Dreambox DM520
M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@
BCM973625A0 CFE v15.3, Endian Mode: Little
Build Date: Tue Aug 2 14:43:27 2016 (Jann@Cynric)
Copyright (C) Broadcom Corporation.
CI box detected
card if inited
Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spae Area Size=16
MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256
CPU speed: 751MHz
DDR Frequency: 1061 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 16MB
RTS VERSION: rts_hevc10_1067
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1
init fp
Initializing USB.
CFE initialized.
found card in unknown state
ca valid!
***** DREAMBOX SSBL *****
Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 00ms to cancel
Proceeding with autoboot.. You can try aborting with Ctrl+C
Loader:elf Filesys:raw Dev:flash0.kernel File: Options[Blockierte Grafik: https://www.digital-eliteboard…default/xenforo/clear.png]null)
Loading: 0x80001000/25475264 0x8184c8c0/235952 Entry address is 0x805cd1d0
Closing network eth0
Ethernet link is up: 100 Mbps Full-Duplex
Starting program at 0x805cd1d0
▒[ 0.331000] console [ttyS0] enabled, bootconsole disabled
[ 0.331000] console [ttyS0] enabled, bootconsole disabled
[ 0.335000] loop: module loaded
[ 0.336000] brcmstb_nand: NAND controller driver is loaded
[ 0.337000] tun: Universal TUN/TAP device driver, 1.6
[ 0.337000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.460000] bcmgenet: configuring instance #0 for internal PHY
[ 0.480000] bcmgenet bcmgenet.0: (unregistered net_device): link down
[ 0.481000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.482000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.482000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus numbr 1
[ 0.514000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.520000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.521000] hub 1-0:1.0: USB hub found
[ 0.521000] hub 1-0:1.0: 2 ports detected
[ 0.522000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.523000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.523000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus numbr 2
[ 0.524000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
[ 0.590000] hub 2-0:1.0: USB hub found
[ 0.590000] hub 2-0:1.0: 2 ports detected
[ 0.591000] Initializing USB Mass Storage driver...
[ 0.592000] usbcore: registered new interface driver usb-storage
[ 0.593000] USB Mass Storage support registered.
[ 0.593000] i2c /dev entries driver
[ 0.594000] lirc_dev: IR Remote Control driver registered, major 253
[ 0.594000] usbcore: registered new interface driver btusb
[ 0.596000] TCP: cubic registered
[ 0.596000] NET: Registered protocol family 10
[ 0.598000] NET: Registered protocol family 17
[ 0.598000] Bluetooth: RFCOMM TTY layer initialized
[ 0.599000] Bluetooth: RFCOMM socket layer initialized
[ 0.600000] Bluetooth: RFCOMM ver 1.11
[ 0.600000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.601000] Bluetooth: BNEP filters: protocol multicast
[ 0.601000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.602000] L2TP core driver, V2.0
[ 0.602000] Registering the dns_resolver key type
[ 0.603000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.605000] EBI CS2: setting up NAND flash (primary)
[ 0.606000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 12MiB 3,3V 8-bit)
[ 0.607000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16 OOB, 8-bit, BCH-4
[ 0.607000]
[ 0.609000] Bad block table found at page 262080, version 0x01
[ 0.610000] Bad block table found at page 262016, version 0x01
[ 0.622000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.623000] 0x000000000000-0x00001f500000 : "rootfs"
[ 0.625000] 0x000000000000-0x000020000000 : "entire_device"
[ 0.627000] 0x00001f500000-0x00001fa00000 : "kernel"
[ 0.628000] EBI CS0: setting up SPI flash
[ 0.629000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
[ 0.630000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecate
[ 0.631000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
[ 0.631000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.638000] UBI: attaching mtd0 to ubi0
[ 0.639000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.640000] UBI: logical eraseblock size: 126976 bytes
[ 0.640000] UBI: smallest flash I/O unit: 2048
[ 0.641000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.642000] UBI: data offset: 4096
[ 3.785000] UBI: max. sequence number: 123898
[ 3.801000] UBI: attached mtd0 to ubi0
[ 3.801000] UBI: MTD device name: "rootfs"
[ 3.802000] UBI: MTD device size: 501 MiB
[ 3.802000] UBI: number of good PEBs: 4008
[ 3.803000] UBI: number of bad PEBs: 0
[ 3.803000] UBI: number of corrupted PEBs: 0
[ 3.804000] UBI: max. allowed volumes: 128
[ 3.805000] UBI: wear-leveling threshold: 4096
[ 3.805000] UBI: number of internal volumes: 1
[ 3.806000] UBI: number of user volumes: 1
[ 3.806000] UBI: available PEBs: 0
[ 3.807000] UBI: total number of reserved PEBs: 4008
[ 3.807000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 3.808000] UBI: max/mean erase counter: 223/31
[ 3.809000] UBI: image sequence number: -73013157
[ 3.809000] UBI: background thread "ubi_bgt0d" started, PID 54
[ 3.816000] ALSA device list:
[ 3.816000] No soundcards found.
INIT: version 2.88 booting
Starting udev
starting version 230
[ 4.476000] bcmdriver: module license 'Proprietary' taints kernel.
[ 4.477000] Disabling lock debugging due to kernel taint
[ 4.479000] BCMDRV: Initializing bcmdriver version $ 8
[ 4.479000] BCMDRV: Total intc words=3,Total Irqs=97
[ 4.481000] BCMDRV: Initialization complete
bootlogd: cannot allocate pseudo tty: No such file or directory
Mon Nov 13 15:09:59 UTC 2017
INIT: Entering runlevel: 5
Configuring network interfaces... [ 5.503000] ADDRCONF(NETDEV_UP): eth0: lin is not ready
udhcpc (v1.24.1) started
Sending discover...
[ 7.015000] bcmgenet bcmgenet.0: eth0: link up, 100 Mbps, full duplex
[ 7.015000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending discover...
Sending select for 192.168.178.40...
Lease of 192.168.178.40 obtained, lease time 864000
/etc/udhcpc.d/50default: Adding DNS 192.168.178.1
done.
Starting Dropbear SSH server: Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCjadsAou/pJDR7mJZ4zmB2P1GXufjdaYxrlizVcYGm7tgrkQxBKhwI1F/11MaLCwuQ+RkaTSi34pThdSt+iys3ZUiQorXYnKdANokhZpkL47opHcbVJ3W6qvNr/tW6fdgrpROODN5vaeKgFqZK10TmwPwbLkFyQcdJKcDVFsqdSOr6eVPPJDsEciCsNBx1yCfdsQFC3Hje/MAEmeIlX51+yADUjMC6dcMrRjwziEF+5snt8m6mhhAaW6wdlmmmtfrrxcN5V51pLo5LPNoTelF5I7bUwFzYE7XRwtE239cafSLUyoPFPSwdNUJ4p4p1bcSC0EPU/VvD46RXhrhL root@dm520
Fingerprint: md5 8a:82:f0:79:1c:37:45:1d:77:e9:45:8a:28:b2:9a:cb
dropbear.
Starting autoflashd.
Starting recovery-ui.
Starting tpmd.
Starting internet superserver: xinetd.
Starting Lighttpd Web Server: lighttpd.
2017-11-13 15:10:19: (../../lighttpd-1.4.39/src/log.c.194) server started
opendreambox 2.5.0 dm520 /dev/ttyS0
>>> Your Dreambox has booted into RESCUE MODE.
>>> Please log in as user 'root' (no password required),
>>> then run 'help' to get further information.
dm520 login: [ 77.460000] UBIFS: mounted UBI device 0, volume 0, name "dreambx-rootfs"
[ 77.461000] UBIFS: file system size: 501936128 bytes (490172 KiB, 478 MiB,3953 LEBs)
[ 77.462000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEs)
[ 77.463000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 77.464000] UBIFS: default compressor: lzo
[ 77.464000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 117.112000] UBIFS: un-mount UBI device 0, volume 0
Dreambox DM520
M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@
BCM973625A0 CFE v15.3, Endian Mode: Little
Build Date: Fri Aug 19 11:48:16 2016 (Jann@Cynric)
Copyright (C) Broadcom Corporation.
CI box detected
card if inited
Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spae Area Size=16
MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256
CPU speed: 751MHz
DDR Frequency: 1061 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 16MB
RTS VERSION: rts_hevc10_1067
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1
DM init finalization
yxml: processing file of 131072 bytes... succeeded!
no file loaded, create xml restoring default xml
loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1
[1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options
[2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options
[3] type 1, dev eth0, loader elf, filesys tftp, file , options bmem=192M@64M cosole=ttyS0,1000000 root=/dev/nfs ip=dhcp
added 3 sources to autoboot list
init fp
Initializing USB.
CFE initialized.
found card in unknown state
ca valid!
***** DREAMBOX SSBL *****
Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 00ms to cancel
Proceeding with autoboot.. You can try aborting with Ctrl+C
*** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf)
Ethernet link is up: 100 Mbps Full-Duplex
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:
Loading: 0x80001000/8534208 0x808248c0/258416 Entry address is 0x80685e50
Closing network eth0
Starting program at 0x80685e50
[ 0.260000] console [ttyS0] enabled, bootconsole disabled
[ 0.260000] console [ttyS0] enabled, bootconsole disabled
[ 0.265000] loop: module loaded
[ 0.266000] brcmstb_nand: NAND controller driver is loaded
[ 0.388000] bcmgenet: configuring instance #0 for internal PHY
[ 0.408000] bcmgenet bcmgenet.0: (unregistered net_device): link down
[ 0.409000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.410000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.410000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus numbr 1
[ 0.442000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.448000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.449000] hub 1-0:1.0: USB hub found
[ 0.449000] hub 1-0:1.0: 2 ports detected
[ 0.450000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.451000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.451000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus numbr 2
[ 0.452000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
[ 0.518000] hub 2-0:1.0: USB hub found
[ 0.519000] hub 2-0:1.0: 2 ports detected
[ 0.519000] Initializing USB Mass Storage driver...
[ 0.520000] usbcore: registered new interface driver usb-storage
[ 0.521000] USB Mass Storage support registered.
[ 0.521000] i2c /dev entries driver
[ 0.522000] lirc_dev: IR Remote Control driver registered, major 253
[ 0.522000] usbcore: registered new interface driver btusb
[ 0.524000] TCP: cubic registered
[ 0.524000] NET: Registered protocol family 10
[ 0.526000] NET: Registered protocol family 17
[ 0.526000] Bluetooth: RFCOMM TTY layer initialized
[ 0.527000] Bluetooth: RFCOMM socket layer initialized
[ 0.528000] Bluetooth: RFCOMM ver 1.11
[ 0.528000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.529000] Bluetooth: BNEP filters: protocol multicast
[ 0.529000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.530000] L2TP core driver, V2.0
[ 0.531000] Registering the dns_resolver key type
[ 0.531000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.533000] EBI CS2: setting up NAND flash (primary)
[ 0.534000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 12MiB 3,3V 8-bit)
[ 0.535000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16 OOB, 8-bit, BCH-4
[ 0.535000]
[ 0.537000] Bad block table found at page 262080, version 0x01
[ 0.538000] Bad block table found at page 262016, version 0x01
[ 0.540000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.541000] 0x000000000000-0x00001f500000 : "rootfs"
[ 0.543000] 0x000000000000-0x000020000000 : "entire_device"
[ 0.545000] 0x00001f500000-0x00001fa00000 : "kernel"
[ 0.546000] EBI CS0: setting up SPI flash
[ 0.547000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
[ 0.547000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecate
[ 0.548000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
[ 0.549000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.551000] UBI: attaching mtd0 to ubi0
[ 0.552000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.553000] UBI: logical eraseblock size: 126976 bytes
[ 0.553000] UBI: smallest flash I/O unit: 2048
[ 0.554000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.554000] UBI: data offset: 4096
[ 3.689000] UBI: max. sequence number: 124611
[ 3.705000] UBI: attached mtd0 to ubi0
[ 3.705000] UBI: MTD device name: "rootfs"
[ 3.706000] UBI: MTD device size: 501 MiB
[ 3.706000] UBI: number of good PEBs: 4008
[ 3.707000] UBI: number of bad PEBs: 0
[ 3.707000] UBI: number of corrupted PEBs: 0
[ 3.708000] UBI: max. allowed volumes: 128
[ 3.708000] UBI: wear-leveling threshold: 4096
[ 3.709000] UBI: number of internal volumes: 1
[ 3.709000] UBI: number of user volumes: 1
[ 3.710000] UBI: available PEBs: 0
[ 3.710000] UBI: total number of reserved PEBs: 4008
[ 3.711000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 3.712000] UBI: max/mean erase counter: 224/31
[ 3.712000] UBI: image sequence number: -73013157
[ 3.713000] UBI: background thread "ubi_bgt0d" started, PID 56
[ 3.715000] ALSA device list:
[ 3.715000] No soundcards found.
[ 3.813000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs"
[ 3.814000] UBIFS: file system size: 501936128 bytes (490172 KiB, 478 MiB,3953 LEBs)
[ 3.815000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEs)
[ 3.816000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 3.817000] UBIFS: default compressor: lzo
[ 3.817000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 3.819000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 3.823000] devtmpfs: mounted
/sbin/init: error while loading shared libraries: libkmod.so.2: cannot open shaed object file: No such file or directory
[ 3.919000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0007f00
[ 3.919000]
[ 3.920000] Rebooting in 180 seconds..