I think it's in enigma config

Problem still there~ i should add that if there is extremly lots of movement (nascar car race) image might freeze for a second then oops it comes back and it is normal! unfortunately it goes back to a little freeze later on and comesback to jigling / framerate errors. The jigling happens on free channels too so it is not decription related.

Thanx mamba but it's not helping any with the issue . I sure hope developpers address this issue because its very annoying... I still don't understand why manufacturer ignores north american market so much...Pal boot up is a pain in the butt, initialisation is too... Other receiver manufacturers actually buy ntsc tvs and use feeds to test on. Its not that expensive it's half the price of one dmm 7025...

Atm it's like whatching vibrating pictures everytime something moves too fast on screen.

Just to say i'm pretty pissed that i buy something this expensive while a lower end linux dual tuner receiver has better ntsc support.

I understand taking time about it but complete ignorance is frustrating.

Hi,
i have not tried uhf however this problem doesn't present itself on the dm7020-s 7020-s is smoother... i understand of the refresh rate 60hz but it is not a refresh rate error but fps error...Mabe it is related to osd ?? And maybe it is skipping deleting frames? ntsc is supposed to run at 29.97 fps but it looks like its running at 25... it look slike a webcam lol not that bad but i think you know what i mean...if not pass your hand in front of computer monitor fast now imagine your hand is the image in tv...

Come on guys a lil support for such an expensive box? It's really awful, something must be done about that issue...

Using new Dm7025 .
I was wondering is there a way to change the fps settings or cpu filters?
My fps setting using ntsc 60 hz is very low almost hurts eyes when watching
for ex a car race, its terrible. Also when rolling banners you can not even read drivers name unless you blink. No problems with dm7020-s. Getting 98% signal.

At tmbinc are you talking about first thing after boot up pal ntsc selection menu on lcd display?

Oops wrong problem previous would come on second try on first try this is what i get....

./xml2po.py ../data/ >> enigma2.pot
/bin/sh: ./xml2po.py: /usr/bin/python: bad interpreter: No such file or directory
make[2]: *** [enigma2.pot] Error 126
make[2]: Leaving directory `/home/dmm/AA/dm7025/build/tmp/work/enigma2-1.0cvs20060117-r0/enigma2/po'
make[1]: *** [install-am] Error 2
make[1]: Leaving directory `/home/dmm/AA/dm7025/build/tmp/work/enigma2-1.0cvs20060117-r0/enigma2/po'
make: *** [install-recursive] Error 1
+ die 'oe_runmake failed'
+ oefatal 'oe_runmake failed'
+ echo FATAL: 'oe_runmake failed'
FATAL: oe_runmake failed
+ exit 1
ERROR: function do_install failed
ERROR: see log in /home/dmm/AA/dm7025/build/tmp/work/enigma2-1.0cvs20060117-r0/temp/log.do_install.652
NOTE: Task failed:
NOTE: package enigma2-1.0cvs20060117-r0: task do_package: failed
ERROR: TaskFailed event exception, aborting
NOTE: package enigma2-1.0cvs20060117: failed
ERROR: Build of dreambox-image failed
[dmm@localhost build]$

I am using mandrake (mandriva2006)

Hi,
i'm getting a problem with trying to compile my dm7025 image i done a clean world and deleted my init tools dir (then pull & update) and deleted source but still i get this error:

NOTE: package module-init-tools-cross-3.2.2-r0: task do_populate_staging: started
ERROR: function do_stage failed
ERROR: see log in /home/dmm/7025/build/tmp/work/module-init-tools-cross-3.2.2-r0/temp/log.do_stage.7417
NOTE: Task failed:
NOTE: package module-init-tools-cross-3.2.2-r0: task do_populate_staging: failed
ERROR: TaskFailed event exception, aborting
NOTE: package module-init-tools-cross-3.2.2: failed
ERROR: Build of dreambox-image failed

In log i only get :
NOTE: make install
make: *** No rule to make target `install'. Stop.
FATAL: oe_runmake failed

Also, what dirs must be in openembedded/packages/module-init-tools?
first time i tried to compile i had module-init-tools-3.2 and an empty module-init-tools-3.2.1
but now after new update only 3.2

Anybody had same problem? Maybe im not downloading the right source? I think its downloading 3.2 pre7 should it not be downloading the one for mipsel?

Could you pm this url your going to post it to Id like the schems too.
Also it would be a great sugestion to dream-m.m. to put a plastic shield between the supply and bottom of receiver in same principle as psu for computer. Would save lots since redoing a new type of casing would be very$$.

I think panasonic makes the power supplies and maybe be able to help you.But not by mentionning dreambox but by the power supply model number that's written on the board.