bei Samsung TVs heisst der Modus "Just Scan", kannst du normalerweise mit der Taste für Bildgröße durchschalten.
Beiträge von mac110
-
-
Danke dir vielmals, es hat geholfen . Ich schulde dir einen Kasten Bier
-
wie gesagt nach dem software update ist die box nicht mehr hochgefahren und ich habe das online recovery angestoßen, was auch bis initiating reboot durchlief und dann ist nichts mehr passiert. Habe dann nach 10 Minuten die Box mit dem Netzschalter aus und wieder eingeschalten.
-
So hier das Bootlog:
Code
Alles anzeigen=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.10.14 21:53:43 =~=~=~=~=~=~=~=~=~=~=~= Dreambox DM7 080 M0 M1 SHMOO 0 00000000 1 00000000 C do_boot 3s enter setup 2 1 0 enter setup . . . SL2=1 LLMB=0000C000 BP=02000000 L2Cfg=1E76C637 L2Buf=44707700 BrCfg=F01C204F BrMod=02800001 BrZp0=05000000 BrZp1=00002000 #@ BCM97434B0 CFE v3.15, Endian Mode: Little Build Date: 20140202 (dm@dm) Copyright (C) Broadcom Corporation. MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256 found card in known state ca valid! CPU speed: 1407MHz DDR Frequency: 667 MHz DDR Mode: DDR3 Total memory(MEMC 0): 1024MB MEMC 0 DDR Width: 32 Total memory(MEMC 1): 1024MB MEMC 1 DDR Width: 32 CFE initialized. *** Autoboot: Trying device 'flash0.kernel' file kernel (flash0.kernel,raw) Loader:elf Filesys:raw Dev:flash0.kernel File:kernel Options: Loading: 0x80001000/18266752 0x8116ca80/280688 Entry address is 0x80580110 Starting program at 0x80580110 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4-3.0-dm7080 (dora@tigger.dream-property.net) (gcc version 4.8.1 (GCC) ) #15 SMP Sat Sep 13 12:12:38 UTC 2014 [ 0.000000] Fetching vars from bootloader... found 13 vars. [ 0.000000] Options: moca=0 sata=1 pcie=1 usb=1 [ 0.000000] Using 1024 MB + 1024 MB RAM (from CFE) [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] memory: 30000000 @ 20000000 (usable) [ 0.000000] bmem: adding 384 MB RESERVED region at 640 MB (0x18000000@0x28000000) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00050000 [ 0.000000] HighMem empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] 0: 0x00020000 -> 0x00050000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @819c8000 s6784 r8192 d13696 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259584 [ 0.000000] Kernel command line: bmem=384M@640M memc1=768M console=ttyS0,1000000 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.000000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.000000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.000000] Memory: 628084k/1048576k available (5694k kernel code, 420492k reserved, 1182k data, 10960k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:160 [ 0.000000] Measuring MIPS counter frequency... [ 0.000000] Detected MIPS clock frequency: 1407 MHz (175.886 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] Calibrating delay loop... 935.93 BogoMIPS (lpj=467968) [ 0.009000] pid_max: default: 32768 minimum: 301 [ 0.009000] Mount-cache hash table entries: 512 [ 0.010000] Initializing cgroup subsys cpuacct [ 0.010000] Initializing cgroup subsys devices [ 0.011000] Initializing cgroup subsys freezer [ 0.012000] SMP: Booting CPU1... [ 0.012000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.012000] FPU revision is: 00130001 [ 0.012000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.012000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.012000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.022000] SMP: CPU1 is running [ 0.022000] SMP: Booting CPU2... [ 0.022000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.022000] FPU revision is: 00130001 [ 0.022000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.022000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.022000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.031000] SMP: CPU2 is running [ 0.031000] SMP: Booting CPU3... [ 0.031000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.031000] FPU revision is: 00130001 [ 