Any hint in the bootlog please?

Hi Zeros,
Thanks a lot for trying to help, but I think I made myself clear:
It's not the tv, it's the dm900.
I have tested in another tv and the results are the same.
Please, someone who can read the bootlog:
Is there any indication there on where the fault can be?

I have tested in another TV with another cable.
Still no luck.

I am aware of the problems with my TV, but this is not the case.

As I mentioned, my TV accepts the signal from HDMI of my receiver.
I have an Android device attached and I can display up to 4K 10 bit.

I have also tested the box in another TV.
The result is the same. No picture via HDMI.

So, I'm quite sure that the problem is my DM900.
My question is: is there any possibility to diagnose and fix it without sending the box for repair?
Does the log describes the problem?

Thanks!

HDMI CEC was on with default settings.
I turned it off and still no picture

The log is fron non original image. But shory after I took yhe log, I did an online restore and now I am using the original image.
I did not change any CEC settings.
My TV is LG OLED 65EF950V.
It goes through a Yamaha receiver in which I have connected an Android player which works fine.

I have tested with another working cable and directly to tv hdmi port, but the result is the same.

BTW, does the startup log say anything about the state of the hardware?

Should I return it to dmm to fix?

Thanks a lot for your time

Hi,
Sorry for the delay. Busy with life

Attached is the log from the startup.

OK. Thanks. Will do so tonight.

Hi All,
Suddenly I am not having my DM900 output anything via HDMI.
I have changed the cable, checked the TV ports, and everything else is working fine.

Just the HDMI out port is not working.
The box is still under warranty, but I want to save the trip to the factory as it usually takes a couple of months from where I am (Albania).

So, I kindly ask your help in determining where the fault might be, and if there is an easy fix(by replacing something easy),
or, maybe an workaround (like "adapting" HDMI IN to work as HDMI OUT, replace the connectors) or anything.

Thanks for any eventual hint!

It wasn't meant as a sign of disrespect. Just wanted to point out that I tried to register but it wasn't possible. And this was not the main issue. The main issue for me is the German language. Most of discussions are very difficult to follow.
And my question was simple: as you are working closely with oozoon maybe you create an image with multiboot support built-in.
But, hey it's up to you. As all choices in life...

In a forum that do not accept yahoo.com addresses?

I have installed oozoon image and the Barry Allen from feeds, but it does not appear in the plugins.
Then installed it manually and again no Barry Allen.
The installation goes fine and there are no errors reported.

I want to give DarkShadow a go, but I'd need some help.

Can you please be more specific: what image? Where to download?
Is there any image ready so I have multiboot out of the box?

I used to be good some years ago, but things got easier and easier, so I seem to have lost the touch

Thanks anyways guys!

Yes I have seen it exist with 3GB, but I cannot mount it.
Also, if possible I would like to make it available for multi-boot.
Thanks!

Hi,

My DM900 only shows 1GB of flash and 1GB of RAM.
I have read elsewhere that RAM is used for video and it is just 1GB left for APPS.

Also, I have read that there are two partitions of flash (1GB + 3GB).
Can you please help me identify, format, and mount the 3GB partition(a simple step by step guide with commands will be highly appreciated)
Also, if I succeed with the above, can I use the new partition for multi-boot images?

Thanks in advance!

Bump!
DMM is a international company, I assume, so English section must be monitored more often.
I would prefer even a quick answer: we are not helping you because we do not like to.
But leaving a post without answer in an official forum is not understandable

Hi,
Being my first post here, I'd like to send a warm Hello! to all forum members.
I have been a DMM products user since Magic module, and now I have a DM800HD se.
Recently, I dived in 3d world, and my DM does almost everything superbly.
But, having to download most of the content, I am facing two problems.
1. Most of the content i download has DTS soundtrack. I have managed to downgrade sound through a plugin, but it looses all the fun.
My home theatre is:
Panasonic SC-BT330EG-K
which is supposed to decode DTS. Despite of this, I have no sound (so passthrough feature is not working)
Box and receiver are linked through toslink cable that works OK for AC3 streams.
2. 3d subtitles are not working. I can see the subtitles in my PC, but not in my box. Can, you please, tell me which are the 3d subtitle type that are supported by DM800HD se?

Thanks in Advance!