Ich wollte eine manual scan machen weil in die Niederlande einige Sender mit 8PSK gestartet sind. Wenn ich in das Schirm die modulation betätige crashed Enigma2.
Update: mit Dreamset die Einstellungen fur die Transponder auf 8PSK eingestellt und nach die DM8000 gesendet. Dann wird die Sender wiedergeben und Anpassung vom Modulation ergibt auch kein Crash mehr.
Die Sender: Film1 Premiere HD, 12129 V 27500 2/3 DVB-S2 8PSK
Gestern ist die Box zwei mal hangen geblieben und ich denke um denke daran um nach die 3.1 Version zurück zu gehen. Ich muss die box dann box mit die Stromschalter abschalten weil ich nicht immer eine Computer an habe um init 4 und init 5 zu senden.
Die Harddisk findet die Notabschaltung nicht gut und macht das bemerkbar mit einem laute klick weil die DM8000 noch immer zugriff hat auf de Disk. 
Ich hoffe das die 3.21 update auch ein anderes Problem mit dem deep standby lost: http://www.dream-multimedia-tv.de/board/index.php?page=Thread&threadID=15762
Eine ganze weile ging es gut aber heute morgen nach eine Aufnahme mit deep standby danach hangt die box wieder in und geht nicht in die die deep standby. Ich habe nur die dmesg und ein log wenn ich jetzt auf die an/aus knopf drucke:
dmesg:
[24010.804000] bcm4506: signal_strength -250.03dbm
[24011.829000] bcm4506: signal_strength -249.97dbm
[24012.854000] bcm4506: signal_strength -251.67dbm
[24013.907000] stop pcr0 on dmx 3 pid:80d
[24013.912000] stop video0 on dmx 3 pid:80d
[24013.917000] VIDEO0: stop decode
[24013.920000] VIDEO0: set blank to 1
[24013.924000] audio: decoder stop
[24013.941000] stop audio on dmx 3 pid:80e
[24013.945000] audio: xpt stop(2)
[24013.949000] no decoder left in sync handling so disable xpt_sync
[24013.954000] bcm_audio_channel_stop(2) done
[24013.986000] bcm4501: channel 0 is in normale mode now
[24014.795000] start pcr0 on dmx 2 pid:205 index 11
[24014.800000] start audio on dmx 2 pid:5a
[24014.806000] audio xpt start
[24014.809000] sync is off so we enable it
[24014.813000] demux-index 2 pcr0pid 205
[24014.817000] using 11 as pcr0 pidchannel
[24014.822000] MPEG
[24014.824000] audio: decoder start 0
[24014.842000] video delay 0 (0 ms)
[24014.845000] total video delay: 0 (0 ms)
[24014.850000] VIDEO0: set streamtype!
[24014.853000] set H264
[24014.856000] sw rave disabled!
[24014.859000] audio delay 18000 (200 ms)
[24014.864000] total video delay: 18000 (200 ms)
[24014.868000] start video0 on dmx 2 pid:205
[24014.873000] total video delay: 18000 (200 ms)
[24014.879000] VIDEO0: start decode
[24015.038000] bcm_audio: use saved pts 0x1aee4afc2 (0x0) (ret 0)
[24015.045000] audio: decoder stop
[24015.061000] stop audio on dmx 2 pid:5a
[24015.066000] audio: xpt stop(9)
[24015.069000] bcm_audio_channel_stop(9) done
[24015.073000] start audio on dmx 2 pid:5c
[24015.077000] audio xpt start
[24015.081000] AC3
[24015.083000] audio: streamtype set 1
[24015.087000] audio: streamtype_set: stop rave
[24015.091000] decode
[24015.094000] audio: streamtype_set: restart rave
[24015.099000] set mute 0 (111) 0
[24015.101000] audio: decoder start 0
[24015.119000] audio delay 18000 (200 ms)
[24015.122000] total video delay: 18000 (200 ms)
[24015.590000] ch0: lock
[24015.592000] RAP first pts 0x10e89dd6a, stc 0x10e89d69c, pcr valid
[24015.619000] ch0: lock
[24015.652000] ch0: lock
[24015.681000] ch0: lock
[24015.716000] ch0: lock
[24015.743000] ch0: lock
[24016.052000] printk: 2 messages suppressed.
[24016.056000] RAP sampling rate info isr
[24016.059000] eModeChange Isr.. set source_changed_event!
