Beiträge von doublel

  • NUR Ausrufezeichen

    vielen Dank für die Antwort, ich sehe keine emmcflash devices aber flash0. Ist die nun hin?


    BOLT> show devices
    Device Name Description
    ------------------- ---------------------------------------------------------
    uart0 16550 DUART at 0xf040a900 channel 0
    mem0 Memory
    flash0.bolt SPI flash @ CS0: 0x00000000-0x00200000 (2048KB)
    flash0.nvram SPI flash @ CS0: 0x00200000-0x00220000 (128KB)
    flash0.devtree SPI flash @ CS0: 0x00220000-0x00240000 (128KB)
    flash0.recovery SPI flash @ CS0: 0x00240000-0x01000000 (14MB)
    flash0 SPI flash @ CS0: 0x00000000-0x02000000 (32MB)
    eth0 GENET Internal Ethernet at 0xf0b00000
    mdio0 GENET MDIO at 0xf0b00800
    sata0 SATA3 AHCI Device
    *** command status = 0


    das meint BOLT:
    BOLT> boot -tftp -elf 192.168.178.79:zImage-rescue-3.14.r0-dm900-20170901.bin
    Loader:elf Filesys:tftp Dev:eth0 File:192.168.178.79:zImage-rescue-3.14.r0-dm900-20170901.bin Options:(null)
    TFTP error 1: File not found
    Could not load zImage-rescue-3.14.r0-dm900-20170901.bin: File not found
    *** command status = -18


    das meint pumpkin:
    [10/10/17 21:57:24] 'zImage-rescue-3.14.r0-dm900-20170901.bin' of type 'octet' is requested from 192.168.178.20
    [10/10/17 21:57:24] >> 1: File not found


    und dann auch noch das:
    BOLT> boot -tftp -elf 192.168.178.79:zImage-rescue-3.14-r0-dm900-20170904.bin
    Loader:elf Filesys:tftp Dev:eth0 File:192.168.178.79:zImage-rescue-3.14-r0-dm900-20170904.bin Options:(null)
    Could not load zImage-rescue-3.14-r0-dm900-20170904.bin: Bad executable format
    *** command status = -11

  • NUR Ausrufezeichen

    Hat jemand eine Idee was das ist? Ich habe einfach neu gestartet und nun ist nur ein Ausrufezeichen im DIsplay, kein Zugang über telnet,
    keine IP wir zugewiesen, aber ein LOG konnte ich auslesen, verstehe da leider ... nichts


    CPU 01
    Dreambox DM900
    AVS init...
    AVS init OK
    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2 a002b00
    AVS load_code offset =00051000
    LOADED
    AVS: overtemp mon ON


    single board
    select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
    MEMSYS-STD
    SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
    MCB: FLEX
    AVS start:status=000000ff
    STB: Current voltage=000003ab(939)
    temperature=000088ea(35050)
    PV=00000364(868)
    MV=000003ad(941)
    AVS FW rev=30333278 [0.3.2.x]
    OK
    DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
    DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
    Sdram Scramble OTP = 0x00000001
    Sdram Scramble OK
    select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
    BFW load mode OTP = 0x0000000f
    bfw_hash_locked = 0x00000000
    BFW key3 OK, BFW load OK
    BFW v2.1.0
    COPY CODE... DONE
    MICH: disable success
    SSBL
    PINMUX
    CACHE FLUSH OK
    MMU ON
    CACHE FLUSH OK
    _fbss 07080cd0
    _ebss 0713dd70
    _end 0713dd90
    HEAP @ 07200000
    STACK @ 09300000
    ARCH: CONFIG OK
    CLR BSS 07080cd0 to 0713dd70 OK
    CLR SRAM OK
    CACHE FLUSH OK
    CPU CLKSET OK
    GO!


    ,/
    ,'/___, BOLT v1.18 v1.18 LOCAL BUILD
    .'__ ,' (2016-12-01 16:24:31 cynric@cynric-VirtualBox)
    /,' Copyright (C) 2016 Broadcom
    /'


    Board: BCM97252SSFF
    SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
    otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovi sion_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
    otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
    CPU: 2x B15 [420f00f3] 1719 MHz
    SCB: 432 MHz
    DDR0 @ 1067MHz, DDR1 @ 1067MHz
    RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
    CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
    EMMC1: transfer complete intr error, intr=0x608000
    Command 8 failed
    EMMC1: device failed to enter transfer mode
    CS1: NAND: unrecognized ID: 0xfefefefe 0xfefefefe
    RTS0: 0x1101004, 256 clients, ok
    RTS1: 0x1181004, 256 clients, ok
    BOX MODE: 5
    card if inited
    set pwm to 0/255
    disp id 5420
    load image
    AVS: park check
    AVS: temperature monitoring enabled
    AVS: STB: V=0.940V, T=+36.024C, PV=0.868V, MV=0.941V, FW=30333278 [0.3.2.x]
    USB otp=00000040
    USB @ 0xf0470200: IPP is active low, IOC is negative polarity
    init fp
    found card in unknown state
    ca valid!
    set pwm to 200/255
    Normal bootup
    Default boot device not found!
    Booting failed. Running recovery
    Loader:zimg Filesys:raw Dev:flash0.recovery File: Options:(null)


    Could not load : Bad executable format
    Booting recovery failed. This is probably a bad thing.
    *** DM bootloader, built on 2016-12-01 16:24:31
    Model DM900
    Revision 0
    Mac addr 00:09:34:42:6c:f7
    Serial no 110722-10161823
    Build date 2017-01-07
    Boot halted.
    Dropping you to the BOLT shell, be careful what you do there.
    BOLT>
    CAMERA:1
    :nauseated_face: