.2-dm7020hd.gz
    36. [ 0.000000] Linux version 3.2-dm7020hd (oe@porky.dream-property.net) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Mon Mar 16 21:23:22 UTC 2015
    37. [ 0.000000] Fetching vars from bootloader...
    38. [ 0.000000] Early serial console at MMIO32 0x10400b00 (options '1000000n8')
    39. [ 0.000000] bootconsole [uart0] enabled
    40. [ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
    41. [ 0.000000] Using 512 MB RAM (from straps)
    42. [ 0.000000] Fetch var 'memsize' = '64'
    43. [ 0.000000] CPU revision is: 0002a044 (Brcm4380)
    44. [ 0.000000] FPU revision is: 00130001
    45. [ 0.000000] Determined physical RAM map:
    46. [ 0.000000] memory: 10000000 @ 00000000 (usable)
    47. [ 0.000000] memory: 10000000 @ 20000000 (usable)
    48. [ 0.000000] bmem: adding 58 MB LINUX region at 5 MB (0x03a06000@0x005fa000)
    49. [ 0.000000] bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
    50. [ 0.000000] bmem: adding 256 MB LINUX region at 512 MB (0x10000000@0x20000000)
    51. [ 0.000000] Zone PFN ranges:
    52. [ 0.000000] Normal 0x00000000 -> 0x00030000
    53. [ 0.000000] Movable zone start PFN for each node
    54. [ 0.000000] early_node_map[2] active PFN ranges
    55. [ 0.000000] 0: 0x00000000 -> 0x00010000
    56. [ 0.000000] 0: 0x00020000 -> 0x00030000
    57. [ 0.000000] On node 0 totalpages: 131072
    58. [ 0.000000] Normal zone: 1536 pages used for memmap
    59. [ 0.000000] Normal zone: 0 pages reserved
    60. [ 0.000000] Normal zone: 129536 pages, LIFO batch:31
    61. [ 0.000000] PERCPU: Embedded 7 pages/cpu @81407000 s5440 r8192 d15040 u32768
    62. [ 0.000000] pcpu-alloc: s5440 r8192 d15040 u32768 alloc=8*4096
    63. [ 0.000000] pcpu-alloc: [0] 0 [0] 1
    64. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
    65. [ 0.000000] Kernel command line: ubi.mtd=root root=ubi0:rootfs rootfstype=ubifs rw console=ttyS0,115200 debug bmem=192M@64M
    66. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
    67. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    68. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    69. [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
    70. [ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
    71. [ 0.000000] Memory: 316976k/524288k available (4755k kernel code, 207312k reserved, 1008k data, 224k init, 0k highmem)
    72. [ 0.000000] Hierarchical RCU implementation.
    73. [ 0.000000] NR_IRQS:128
    74. [ 0.000000] Measuring MIPS counter frequency...
    75. [ 0.000000] Detected MIPS clock frequency: 405 MHz (202.508 MHz counter)
    76. [ 0.000000] Console: colour dummy device 80x25
    77. [ 0.000000] Calibrating delay loop... 403.45 BogoMIPS (lpj=201728)
    78. [ 0.011000] pid_max: default: 32768 minimum: 301
    79. [ 0.012000] Mount-cache hash table entries: 512
    80. [ 0.014000] SMP: Booting CPU1...
    81. [ 0.015000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
    82. [ 0.015000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
    83. [ 0.016000] CPU revision is: 0002a044 (Brcm4380)
    84. [ 0.016000] FPU revision is: 00130001
    85. [ 0.026000] SMP: CPU1 is running
    86. [ 0.026000] Brought up 2 CPUs
    87. [ 0.027000] devtmpfs: initialized
    88. [ 0.031000] NET: Registered protocol family 16
    89. [ 0.033000] PCI2.3->SDRAM window: 512 MB
    90. [ 0.040000] bio: create slab <bio-0> at 0
    91. [ 0.042000] SCSI subsystem initialized
    92. [ 0.042000] libata version 3.00 loaded.
