Ich hatte mich heute nochmal an die Dreambox gemacht und ich hatte sie dann irgendwann zum laufen bekommen.
Aber das war nicht von langer dauer. Nach einem ausschalten und wieder einschalten hing sie wieder bei "/flash/vmlinux.gz"
Diesmal hab ich nochmal ein Bootlog erstellt mit aktiviertem Debug Mode.
Dreambox DM7025
FIRST STAGE 1.4 {2345}
2ND STAGE OK, build #76 (20091202)
0.000 - DM7025 board setup
0.002 - initializing PCI...
0.013 - done!
0.015 - fp init
FP version 7 detected
0.102 - ca init
RSA key 1 is used.
0.207 - load config
0.786 - config loaded.
* press [S] to enter setup
BUS DEV FUN
--------------------------------------------------
0 a 0 10ec 8139 Ethernet controller
0 14 0 1002 4865 Other multimedia device
0 14 1 1002 4866 IDE controller
0 14 2 1002 4867 Universal Serial Bus
0 14 5 1002 4868 Audio device
0 14 6 1002 4869 Modem
0.830 - ide init
0.831 - IDE found on PCI0:00a1 IO 2210
no CF card detected!
no OLED found!
BOOT #76(20091202)
0.961 - NAND PROBE: 10 10 10 10
0.964 - NAND: trying highspeed...
0.968 - NAND PROBE: ad 75 a5 00 (HS)
0.971 - main control
0.974 - not entering setup
0.976 - force boot: -1
0.979 - try boot from 1:
0.981 - execute script: /flash/autoexec.bat
0.986 - load /flash/autoexec.bat to 834dae28
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
1.933 - jffs2 size: 3840 kb
1.936 - network: 1.938 manual, ip address is 10.14.11.10
2.003 - starting network
2.005 - httpd, telnetd, dreamupd
dreamupd initialized
2.011 - ok. start receiving packets
2.014 - starting dhcp (or manual)
2.018 - network: 2.019 manual, ip address is 10.14.11.10
2.072 - dhcp started!
2.075 - using jffs2
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
2.240 - load /flash/bootlogo.elf to 82000000
2.244 - using jffs2
2.256 - loading elf image at 82000000
2.268 - jumping to 80401810
2.271 - load /cf/bootlogo.mvi to a2800100
2.275 - load /flash/bootlogo.mvi to a2800100
2.280 - using jffs2
vscale: 576:576
/flash/vmlinux.gz
2.398 - load /flash/vmlinux.gz to 82000000
2.403 - using jffs2
2.600 - decompressing elf (compressed: 2119262 bytes)
3.250 - decompression ok (uncompressed: 5315533 bytes)
3.284 * Quiesce...
3.286 *** Turning off USB
3.289 *** Quiesce network...
3.303 - loading elf image at 80800000
3.408 - jumping to 804fe000
LINUX started...
ATI Xilleon 226 (little endian), Solo mode
PCI bus speed is 33MHz
Initializing IRQs
about to enable interrupts!
interrupts enabled.
Alles anzeigen
Für mich sieht das aus, als ob sie Problemlos bis zum Booten von Linux durchläuft.
Aber vielleicht sieht jemand von euch noch ein Problem.
An was kann es also liegen? Am Image selbst?
Müsste sie, wenn es denn am Netzteil liegen sollte, nicht schon früher aussteigen oder überhaupt nichts mehr von sich geben?
Könnte vielleicht mal einer von euch die Spannungen an dem Motherboard messen von einer Box die keine Probleme hat?
Dann könnte man das Netzteil vielleicht schon ausschließen.