0.031000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.031000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.031000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.040000] SMP: CPU3 is running [ 0.040000] Brought up 4 CPUs [ 0.040000] devtmpfs: initialized [ 0.043000] bmem: adding extra 1024 MB RESERVED region at 2304 MB (0x40000000@0x90000000) [ 0.044000] NET: Registered protocol family 16 [ 0.045000] USB0: power enable is active high; overcurrent is active low [ 0.045000] USB1: power enable is active high; overcurrent is active low [ 0.046000] PCI: PCIe link up, 5.0Gbps x1 [ 0.049000] bio: create slab <bio-0> at 0 [ 0.050000] SCSI subsystem initialized [ 0.051000] usbcore: registered new interface driver usbfs [ 0.051000] usbcore: registered new interface driver hub [ 0.052000] usbcore: registered new device driver usb [ 0.052000] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.053000] PCI host bridge to bus 0000:00 [ 0.053000] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff] [ 0.054000] pci_bus 0000:00: root bus resource [mem 0x00000400-0x000007ff] [ 0.054000] PCI: found device 104c:8241 on PCIe bus, slot 0 (irq 36) [ 0.055000] pci 0000:00:00.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff 64bit] [ 0.056000] pci 0000:00:00.0: BAR 2: assigned [mem 0xd0010000-0xd0011fff 64bit] [ 0.057000] Bluetooth: Core ver 2.16 [ 0.057000] NET: Registered protocol family 31 [ 0.057000] Bluetooth: HCI device and connection manager initialized [ 0.058000] Bluetooth: HCI socket layer initialized [ 0.058000] Bluetooth: L2CAP socket layer initialized [ 0.059000] Bluetooth: SCO socket layer initialized [ 0.059000] cfg80211: Calling CRDA to update world regulatory domain [ 0.060000] Switching to clocksource wktmr [ 0.066000] NET: Registered protocol family 2 [ 0.067000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.068000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.072000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.074000] TCP: Hash tables configured (established 131072 bind 65536) [ 0.074000] TCP: reno registered [ 0.075000] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.075000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.076000] NET: Registered protocol family 1 [ 0.077000] RPC: Registered named UNIX socket transport module. [ 0.078000] RPC: Registered udp transport module. [ 0.078000] RPC: Registered tcp transport module. [ 0.079000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.080000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.139000] NFS: Registering the id_resolver key type [ 0.140000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.142000] msgmni has been set to 1226 [ 0.143000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.144000] io scheduler noop registered [ 0.144000] io scheduler cfq registered (default) [ 0.145000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.146000] serial8250.0: ttyS0 at MMIO 0x10406b00 (irq = 67) is a 16550A [ 0.147000] console [ttyS0] enabled, bootconsole disabled [ 0.147000] console [ttyS0] enabled, bootconsole disabled [ 0.149000] loop: module loaded [ 0.150000] ahci: SSS flag set, parallel bus scan disabled [ 0.161000] ahci strict-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 0.162000] ahci strict-ahci.0: flags: ncq sntf stag clo slum part [ 0.166000] scsi0 : ahci_platform [ 0.167000] scsi1 : ahci_platform [ 0.167000] ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 46 [ 0.168000] ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 46 [ 0.170000] tun: Universal TUN/TAP device driver, 1.6 [ 0.170000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 0.463000] Found PHY at Address 3 [ 0.463000] bcmgenet: configuring instance #0 for external RGMII [ 0.464000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.465000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.465000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.475000] ata1: SATA link down (SStatus 0 SControl 300) [ 0.495000] ehci-brcm ehci-brcm.0: irq 71, io mem 0x10480300 [ 0.501000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.502000] hub 1-0:1.0: USB hub found [ 0.502000] hub 1-0:1.0: 1 port detected [ 0.503000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI [ 0.503000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 [ 0.533000] ehci-brcm ehci-brcm.1: irq 72, io mem 0x10480500 [ 0.539000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 [ 0.539000] hub 2-0:1.0: USB hub found [ 0.540000] hub 2-0:1.0: 1 port detected [ 0.540000] ehci-brcm ehci-brcm.2: Broadcom STB EHCI [ 0.541000] ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3 [ 0.571000] ehci-brcm ehci-brcm.2: irq 76, io mem 0x10490300 [ 0.577000] ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00 [ 0.577000] hub 3-0:1.0: USB hub found [ 0.578000] hub 3-0:1.0: 1 port detected [ 0.578000] ehci-brcm ehci-brcm.3: Broadcom STB EHCI [ 0.579000] ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4 [ 0.609000] ehci-brcm ehci-brcm.3: irq 77, io mem 0x10490500 [ 0.615000] ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00 [ 0.615000] hub 4-0:1.0: USB hub found [ 0.616000] hub 4-0:1.0: 1 port detected [ 0.617000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.617000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 0.618000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5 [ 0.619000] ohci-brcm ohci-brcm.0: irq 73, io mem 0x10480400 [ 0.681000] hub 5-0:1.0: USB hub found [ 0.681000] hub 5-0:1.0: 1 port detected [ 0.682000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI [ 0.682000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6 [ 0.683000] ohci-brcm ohci-brcm.1: irq 74, io mem 0x10480600 [ 0.746000] hub 6-0:1.0: USB hub found [ 0.746000] hub 6-0:1.0: 1 port detected [ 0.747000] ohci-brcm ohci-brcm.2: Broadcom STB OHCI [ 0.747000] ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7 [ 0.748000] ohci-brcm ohci-brcm.2: irq 78, io mem 0x10490400 [ 0.811000] hub 7-0:1.0: USB hub found [ 0.811000] hub 7-0:1.0: 1 port detected [ 0.812000] ohci-brcm ohci-brcm.3: Broadcom STB OHCI [ 0.812000] ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8 [ 0.813000] ohci-brcm ohci-brcm.3: irq 79, io mem 0x10490600 [ 0.876000] hub 8-0:1.0: USB hub found [ 0.876000] hub 8-0:1.0: 1 port detected [ 0.877000] xhci_hcd 0000:00:00.0: xHCI Host Controller [ 0.878000] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 9 [ 0.879000] xhci switched power on polarity [ 0.879000] hub 9-0:1.0: USB hub found [ 0.880000] hub 9-0:1.0: 2 ports detected [ 0.880000] xhci_hcd 0000:00:00.0: xHCI Host Controller [ 0.881000] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 10 [ 0.882000] hub 10-0:1.0: USB hub found [ 0.883000] hub 10-0:1.0: 2 ports detected [ 0.883000] Initializing USB Mass Storage driver... [ 0.884000] usbcore: registered new interface driver usb-storage [ 0.885000] USB Mass Storage support registered. [ 0.885000] i2c /dev entries driver [ 0.886000] usbcore: registered new interface driver btusb [ 0.886000] sdhci: Secure Digital Host Controller Interface driver [ 0.887000] sdhci: Copyright(c) Pierre Ossman [ 0.888000] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.888000] sdhci-brcmstb sdhci-brcmstb.0: Enabling controller [ 0.894000] mmc0: SDHCI controller on sdhci-brcmstb.0 [sdhci-brcmstb.0] using ADMA [ 0.894000] sdhci-brcmstb sdhci-brcmstb.1: Enabling controller [ 0.900000] mmc1: SDHCI controller on sdhci-brcmstb.1 [sdhci-brcmstb.1] using ADMA [ 0.901000] TCP: cubic registered [ 0.901000] NET: Registered protocol family 10 [ 0.903000] NET: Registered protocol family 17 [ 0.903000] Bluetooth: RFCOMM TTY layer initialized [ 0.904000] Bluetooth: RFCOMM socket layer initialized [ 0.904000] Bluetooth: RFCOMM ver 1.11 [ 0.905000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.905000] Bluetooth: BNEP filters: protocol multicast [ 0.906000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.907000] L2TP core driver, V2.0 [ 0.907000] Registering the dns_resolver key type [ 0.908000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor [ 0.909000] EBI CS0: setting up SPI flash (primary) [ 0.910000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated [ 0.911000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address [ 0.911000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.917000] Creating 3 MTD partitions on "spi0.0": [ 0.918000] 0x000000000000-0x000001000000 : "entire_device" [ 0.919000] 0x000000000000-0x000000100000 : "bootloader" [ 0.920000] 0x000000100000-0x000001000000 : "recovery" [ 0.923000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 1.002000] mmc0: new high speed MMC card at address 0001 [ 1.003000] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 1.004000] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 1.005000] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 1.010000] mmcblk0: p1 p2 [ 1.012000] mmcblk0boot1: unknown partition table [ 1.013000] mmcblk0boot0: unknown partition table [ 1.014000] bcmgenet bcmgenet.0: eth0: link up, 100 Mbps, full duplex [ 1.015000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 1.026000] Sending DHCP requests ., OK [ 1.042000] IP-Config: Got DHCP answer from 192.168.2.1, my address is 192.168.2.41 [ 1.043000] IP-Config: Complete: [ 1.043000] device=eth0, addr=192.168.2.41, mask=255.255.255.0, gw=192.168.2.1 [ 1.044000] host=192.168.2.41, domain=fritz.box, nis-domain=(none) [ 1.045000] bootserver=192.168.2.1, rootserver=192.168.2.1, rootpath= [ 1.045000] ALSA device list: [ 1.046000] No soundcards found. [ 1.046000] Failed to execute /init INIT: version 2.88 booting Starting udev [ 1.143000] systemd-udevd[90]: starting version 206 [ 1.419000] stb_core: module license 'Proprietary' taints kernel. [ 1.420000] Disabling lock debugging due to kernel taint Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory bootlogd. rm: can't remove '/tmp': Device or resource busy Configuring network interfaces... udhcpc (v1.21.1) started Sending discover... Sending select for 192.168.2.41... Lease of 192.168.2.41 obtained, lease time 864000 /etc/udhcpc.d/50default: Adding DNS 192.168.2.1 done. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 INIT: Entering runlevel: 5 Starting Dropbear SSH server: Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key' Generating key, this may take a while... Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwCVnzk9yxbSfeHpfmLxS1EpF9+kBgchCULlZNwM7LNY0kTBmC+hgspG9g6zMe6wLQF41ywpNUX1+afUiKFG2bS5IuSYTgNaN0GW3xqE4DWkaV0ChqyWkIJiurs02M2f0TyO1bEA/QtqjoGtgj51xXhrPLBbG64jbl4NFHHUnR6+Yf6V root@dm7080 Fingerprint: md5 2b:90:04:ff:f5:92:f6:70:26:bb:07:01:ee:8d:e0:d8 dropbear. Starting recovery-ui. Starting internet superserver: xinetd. Starting Lighttpd Web Server: lighttpd. 1970-01-01 00:00:02: (log.c.164) server started Stopping Bootlog daemon: bootlogd. opendreambox 2.2.0 dm7080 /dev/ttyS0 >>> Your Dreambox has booted into RESCUE MODE. >>> Please log in as user 'root' (no password required), >>> then run 'help' to get further information. dm7080 login: [ 3.231000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.266000] ata2.00: ATA-8: WDC WD10EACS-07D6B1, 01.01A01, max UDMA/133 [ 3.266000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 3.268000] ata2.00: configured for UDMA/133 [ 3.269000] scsi 1:0:0:0: Direct-Access ATA WDC WD10EACS-07D 01.0 PQ: 0 ANSI: 5 [ 3.270000] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 3.271000] sd 1:0:0:0: [sda] Write Protect is off [ 3.272000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.294000] sda: sda1 sda2 [ 3.295000] sd 1:0:0:0: [sda] Attached SCSI disk
Ist evtl. das, das Problem? :
Code[ 1.012000] mmcblk0boot1: unknown partition table [ 1.013000] mmcblk0boot0: unknown partition table [ 1.046000] Failed to execute /init
/dev hat kein filesystem
Coderoot@dm7080:~# df -h Filesystem Size Used Available Use% Mounted on tmpfs 306.7M 24.0K 306.7M 0% /var/volatile none 306.7M 0 306.7M 0% /dev tmpfs 306.7M 0 306.7M 0% /dev/shm tmpfs 306.7M 108.0K 306.6M 0% /run tmpfs 306.7M 0 306.7M 0% /tmp
Was muss es denn für ein fs sein? ext4??