[24016.585000] VIDEO0: first pts 0x10e8d29c0
[24016.589000] VIDEO0: resolution changed (1920 1080)
[24016.593000] VIDEO0: aspect changed 3
[24016.595000] set current avs auto aspect to 16:9
[24016.600000] disable wss on display 0
[24016.602000] set wss 7 on display 1
[24016.605000] set sb to 3(1)
[24016.739000] enable tsm0
[24025.782000] bcmfb: disable manual blit
[24026.031000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
[24026.208000] disable wss on display 0
[24026.211000] set wss 7 on display 1
[24026.227000] set sb to 1(1)
[24026.325000] set current avs auto aspect to 16:9
[24026.330000] disable wss on display 0
[24026.334000] set wss 7 on display 1
[24026.338000] set sb to 1(1)
[24026.344000] set current avs auto aspect to 16:9
[24026.349000] disable wss on display 0
[24026.353000] set wss 7 on display 1
[24026.356000] set sb to 1(1)
[24026.360000] VIDEO0: dst_left, dst_top, dst_width and dst_height is 0.. reset to defaults!
[24026.369000] set current avs auto aspect to 16:9
[24026.374000] disable wss on display 0
[24026.378000] set wss 7 on display 1
[24026.381000] set sb to 1(1)
[24026.385000] set sb to 1(1)
[24026.387000] disable wss on display 0
[24026.391000] set wss 7 on display 1
[24088.299000] set sb to 3(1)
[24088.302000] disable wss on display 0
[24088.306000] set wss 7 on display 1
[24088.360000] bcmfb: enable manual blit
[24088.382000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
[24852.640000] bcm4506: channel 0 is sleeping now
[24868.960000] stop pcr0 on dmx 2 pid:205
[24868.965000] stop video0 on dmx 2 pid:205
[24868.969000] VIDEO0: stop decode
[24868.972000] VIDEO0: set blank to 1
[24868.977000] audio: decoder stop
[24868.994000] stop audio on dmx 2 pid:5c
[24868.998000] audio: xpt stop(12)
[24869.002000] no decoder left in sync handling so disable xpt_sync
[24869.007000] bcm_audio_channel_stop(12) done
[24879.492000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
[24879.522000] bcmfb: disable manual blit
[52266.562000] HDMI: hotplug handler!
[52266.566000] HDMI: no device attached
[52266.712000] HDMI: hotplug handler!
[52266.754000] using 50.00Hz as MonitorRefreshRate
[52266.874000] SET FORMAT: display[0], format=27
[52266.879000] HDMI detected
[52266.881000] HDMI mode
[52266.884000] use EDID to detect colorspace
[52266.888000] using colorspace: 1
[52266.989000] bcm_video_analog_port_setup (fmt=7)
[52267.094000] SET FORMAT: display[1], format=7
[52267.214000] set current avs auto aspect to 16:9
[52267.219000] disable wss on display 0
[52267.222000] set wss 7 on display 1
[52267.226000] set sb to 3(1)
Log:
[52898.477000] keys 83
[52898.708000] keys 87
[52913.180000] keys 83
[52913.499000] keys 87
[52914.546000] keys 83
[52914.769000] keys 87
[52915.632000] keys 83
[52916.431000] keys 87
[52917.374000] keys 83
[52917.621000] keys 87
[52918.268000] keys 83
[52918.459000] keys 87
[52919.090000] keys 83
[52919.209000] keys 87
[52919.728000] keys 83
[52919.903000] keys 87
[52920.822000] keys 83
[52920.997000] keys 87
[52921.604000] keys 83
[52921.787000] keys 87
Also nichts passiert!!!!!!
init 4 und dan init 3:
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
[53039.369000] bcm4501: channel 0 is sleeping now
INIT: no more processes left in this runlevel
INIT: Switching to runlevel: 3
system message bus already started; not starting.
Starting system message bus: /usr/bin/dbus-daemon is already running
614
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[A[74G[ ok ]
[53049.547000] VIDEO0: set streamtype!
[53049.550000] set MPEG2
[53049.552000] sw rave disabled!
[53049.555000] VIDEO0: set blank to 0
[53049.559000] sync is off so we enable it
[53049.564000] playback!
[53049.566000] total video delay: 0 (0 ms)
[53049.570000] VIDEO0: start decode
[53049.574000] flush video decoder
[53049.577000] VIDEO0 use saved pts 0x1131d8110 (ret 0)
[53049.635000] VIDEO0: first pts 0x0
[53049.638000] VIDEO0: resolution changed (1280 720)
[53049.739000] VIDEO0: set blank to 0
[53049.742000] VIDEO0: stop decode
[53049.745000] VIDEO0: set blank to 0
[53049.749000] no decoder left in sync handling so disable xpt_sync
[53050.589000] VIDEO0: progressive changed (1)
Epg.dat found at : /media/cf/epg.dat
newepg found at : None
setenv('prefix', '/usr', 0)
setenv('exec_prefix', '/usr', 0)
setenv('bindir', '/usr/bin', 0)
setenv('sbindir', '/usr/sbin', 0)
setenv('libexecdir', '/usr/libexec', 0)
setenv('datarootdir', '${prefix}/share', 0)
setenv('datadir', '/usr/share', 0)
setenv('sysconfdir', '/etc', 0)
setenv('sharedstatedir', '/com', 0)
setenv('localstatedir', '/var', 0)
setenv('libdir', '/usr/lib', 0)
setenv('localedir', '${datarootdir}/locale', 0)
setenv('prefix', '/usr', 1)
setenv('exec_prefix', '/usr', 1)
setenv('bindir', '/usr/bin', 1)
setenv('sbindir', '/usr/sbin', 1)
setenv('libexecdir', '/usr/libexec', 1)
setenv('datarootdir', '/usr/share', 1)
setenv('datadir', '/usr/share', 1)
setenv('sysconfdir', '/etc', 1)
setenv('sharedstatedir', '/com', 1)
setenv('localstatedir', '/var', 1)
setenv('libdir', '/usr/lib', 1)
setenv('localedir', '/usr/share/locale', 1)
resolve: resolve ${datadir}/enigma2/encoding.conf
resolve: -> /usr/share/enigma2/encoding.conf
resolve: resolve ${libdir}/enigma2/python
resolve: -> /usr/lib/enigma2/python
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (8) graphics acceleration manager
+ (9) GFBDC
16384k video mem
[53053.548000] bcmfb: enable manual blit
[53053.555000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
- double buffering available!