    93. [ 0.043000] usbcore: registered new interface driver usbfs
    94. [ 0.043000] usbcore: registered new interface driver hub
    95. [ 0.044000] usbcore: registered new device driver usb
    96. [ 0.045000] Advanced Linux Sound Architecture Driver Version 1.0.24.
    97. [ 0.046000] pci 0000:01:00.0: [14e4:8602] type 0 class 0x000101
    98. [ 0.047000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
    99. [ 0.047000] pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
    100. [ 0.048000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
    101. [ 0.049000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
    102. [ 0.050000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff])
    103. [ 0.051000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
    104. [ 0.052000] Switching to clocksource upg
    105. [ 0.065000] NET: Registered protocol family 2
    106. [ 0.097000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    107. [ 0.099000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    108. [ 0.101000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    109. [ 0.102000] TCP: Hash tables configured (established 16384 bind 16384)
    110. [ 0.103000] TCP reno registered
    111. [ 0.104000] UDP hash table entries: 256 (order: 1, 8192 bytes)
    112. [ 0.105000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    113. [ 0.106000] NET: Registered protocol family 1
    114. [ 0.107000] RPC: Registered named UNIX socket transport module.
    115. [ 0.108000] RPC: Registered udp transport module.
    116. [ 0.108000] RPC: Registered tcp transport module.
    117. [ 0.109000] RPC: Registered tcp NFSv4.1 backchannel transport module.
    118. [ 0.110000] PCI: CLS 0 bytes, default 64
    119. [ 0.113000] JFFS2 version 2.2. (NAND) (SUMMARY) c 2001-2006 Red Hat, Inc.
    120. [ 0.115000] SGI XFS with security attributes, large block/inode numbers, no debug enabled
    121. [ 0.118000] msgmni has been set to 619
    122. [ 0.119000] io scheduler noop registered
    123. [ 0.120000] io scheduler cfq registered (default)
    124. [ 0.121000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    125. ÿ[ 0.143000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
    126. [ 0.144000] console [ttyS0] enabled, bootconsole disabled
    127. [ 0.144000] console [ttyS0] enabled, bootconsole disabled
    128. [ 0.166000] serial8250.0: ttyS1 at MMIO 0x10400b80 (irq = 67) is a 16550A
    129. [ 0.169000] loop: module loaded
    130. [ 0.169000] sata_brcmstb 0000:01:00.0: version 4.0
    131. [ 0.170000] brcm-pm: enabling sata clocks
    132. [ 0.171000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
    133. [ 0.171000] PCI: Setting latency timer of device 0000:01:00.0 to 64
    134. [ 0.369000] scsi0 : sata_brcmstb
    135. [ 0.370000] scsi1 : sata_brcmstb
    136. [ 0.371000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
    137. [ 0.372000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
    138. [ 0.374000] Broadcom STB NAND controller (BrcmNand Controller)
    139. [ 0.374000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0
    140. [ 0.378000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:2e:bf:0f)
    141. [ 0.379000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    142. [ 0.380000] brcm-pm: enabling usb clocks
    143. [ 0.380000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
    144. [ 0.381000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
    145. [ 0.413000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
    146. [ 0.419000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
    147. [ 0.420000] hub 1-0:1.0: USB hub found
    148. [ 0.421000] hub 1-0:1.0: 2 ports detected
    149. [ 0.421000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
    150. [ 0.422000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
    151. [ 0.454000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
    152. [ 0.460000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
    153. [ 0.461000] hub 2-0:1.0: USB hub found
    154. [ 0.461000] hub 2-0:1.0: 2 ports detected
    155. [ 0.462000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    156. [ 0.463000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
    157. [ 0.464000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
    158. [ 0.465000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
    159. [ 0.530000] hub 3-0:1.0: USB hub found
    160. [ 0.531000] hub 3-0:1.0: 2 ports detected
    161. [ 0.532000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
    162. [ 0.532000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
    163. [ 0.533000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
    164. [ 0.599000] hub 4-0:1.0: USB hub found
    165. [ 0.600000] hub 4-0:1.0: 2 ports detected
    166. [ 0.601000] Initializing USB Mass Storage driver...
    167. [ 0.602000] usbcore: registered new interface driver usb-storage
    168. [ 0.602000] USB Mass Storage support registered.
    169. [ 0.603000] i2c /dev entries driver
    170. [ 0.603000] ALSA device list:
    171. [ 0.604000] No soundcards found.
    172. [ 0.605000] TCP cubic registered
    173. [ 0.605000] NET: Registered protocol family 17
    174. [ 0.606000] Registering the dns_resolver key type
    175. [ 0.606000] EBI CS1: setting up NAND flash (primary)
    176. [ 0.608000] mtd->oobsize=0, mtd->eccOobSize=0
    177. [ 0.608000] NAND_CS_NAND_XOR=00000000
    178. [ 0.609000] B4: NandSelect=40000202, nandConfig=18152300, chipSelect=1
    179. [ 0.609000] brcmnand_read_id: CS1: dev_id=ecd35195
    180. [ 0.610000] After: NandSelect=40000202, nandConfig=18152300
    181. [ 0.611000] Block size=00020000, erase shift=17
    182. [ 0.611000] NAND Config: Reg=18152300, chipSize=1024 MB, blockSize=128K, erase_shift=11
    183. [ 0.612000] busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
    184. [ 0.613000] timing1 not adjusted: 5363444f
    185. [ 0.613000] timing2 not adjusted: 00000fc6
    186. [ 0.614000] eccLevel=15, 1Ksector=0, oob=16
    187. [ 0.614000] nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
    188. [ 0.615000] <--brcmnand_set_acccontrol: acc b4: f7ff1010, after: f7ff1010
    189. [ 0.616000] BrcmNAND mfg ec d3 Samsung K9F8G08U0M 1024MB on CS1
    190. [ 0.617000]
    191. [ 0.617000] Found NAND on CS1: ACC=f7ff1010, cfg=18152300, flashId=ecd35195, tim1=5363444f, tim2=00000fc6
    192. [ 0.618000] BrcmNAND version = 0x0302 1024MB @00000000
    193. [ 0.619000] B4: NandSelect=40000202, nandConfig=18152300, chipSelect=1
    194. [ 0.619000] brcmnand_read_id: CS1: dev_id=ecd35195
    195. [ 0.620000] After: NandSelect=40000202, nandConfig=18152300
    196. [ 0.621000] Found NAND flash on Chip Select 1, chipSize=1024MB, usable size=1024MB, base=0
    197. [ 0.622000] brcmnand_scan: B4 nand_select = 40000202
    198. [ 0.622000] brcmnand_scan: After nand_select = 40000202
    199. [ 0.623000] page_shift=11, bbt_erase_shift=17, chip_shift=30, phys_erase_shift=17
    200. [ 0.624000] Brcm NAND controller version = 3.2 NAND flash size 1024MB @00000000
    201. [ 0.625000] ECC layout=brcmnand_oob_64
    202. [ 0.625000] brcmnand_scan: mtd->oobsize=64
    203. [ 0.626000] brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
    204. [ 0.626000] brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
    205. [ 0.627000] -->brcmnand_default_bbt
    206. [ 0.628000] brcmnand_default_bbt: bbt_td = bbt_main_descr
    207. [ 0.629000] Bad block table Bbt0 found at page 0007ffc0, version 0x01 for chip on CS1
    208. [ 0.630000] Bad block table 1tbB found at page 0007ff80, version 0x01 for chip on CS1
    209. [ 0.631000] nand_read_bbt: Bad block at 0x08c80000
    210. [ 0.632000] nand_read_bbt: Bad block at 0x19a20000
    211. [ 0.633000] nand_read_bbt: Bad block at 0x1bde0000
    212. [ 0.633000] nand_read_bbt: Bad block at 0x24280000
    213. [ 0.634000] nand_read_bbt: Bad block at 0x25e40000
    214. [ 0.634000] nand_read_bbt: Bad block at 0x26140000
    215. [ 0.635000] nand_read_bbt: Bad block at 0x26540000
    216. [ 0.636000] brcmnandCET: Did not find CET, recreating
    217. [ 0.639000] brcmnandCET: Status -> Deferred
    218. [ 0.640000] Adjust partition complete size from 40000000 to 3ff80000 to avoid overlap with BBT reserved space
    219. [ 0.641000] Adjust partition root size from 3f800000 to 3f780000 to avoid overlap with BBT reserved space
    220. [ 0.643000] Creating 4 MTD partitions on "brcmnand.0":
    221. [ 0.643000] 0x000000000000-0x00003ff80000 : "complete"
    222. [ 0.652000] 0x000000000000-0x000000100000 : "loader"
    223. [ 0.654000] 0x000000100000-0x000000800000 : "boot"
    224. [ 0.656000] 0x000000800000-0x00003ff80000 : "root"
    225. [ 0.668000] UBI: attaching mtd3 to ubi0
    226. [ 0.668000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
    227. [ 0.669000] UBI: logical eraseblock size: 126976 bytes
    228. [ 0.670000] UBI: smallest flash I/O unit: 2048
    229. [ 0.670000] UBI: VID header offset: 2048 (aligned 2048)
    230. [ 0.671000] UBI: data offset: 4096
    231. [ 1.698000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    232. [ 1.742000] ata1.00: ATA-8: WDC WD10EADS-00L5B1, 01.01A01, max UDMA/133
    233. [ 1.743000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
    234. [ 1.748000] ata1.00: configured for UDMA/133
    235. [ 1.749000] scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00L 01.0 PQ: 0 ANSI: 5
    236. [ 1.751000] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    237. [ 1.752000] sd 0:0:0:0: [sda] Write Protect is off
    238. [ 1.753000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    239. [ 1.753000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    240. [ 1.781000] sda: sda1 sda2
    241. [ 1.784000] sd 0:0:0:0: [sda] Attached SCSI disk
    242. [ 2.077000] ata2: SATA link down (SStatus 4 SControl 300)
    243. [ 5.255000] UBI: max. sequence number: 31534
    244. [ 5.288000] UBI: attached mtd3 to ubi0
    245. [ 5.289000] UBI: MTD device name: "root"
    246. [ 5.289000] UBI: MTD device size: 1015 MiB
    247. [ 5.290000] UBI: number of good PEBs: 8117
    248. [ 5.290000] UBI: number of bad PEBs: 7
    249. [ 5.291000] UBI: number of corrupted PEBs: 0
    250. [ 5.292000] UBI: max. allowed volumes: 128
    251. [ 5.292000] UBI: wear-leveling threshold: 4096
    252. [ 5.293000] UBI: number of internal volumes: 1
    253. [ 5.293000] UBI: number of user volumes: 2
    254. [ 5.294000] UBI: available PEBs: 0
    255. [ 5.294000] UBI: total number of reserved PEBs: 8117
    256. [ 5.295000] UBI: number of PEBs reserved for bad PEB handling: 81
    257. [ 5.296000] UBI: max/mean erase counter: 121/4
    258. [ 5.296000] UBI: image sequence number: 921713743
    259. [ 5.297000] UBI: background thread "ubi_bgt0d" started, PID 51
    260. [ 5.336000] UBIFS: recovery needed
    261. [ 5.349000] UBIFS: recovery completed
    262. [ 5.349000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
    263. [ 5.350000] UBIFS: file system size: 420163584 bytes (410316 KiB, 400 MiB, 3309 LEBs)
    264. [ 5.351000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
    265. [ 5.352000] UBIFS: media format: w4/r0 (latest is w4/r0)
    266. [ 5.352000] UBIFS: default compressor: lzo
    267. [ 5.353000] UBIFS: reserved for root: 0 bytes (0 KiB)
    268. [ 5.355000] VFS: Mounted root (ubifs filesystem) on device 0:13.
    269. [ 5.358000] devtmpfs: mounted
    270. [ 5.359000] Freeing unused kernel memory: 224k freed
    271. [ 5.389000] UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 0)
    272. [ 5.390000] UBIFS error (pid 1): ubifs_read_node: bad node at LEB 2022:14984, LEB mapping status 0
    273. [ 5.391000] UBIFS error (pid 1): ubifs_iget: failed to read inode 410, error -22
    274. [ 5.392000] UBIFS error (pid 1): ubifs_lookup: dead directory entry 'etc', error -22
    275. [ 5.393000] UBIFS warning (pid 1): ubifs_ro_mode: switched to read-only mode, error -22
    276. [ 5.394000] Call Trace:
    277. [ 5.394000] [<8049d3d4>] dump_stack+0x8/0x34
    278. [ 5.395000] [<801fb738>] ubifs_lookup+0x178/0x180
    279. [ 5.395000] [<800c4af4>] d_alloc_and_lookup+0x4c/0x88
    280. [ 5.396000] [<800c5100>] do_lookup+0x2f4/0x418
    281. [ 5.396000] [<800c5d5c>] link_path_walk+0x154/0x994
    282. [ 5.397000] [<800c6d90>] path_lookupat+0x64/0x890
    283. [ 5.398000] [<800c828c>] do_path_lookup+0x30/0xa0
    284. [ 5.398000] [<800c99bc>] user_path_at_empty+0x60/0xa8
    285. [ 5.399000] [<800c9a14>] user_path_at+0x10/0x1c
    286. [ 5.399000] [<800b7bd0>] sys_faccessat+0x1c0/0x220
    287. [ 5.400000] [<8000c85c>] stack_done+0x20/0x40
    288. [ 5.400000]
    289. [ 5.404000] UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 0)
    290. [ 5.404000] UBIFS error (pid 1): ubifs_read_node: bad node at LEB 2022:14984, LEB mapping status 0
    291. [ 5.406000] UBIFS error (pid 1): ubifs_iget: failed to read inode 410, error -22
    292. [ 5.406000] UBIFS error (pid 1): ubifs_lookup: dead directory entry 'etc', error -22
    293. [ 5.489000] UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 0)
    294. [ 5.489000] UBIFS error (pid 1): ubifs_read_node: bad node at LEB 2022:2048, LEB mapping status 0
    295. [ 5.491000] UBIFS error (pid 1): ubifs_iget: failed to read inode 7166, error -22
    296. [ 5.491000] UBIFS error (pid 1): ubifs_lookup: dead directory entry 'utmp', error -22
    297. INIT: version 2.88 booting
    298. [ 5.502000] UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 0)
    299. [ 5.503000] UBIFS error (pid 1): ubifs_read_node: bad node at LEB 2022:14984, LEB mapping status 0
    300. [ 5.504000] UBIFS error (pid 1): ubifs_iget: failed to read inode 410, error -22
    301. [ 5.505000] UBIFS error (pid 1): ubifs_lookup: dead directory entry 'etc', error -22
    302. [ 5.517000] UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 0)
    303. [ 5.518000] UBIFS error (pid 1): ubifs_read_node: bad node at LEB 2022:14984, LEB mapping status 0
    304. [ 5.519000] UBIFS error (pid 1): ubifs_iget: failed to read inode 410, error -22
    305. [ 5.520000] UBIFS error (pid 1): ubifs_lookup: dead directory entry 'etc', error -22
    306. INIT: No inittab file found
    307. [ 5.536000] UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 0)
    308. [ 5.537000] UBIFS error (pid 1): ubifs_read_node: bad node at LEB 2022:2048, LEB mapping status 0
    309. [ 5.538000] UBIFS error (pid 1): ubifs_iget: failed to read inode 7166, error -22
    310. [ 5.539000] UBIFS error (pid 1): ubifs_lookup: dead directory entry 'utmp', error -22
    Alles anzeigen

    Kann mir jemand sagen wie das passieren kann bzw. was da passiert

    Image ist das DMM Stabile OE 2.2 Image
    In Betrieb
    Dreambox 7080HD-S2/C
    Ausser Betrieb
    Dreambox 8000-S2
    Defekt
    Dreambox 7025-S