-
Danke dir!
Der von den älteren Boxen funktioniert unter win 8.1 x64 nicht aber der neue aus deinem Link ging einwandfrei!
-
nein geht leider nicht
Habe jetzt glücklicherweise eine mini usb kabel gefunden aber wo kriege den vcp treiber?? Auf www.dream-multimedia-tv.de/downloadcenter ist nichts
-
genau das meinte ich.
danke ich werde mich dann mal um das Bootlog kümmern
-
Ok und wo kriege ich den jetzt her und sollte der nicht mit dem flashen des images installiert werden?
-
und wie muss ich da bei der dm7080 vorgehen?
-
Seid heute morgen bootet meine 7080 immer nur noch direkt in den recovery modus, ohne das ich die Power Taste gedrückt habe.
Online Recovery habe ich schon probiert, aber das half leider nicht:
Code
Alles anzeigen[*] Mounting '/data' (ro) [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm7080/release/recovery.sig' [*] Copying 'recovery' from local storage [*] Verifying signature of 'recovery' gpgv: Signature made Fri Sep 5 22:05:37 2014 UTC using RSA key ID D6CF56E7 gpgv: key D6CF56E7 was created 1407768622 seconds in the future (time warp or clock problem) gpgv: key D6CF56E7 was created 1407768622 seconds in the future (time warp or clock problem) gpgv: key D6CF56E7 was created 1407768622 seconds in the future (time warp or clock problem) gpgv: Good signature from "Dreambox DM7080 Recovery <recovery@dm7080.com>" [*] Unmounting '/data' [*] Running './recovery' [*] Options '-v' [*] Mounting '/data' (ro) [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm7080/release/dreambox-image-dm7080.tar.xz.sig' [*] Copying 'dreambox-image-dm7080.tar.xz' from local storage [*] Verifying signature of 'dreambox-image-dm7080.tar.xz' gpgv: Signature made Sun Sep 28 18:58:59 2014 UTC using RSA key ID D6CF56E7 gpgv: key D6CF56E7 was created 1407768617 seconds in the future (time warp or clock problem) gpgv: key D6CF56E7 was created 1407768617 seconds in the future (time warp or clock problem) gpgv: key D6CF56E7 was created 1407768617 seconds in the future (time warp or clock problem) gpgv: Good signature from "Dreambox DM7080 Recovery <recovery@dm7080.com>" [*] Creating ext4 filesystem 'dreambox-rootfs' on /dev/mmcblk0p1 mke2fs 1.42.8 (20-Jun-2013) Filesystem label=dreambox-rootfs OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 60928 inodes, 243712 blocks 12185 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=251658240 8 block groups 32768 blocks per group, 32768 fragments per group 7616 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376 Allocating group tables: 0/8 done Writing inode tables: 0/8 done Creating journal (4096 blocks): done Writing superblocks and filesystem accounting information: 0/8 done [*] Mounting root filesystem [*] Extracting 'dreambox-image-dm7080.tar.xz' to '/mnt' [*] Flashing boot image [*] Creating boot image [*] Flashing boot image [*] Enabling boot source A [*] Unmounting '/mnt/dev' [*] Unmounting '/mnt/proc' [*] Unmounting '/mnt/run' [*] Unmounting '/mnt/sys' [*] Unmounting '/mnt/tmp' [*] Unmounting '/mnt' [*] Unmounting '/data' [*] Initiating reboot
aber das half leider nicht, Box bootet immer noch sofort ins Recovery.