.
.
.
Und ich habe wieder eine functionierende Dreambox 8000s bis dem nächste mail bis er wieder crashed!?!??!?
update: bootlog vom eine deep standby danach attached.
Alles anzeigenMein Box hing auch schon ein paar mal mit der Option "Neustart"
Weder Display oder LED waren zu sehen. Nur Festplatte und Lüfter liefen weiter.
Nach einem Softwareuptat zB. startet die Box ohne probleme
.... und nein ein Log hab ich nicht
Welche Version hat du jetzt?
Im 3.2 Image lässt sich das DVD Laufwerk meiner 8k nicht mehr drosseln.
Wenn du GP3 gebraucht dann blau - Device Manager - geh nach DVD player und drucke noch mal blau - setup - speed = 100 - save
Bemerkung, 0 = nicht gedrosselt und 128 ist ganz gedrosselt.
Meine DM8000 mit dem Release dm8000-3.2.0 ist gestern auch einfach ausgegangen nachdem ich kurz den an/aus Schalter vorn betätigt habe. Box war im Standby und ich wollte sie vorne über den an/aus Schalter einschalten. Sie ist aber nicht runtergefahren sondern gleich aus gegangen.
Mfg
Stand auf dem Moment noch etwas noch in die Display vom der Dreambox oder war er schwarz?
Jetzt ein log von dat nich ausschalten und mein init 4 am ende:
have 1 video stream(s) (0206), and 1 audio stream(s) (005a), and the pcr pid is 1ffe, and the text pid is 0026
decoder state: play, vpid=518, apid=90
[eDVBCAService] new service 1:0:1:7D6:449:35:C00000:0:0:0:
[eDVBCAService] add demux 3 to slot 0 service 1:0:1:7D6:449:35:C00000:0:0:0:
[eDVBCIInterfaces] gotPMT
demux 3 mask 08 prevhash 00000000
[eDVBCAService] send 148 bytes
9f 80 32 81 8f 03 07 d6 3d 00 22 01 81 08 00 c0 00 00 04 49 00 35 82 02 08 03 84 02 07 d6 09 04 06 22 e5 6d 09 07 18 17 e7 11 02 00 6a 02 02 06 00 27 01 09 11 01 00 e6 49 00 6a ff 00 08 00 00 00 00 02 04 2b 62 09 11 01 00 e7 11 00 6a ff ff e0 00 00 00 00 00 00 2b 62 04 00 5a 00 27 01 09 11 01 00 e6 49 00 6a ff 00 08 00 00 00 00 02 04 2b 62 09 11 01 00 e7 11 00 6a ff ff e0 00 00 00 00 00 00 2b 62 06 00 26 00 00 c0 00 d0 00 00 c1 00 fa 00 00
doing version filtering
07d6: 02 07 d6 3d 00 00
mask: ff ff ff 3f 00 00
mode: 00 00 00 3e 00 00
[FanControl2] Vlt:100 Pwm:140 Fan:4pin - BoxOn HDDon
[4294885.827000] ch0: lock
[FanControl2] currentRPM:0 targetRPM:697 Temp:40.5
-+ 1/2 TID 4e
[SEC] set dynamic current limiting
[4294885.970000] RAP first pts 0x13a4d058e, stc 0x13a4cf62e, pcr valid
[4294886.065000] printk: 5 messages suppressed.
[4294886.070000] RAP sampling rate info isr
[4294886.073000] eBitRateChange Isr.. set source_changed_event!
[4294886.077000] eModeChange Isr.. set source_changed_event!
[4294886.172000] VIDEO0: first pts 0x13a4ddf00
[4294886.326000] enable tsm0
++ 2/2 TID 4e
done!
doing version filtering
0012: 4e 07 d6 2f 00 00
mask: ff ff ff 3f 00 00
mode: 00 00 00 3e 00 00
sdt update done!