Auch ein manuelles flashen hilft nicht.
Code
Alles anzeigen[*] Creating ext4 filesystem 'dreambox-rootfs' on /dev/mmcblk0p1 mke2fs 1.42.8 (20-Jun-2013) Filesystem label=dreambox-rootfs OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 60928 inodes, 243712 blocks 12185 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=251658240 8 block groups 32768 blocks per group, 32768 fragments per group 7616 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376 Allocating group tables: 0/8 done Writing inode tables: 0/8 done Creating journal (4096 blocks): done Writing superblocks and filesystem accounting information: 0/8 done [*] Mounting root filesystem [*] Extracting '/tmp/WEFvvz' to '/mnt' [*] Flashing boot image [*] Creating boot image [*] Flashing boot image [*] Enabling boot source A [*] Unmounting '/mnt/dev' [*] Unmounting '/mnt/proc' [*] Unmounting '/mnt/run' [*] Unmounting '/mnt/sys' [*] Unmounting '/mnt/tmp' [*] Unmounting '/mnt' [*] Finished successfully. You may reboot now.
Nach gutemines Rat habe ich es auch mal mit folgendem verucht:
Coderoot@dm7080:/boot# flash-kernel -a /usr/share/fastboot/lcd_anim.bin -m 0x1000000 0 -o A /boot/vmlinux.bin-3.4-3.0-dm7080 [*] Creating boot image [*] Flashing boot image [*] Enabling boot source A
die Box bootet aber immer noch direkt ins Recovery.
Mir ist noch aufgefallen, das etliche Module in /lib/modules/3.4-3.0-dm7080/extra/ selbst nach dem flashen fehlen.
-
/lib/modules/3.4-3.0-dm7080/extra/ ist komplett leer obwohl davor das image geflashed wurde
-
So hab es jetzt mit winscp kopiert und geflashed aber die box fährt nach reboot wieder in den recovery mode hoch!!!
Coderoot@dm7080:/boot# flash-kernel -a /usr/share/fastboot/lcd_anim.bin -m 0x1000000 0 -o A /boot/vmlinux.bin-3.4-3.0-dm7080 [*] Creating boot image [*] Flashing boot image [*] Enabling boot source A
Weiß echt nicht was ich noch machen soll
WEnn man das online recovery ausführt dann kommt noch folgendes:
CodeAllocating group tables: 0/8 done Writing inode tables: 0/8 done Creating journal (4096 blocks): done Writing superblocks and filesystem accounting information: 0/8 done
wieso eigentlich immer 0 von 8 ?
-
in /boot liegt nichts drin und wie soll ich das image draufbekommen, ftp läuft ja nicht.
-
Ich habe jetzt 'dreambox-image-dm7080.tar.xz' selbst runtergeladen und geflashed, was auch problemlos durchgelaufen ist, aber nach dem reboot fährt die box wieder selbstständig in den recovery modus. Was kann ich tun?
telnet connect geht noch -
meine box bootet seid dem update leider auch nicht!!
Online Recovery bleibt immer bei "initiating reboot" hängen, wenn ich die Box manuell neustarte fährt sie automatisch wieder in den flash modus hoch, obwohl ich nicht den Power Knopf gehalten habe.
[size=0][*] Mounting root filesystem[/size][*] Extracting 'dreambox-image-dm7080.tar.xz' to '/mnt'
[*] Flashing boot image
[*] Creating boot image
[*] Flashing boot image
[*] Enabling boot source A
[*] Unmounting '/mnt/dev'
[*] Unmounting '/mnt/proc'
[*] Unmounting '/mnt/run'
[*] Unmounting '/mnt/sys'
[*] Unmounting '/mnt/tmp'
[*] Unmounting '/mnt'
[*] Unmounting '/data'
[*] Initiating rebootKann man irgendwo das originale image ziehen, damit ich es sauber flashen kann oder gibt es noch etwas was ich tun kann?