[EPGC] start caching events(1320246578)
It's now Wed Nov 2 16:09:39 2011
[timer.py] next activation: 1320246679 (in 99998 ms)
It's now Wed Nov 2 16:09:39 2011
[timer.py] next activation: 1320246679 (in 99996 ms)
[AutoRes] determineContent
[AutoRes] switch deinterlacer mode to on
[AutoRes] new content is 704x576i25
[AutoRes] determined videomode 1080i
[eDVBLocalTimerHandler] diff is 0
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] not changed
[4294893.888000] keys 83
action -> GlobalActions power_down
nr_read 115 nr_write 1
sum 116 prev_sum 116
hdd IDLE!
[IDLE] 59.9999160767 600 False
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail viasat reading
action -> GlobalActions deepstandby
PowerOff - Now!
[4294894.919000] keys 87
Looking for embedded skin
action -> GlobalActions power_up
[EPGImport] Will wake up from deep sleep
[EPGImport] WakeUpTime now set to -1 (now=1320246585)
stopService
[eDVBCAService] free slot 0 demux 3 for service 1:0:1:7D6:449:35:C00000:0:0:0:
[eDVBCAService] free service 1:0:1:7D6:449:35:C00000:0:0:0:
decoder state: p[4294895.058000] stop pcr0 on dmx 3 pid:1ffe
lay, vpid=-1, ap[4294895.063000] stop video0 on dmx 3 pid:206
id=-1
DEMUX_STOP - pcr - ok
DE[4294895.069000] VIDEO0: stop decode
MUX_STOP - video[4294895.073000] VIDEO0: set blank to 1
- ok
VIDEO_STO[4294895.077000] audio: decoder stop
P - ok
AUDIO_STOP - ok[4294895.094000] stop audio on dmx 3 pid:5a
DEMUX_STOP - a[4294895.098000] audio: xpt stop(3)
udio - [4294895.102000] no decoder left in sync handling so disable xpt_sync
[4294895.107000] bcm_audio_channel_stop(3) done
ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
start release channel timer
[EPGImport] autostart (1) occured at 1320246585.9
[EPGImport] Stop
resolve: resolve ${sysconfdir}/enigma2/lamedb
resolve: -> /etc/enigma2/lamedb
---- saving lame channel db
saved 1060 channels and 14187 services!
release cached channel (timer timeout)
[eDVBCAService] remove channel 0xd14390
[eDVBLocalTimerHandler] remove channel 0xd14390
[eEPGCache] remove channel 0xd14390
[EPGC] abort caching events !!
stop release channel timer
[EPGC] store epg to realpath '/media/cf/epg.dat'
[EPGC] 5653 events written to /media/cf/epg.dat
thread joined 0
set RTC to previous valid time
- (41) eServiceFactoryM2TS
- (41) eServiceFactoryMP3
- (41) eServiceFactoryFS
- (41) eServiceFactoryDVB
- (41) eServiceFacto[4294897.869000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
ryTS
- (41) eServiceFactoryDVD
- (40) eService[4294897.887000] bcmfb: disable manual blit
Center
- (35) CI Slots
- (30) eActionMap
- (21) input device driver
- (21) Console RC Driver
- (20) DVB-CI UI
- (20) UHF Modulator
- (20) RC Input layer
- (20) misc options
- (20) AVSwitch Driver
- (15) eWindowStyleManager
- (10) gRC
waiting for gRC thread shutdown
gRC thread has finished
- (9) GFBDC
- (9) gLCDDC
- (9) Font Render Class
- (8) graphics acceleration manager
- (5) gBackground
- (5) geminimain
[gUtils] save Config /etc/enigma2/gemini_plugin.conf
[gMain] stopped
thread joined 0
- (1) Background File Eraser
- (1) ghardware
send cancel to thread
thread joined 0
[gHardware] stopped...
reached rl -1
close frontend 0
[prepareClose] no mainloop
[SEC] setTone 0
[SEC] sleep 25ms
set sequence pos 5
[SEC] delayed close frontend
close frontend 0
[4294898.912000] bcm4501: channel 0 is sleeping now
INIT:
INIT: Sending stopping gdaemon... stopped gdaemon (pid 725)
done.
Stopping Dropbear SSH server: stopped /usr/sbin/dropbear (pid 733)
dropbear.
Stopping automounter: done.
* Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon
[A[74G[ ok ]
stopping Busybox Periodic Command Scheduler: crond... stopped crond (pid 739)
done.
Stopping system message bus: stopped process in pidfile '/var/run/dbus/pid' (pid 605)
dbus.
stopping gMailCheck... stopped gMailCheck (pid 741)
done.
Stopping internet superserver: inetd.
Stopping syslogd/klogd: stopped syslogd (pid 747)
stopped klogd (pid 749)
done
* stopping FTP Server: vsftpd... no /usr/sbin/vsftpd found; none killed
Deconfiguring network interfaces... Unmounting remote filesystems...
Unmounting other remote filesystems...
killall: smbd: no process killed
killall: nmbd: no process killed
Unmounting remote filesystems...
Unmounting other remote filesystems...
done.
Sending all processes the TERM signal...
Sending all processes the KILL signal...
Deactivating swap...
Unmounting local filesystems...
mount: can't find /mnt/ram in /proc/mounts
umount: udev busy - remounted read-only
umount: sysfs busy - remounted read-only
mount: cannot read /proc/mounts: No such file or directory
[4294920.565000] Synchronizing SCSI cache for disk sda:
[4294920.570000] Power down.
[4294920.573000] fp_power_off
[ 5834.281000] keys 83
action -> GlobalActions power_down
action -> GlobalActions deepstandby
PowerOff - Now!
Looking for embedded skin
[EPGImport] Will wake up from deep sleep
[EPGImport] WakeUpTime now set to -1 (now=1320269986)
stopService
[eDVBCAService] free slot 0 demux 3 for service 1:0:1:24:11:85:C00000:0:0:0:
[eDVBCAService] free service 1:0:1:24:11:85:C00000:0:0:0:
decoder state: p[ 5835.469000] stop pcr0 on dmx 3 pid:3ff
lay, vpid=-1, ap[ 5835.474000] stop video0 on dmx 3 pid:3ff
id=-1
DEMUX_STOP - pcr - ok
DE[ 5835.479000] VIDEO0: stop decode
MUX_STOP - video[ 5835.483000] VIDEO0: set blank to 1
- ok
VIDEO_STO[ 5835.487000] audio: decoder stop
P - ok
AUDIO_STOP - [ 5835.499000] keys 87
ok[ 5835.504000] stop audio on dmx 3 pid:401
DEMUX_STOP - a[ 5835.508000] audio: xpt stop(3)
udio - [ 5835.511000] no decoder left in sync handling so disable xpt_sync
[ 5835.517000] bcm_audio_channel_stop(3) done
ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
start release channel timer
[EPGImport] autostart (1) occured at 1320269987.03
[EPGImport] Stop
resolve: resolve ${sysconfdir}/enigma2/lamedb
resolve: -> /etc/enigma2/lamedb
---- saving lame channel db
saved 1060 channels and 14187 services!
release cached channel (timer timeout)
[eDVBCAService] remove channel 0x3054ad80
[eDVBLocalTimerHandler] remove channel 0x3054ad80
[eEPGCache] remove channel 0x3054ad80
stop release channel timer
[EPGC] store epg to realpath '/media/cf/epg.dat'
[EPGC] 12516 events written to /media/cf/epg.dat
thread joined 0
set RTC to previous valid time
- (41) eServiceFactoryM2TS
- (41) eServiceFactoryMP3
- (41) eServiceFactoryFS
- (41) eServiceFactoryDVB
- (41) eServiceFactoryTS
- (41) eServiceFactoryDVD
[ 5839.223000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
- (40) eServiceCenter
- (35) CI Slots
- (30) [ 5839.241000] bcmfb: disable manual blit
eActionMap
- (21) input device driver
- (21) Console RC Driver
- (20) DVB-CI UI
- (20) UHF Modulator
- (20) RC Input layer
- (20) misc options
- (20) AVSwitch Driver
- (15) eWindowStyleManager
- (10) gRC
waiting for gRC thread shutdown
gRC thread has finished
- (9) GFBDC
- (9) gLCDDC
- (9) Font Render Class
- (8) graphics acceleration manager
- (5) gBackground
- (5) geminimain
[gUtils] save Config /etc/enigma2/gemini_plugin.conf
[gMain] stopped
thread joined 0
- (1) Background File Eraser
- (1) ghardware
send cancel to thread
thread joined 0
[gHardware] stopped...
reached rl -1
close frontend 0
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
[ 5975.139000] bcm4501: channel 0 is sleeping now
INIT: no more processes left in this runlevel
Und init 3
INIT: Switching to runlevel: 3
system message bus already started; not starting.
Starting system message bus: /usr/bin/dbus-daemon is already running
615
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[A[74G[ ok ]
[ 6399.756000] VIDEO0: set blank to 0
[ 6399.759000] sync is off so we enable it
[ 6399.763000] playback!
[ 6399.765000] total video delay: 0 (0 ms)
[ 6399.768000] VIDEO0: start decode
[ 6399.772000] flush video decoder
[ 6399.776000] VIDEO0 use saved pts 0x1c046ebd6 (ret 0)
[ 6399.831000] VIDEO0: first pts 0x0
[ 6399.834000] VIDEO0: resolution changed (1280 720)
[ 6399.940000] VIDEO0: set blank to 0
[ 6399.943000] VIDEO0: stop decode
[ 6399.946000] VIDEO0: set blank to 0
[ 6399.949000] no decoder left in sync handling so disable xpt_sync
setenv('prefix', '/usr', 0)
setenv('exec_prefix', '/usr', 0)
setenv('bindir', '/usr/bin', 0)
setenv('sbindir', '/usr/sbin', 0)
setenv('libexecdir', '/usr/libexec', 0)
setenv('datarootdir', '${prefix}/share', 0)
setenv('datadir', '/usr/share', 0)
setenv('sysconfdir', '/etc', 0)
setenv('sharedstatedir', '/com', 0)
setenv('localstatedir', '/var', 0)
setenv('libdir', '/usr/lib', 0)
setenv('localedir', '${datarootdir}/locale', 0)
setenv('prefix', '/usr', 1)
setenv('exec_prefix', '/usr', 1)
setenv('bindir', '/usr/bin', 1)
setenv('sbindir', '/usr/sbin', 1)
setenv('libexecdir', '/usr/libexec', 1)
setenv('datarootdir', '/usr/share', 1)
setenv('datadir', '/usr/share', 1)
setenv('sysconfdir', '/etc', 1)
setenv('sharedstatedir', '/com', 1)
setenv('localstatedir', '/var', 1)
setenv('libdir', '/usr/lib', 1)
setenv('localedir', '/usr/share/locale', 1)
resolve: resolve ${datadir}/enigma2/encoding.conf
resolve: -> /usr/share/enigma2/encoding.conf
resolve: resolve ${libdir}/enigma2/python
resolve: -> /usr/lib/enigma2/python
PYTHONPATH: /usr/lib/enigma2/python
[ 6400.785000] VIDEO0: progressive changed (1)
+ (1) Background File Eraser
+ (8) graphics acceleration manager
+ (9) GFBDC
16384k video mem
[ 6401.012000] bcmfb: enable manual blit
Heute Abend aber leider kein log.
Mit dem an/aus schalter die box abgeschaltet aber die box fahrt nicht runter. Kein blue led und auch nichts in die display. Box mit init 4 und dann init 3 wieder belebt und dann war es möglich die box ganz runter zu fahren.
update: dies ist nur einmal vorgekommen.
Abschalten von der Dreambox geht zu schnell bei betatigen von der an/aus schalter vorne:
[EPGC] start cleanloop
[EPGC] stop cleanloop
[EPGC] 197049 bytes for cache used
[FanControl2] Reread
[FanControl2] Reread
[FanControl2] Vlt:100 Pwm:130 Fan:4pin - BoxOn HDDon
[FanControl2] currentRPM:0 targetRPM:675 Temp:40.0
[FanControl2] Reread
[4294881.117000] keys 83
BCM97400
AB
FFFFFFFF
1s
Sync=0
LLMB=0
L2=0
RAC_I=0
RAC_D=0
Copy Code...34TUCV
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox D M8000
FIRST STAGE 1.00 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-01)
0.000 - BCM board setup
Configure MEMC1_2........ Done
0.039 - fp init
FP version 7 detected
0.106 - ca init
0.823 - load config
1.403 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #84
- NAND PROBE: 2c da 80 15 (normal)
Hier auch das Problem seit dem vorletztem experimetal und jetzt auch mit dem 3.2 zweitem update. Zeit dem zweitem update habe ich auf ein bootlogo an Anfang. Jetzt bleibt der box noch oft hangen wenn er in deep-standby geht.
Ich werde mal ein computer bauen und anschließen um das log zu generieren wenn de box hangen bleibt.
Thanks for reverting to the previous version. 
dreambox-dvb-modules.bb: update dm800/dm800se/dm500hd/dm8000 hardware drivers
- reentrancy fixes in demux and video/audio clip mode (fixed frequently kernel oops)
- fixed not visible PEP options on DM8000
- revert to previous video output, hdmi and video decoder code (DM500HD/DM800SE/DM8000)
this should fix some problems introduced with 20110215 drivers
- added pcr/hdmi kernel debug output messages to debug hdmi problems (DM800)
The dmesg result if the same recording is playing in the old driver version:
[ 467.827000] dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
[ 467.838000] start audio on dmx 4 pid:209
[ 467.843000] audio xpt start
[ 467.847000] sync is off so we enable it
[ 467.852000] playback!
[ 467.856000] MPEG
[ 467.859000] audio: decoder start 0
[ 467.879000] audio delay 2250 (25 ms)
[ 467.883000] total video delay: 0 (0 ms)
[ 467.886000] ch0: lock
[ 467.886000] RAP first pts 0x1aa14ddd8, stc 0x1acf5b606, pcr invalid
[ 467.898000] start video0 on dmx 4 pid:208
[ 467.902000] total video delay: 0 (0 ms)
[ 467.909000] VIDEO0: start decode
[ 467.917000] PVR flush
[ 467.920000] flush audio decode
[ 467.939000] VIDEO0: first pts 0x1aa1b43c0
[ 467.949000] audio delay 2250 (25 ms)
[ 467.953000] total video delay: 0 (0 ms)
[ 467.958000] flush video decoder
[ 467.968000] ch0: lock
[ 467.972000] RAP first pts 0x1aa10e958, stc 0x1aa1b20d0, pcr invalid
[ 467.977000] video_stc is not valid yet.. so ignore audio first pts
[ 467.982000] VIDEO0: first pts 0x1aa122560
[ 467.987000] printk: 38 messages suppressed.
[ 467.991000] RAP pts error 0 PTS 0xd508f33c, STC 0xd508fc4b, type 0
[ 468.011000] RAP sampling rate info isr
[ 468.015000] eBitRateChange Isr.. set source_changed_event!
[ 468.020000] eModeChange Isr.. set source_changed_event!
[ 468.067000] dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
[ 468.148000] enable tsm0
The picture playback doesn't stop after a few seconds.
Screen when I run enigma2.sh
playing 1:0:0:0:0:0:0:0:0:0:xyz.ts
alloc PVR
allocate demux
loading streaminfo for xyz.ts
loading cuts..
0 entries
before: 1
after: 1
setIoPrio best-effort level 0 ok
FILEPUSH THREAD START
getNextSourceSpan, current offset is 00000000, m_skipmode_m = 0!
NO CUESHEET. (00000000, 10485700)
no version filtering
0012: 4e 00 00 00 00 00
mask: ff ff ff 00 00 00
mode: 00 00 00 00 00 00
ok ... now we start!!
no version filtering
0000: 00 00 00 00 00 00
mask: ff 00 00 00 00 00
mode: 00 00 00 00 00 00
eventNewProgramInfo 0 0
have 1 video stream(s) (0208), and 1 audio stream(s) (0209), and the pcr pid is 0208, and the text pid is ffffffff
disable teletext subtitles
PES filter: DMX_SET_PES_FILTER - Invalid argument
decoder state: play, vpid=520, apid=521
DMX_SET_PES_FILTER(0x209) - audio - ok
DEMUX_START - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PAUSE - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux4
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x208) - video - ok
DEMUX_START - video - ok
VIDEO_FREEZE - ok
VIDEO_PLAY - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
VIDEO_CONTINUE - ok
AUDIO_CONTINUE - ok
eDVBServicePlay::seekTo: jump 0
seek.
stopping thread.
FILEPUSH THREAD STOP
thread joined 0
AUDIO_CLEAR_BUFFER - ok
VIDEO_CLEAR_BUFFER - ok
before: 1
after: 1
setIoPrio best-effort level 0 ok
FILEPUSH THREAD START
getNextSourceSpan, current offset is 0017f580, m_skipmode_m = 0!
getOffset for pts 0x0
ok, resolved skip (rel: 0, diff 0), now at 00000000
NO CUESHEET. (00000000, 10485700)
new service started! trying to download cuts!
RemovePopup, id = ZapError
+ 1/1 TID 00
done!
PATready
use pmtpid 020a for service_id 1274
no version filtering
020a: 02 12 74 00 00 00
mask: ff ff ff 00 00 00
mode: 00 00 00 00 00 00
doing version filtering
0000: 00 00 00 2b 00 00
mask: ff 00 00 3f 00 00
mode: 00 00 00 3e 00 00
VIDEO_GET_EVENT - ok
+ 1/1 TID 02
done!
eventNewProgramInfo 0 0
have 1 video stream(s) (0208), and 1 audio stream(s) (0209), and the pcr pid is 0208, and the text pid is ffffffff
PES filter: DMX_SET_PES_FILTER - Invalid argument
decoder state: play, vpid=520, apid=521
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
VIDEO_CONTINUE - ok
AUDIO_CONTINUE - ok
doing version filtering
020a: 02 12 74 07 00 00
mask: ff ff ff 3f 00 00
mode: 00 00 00 3e 00 00
timeout 0012!
action -> MoviePlayerActions leavePlayer
reused converter!
reused converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
warning, skin is missing element freeDiskSpace in <class 'Screens.MovieSelection.MovieSelection'>
warning, skin is missing element description in <class 'Screens.MovieSelection.MovieSelection'>
warning, skin is missing element Video in <class 'Screens.MovieSelection.MovieSelection'>
warning, skin is missing element date in <class 'Screens.MovieSelection.MovieSelection'>
warning, skin is missing element moviemenutext in <class 'Screens.MovieSelection.MovieSelection'>
warning, skin is missing element channel in <class 'Screens.MovieSelection.MovieSelection'>
halign must be either left, center, right or block!
stopService
stopping thread.
FILEPUSH THREAD STOP
thread joined 0
service end!
resolved to PLAY
eDVBServicePlay::unpause
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
This is the dmesg when I play the movie.
[ 9712.526000] dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
[ 9712.536000] start audio on dmx 4 pid:209
[ 9712.541000] audio xpt start
[ 9712.544000] sync is off so we enable it
[ 9712.548000] playback!
[ 9712.551000] MPEG
[ 9712.553000] audio: decoder start 0
[ 9712.571000] audio delay 2250 (25 ms)
[ 9712.575000] total video delay: 0 (0 ms)
[ 9712.579000] ch0: lock
[ 9712.582000] RAP first pts 0x1aa141358, stc 0x1aa758842, pcr invalid
[ 9712.590000] start video0 on dmx 4 pid:208
[ 9712.595000] total video delay: 0 (0 ms)
[ 9712.604000] VIDEO0: start decode
[ 9712.613000] flush audio decode
[ 9712.632000] VIDEO0: first pts 0x1aa1a1c70
[ 9712.648000] audio delay 2250 (25 ms)
[ 9712.651000] total video delay: 0 (0 ms)
[ 9712.656000] flush video decoder
[ 9712.669000] ch0: lock
[ 9712.672000] RAP first pts 0x1aa10e958, stc 0x1aa19fcfe, pcr invalid
[ 9712.677000] video_stc is not valid yet.. so ignore audio first pts
[ 9712.685000] VIDEO0: first pts 0x1aa122560
[ 9712.690000] printk: 43 messages suppressed.
[ 9712.694000] RAP pts error 0 PTS 0xd508f33c, STC 0xd508fc3e, type 0
[ 9712.714000] RAP sampling rate info isr
[ 9712.719000] eBitRateChange Isr.. set source_changed_event!
[ 9712.723000] eModeChange Isr.. set source_changed_event!
[ 9712.819000] dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
[ 9712.849000] enable tsm0
[ 9713.777000] XVD pts error PTS 0xd5128c78, STC 0xd509bc7b, type 0
[ 9713.796000] XVD pts error PTS 0xd5128c78, STC 0xd509c000, type 0
[ 9713.815000] XVD pts error PTS 0xd5128c78, STC 0xd509c383, type 0
[ 9713.835000] XVD pts error PTS 0xd512a898, STC 0xd509c70b, type 0
[ 9713.874000] XVD pts error PTS 0xd512afa0, STC 0xd509ce17, type 0
[ 9713.892000] XVD pts error PTS 0xd512afa0, STC 0xd509d193, type 0
Since the have updated to the latest drivers I have a problem that some movies the screen freezes after a few second and the sound continues playing. When I skip forward the movie will start at the new position and will freeze again.
Before the update these recordings played without freezing.
I have a log when the screen will freeze:
have 1 video stream(s) (01d6), and 1 audio stream(s) (01d7), and the pcr pid is
01d6, and the text pid is ffffffff
PES filter: DMX_SET_PES_FILTER - Invalid argument
decoder state: play, vpid=470, apid=471
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
VIDEO_CONTINUE - ok
AUDIO_CONTINUE - ok
[ 248.008000] enable tsm0
doing version filtering
01d8: 02 12 73 05 00 00
mask: ff ff ff 3f 00 00
mode: 00 00 00 3e 00 00
[ 250.330000] printk: 150 messages suppressed.
[ 250.335000] XVD pts error PTS 0xa1686380, STC 0xa15f49b2, type 0
timeout 0012!
[ 255.328000] printk: 180 messages suppressed.
[ 255.333000] XVD pts error PTS 0xa16e0bf0, STC 0xa162b89a, type 0
[ 260.326000] printk: 137 messages suppressed.
[ 260.331000] XVD pts error PTS 0xa17188e8, STC 0xa166278a, type 0
action -> InfobarShowHideActions hide
[ 265.384000] printk: 139 messages suppressed.
[ 265.389000] XVD pts error PTS 0xa174e9c0, STC 0xa169a100, type 0
I have now on the box: Oozoon experimental 26-02-2011
Bevor jetzt jeder auf die Idee kommt, solche Bugreports in diesem Thread unterzubringen, muss ich wohl darauf hinweisen, dass nicht jedes geänderte Verhalten auf eine andere Bootloader-Version zurückzuführen ist. Wie Du selbst schreibst, hast Du ein Image geflasht und nicht nur einen anderen Bootloader. Du kannst gerne versuchen, den neueren Bootloader mit einem alten Image zu kombinieren, indem Du erst das Image und dann den Bootloader flashst:
http://dreamboxupdate.com/down…secondstage-dm8000-81.nfi
P.S.: Umgekehrt wird's nicht gehen. Ein aktuelles Image braucht immer einen aktuellen Secondstage.
Ich habe es gerade probiert mit ein pre-#81 image und dort die #81 secondstage in geschrieben und die Stopps treten nicht auf. Es tut mir Leid diesem posting verschmutzt zu haben.
Noch ein Problem mit die #81 und manche aufnahmen gemacht mit #81 spielen drei Sekunden und dann stoppt das Bild und den sound geht weiter. Druckt man auf 1/3/9 für weiter dann wieder 3 Sekunden Bild und so weiter.
Wenn ich ein Image mit #76 Flash dann geht alles wieder gut.
