ops... nevermind!

Yes, I've done it immediately.

Now I'm back where I was before flashing the wrong image: installing softcams. And I have problems here too!...

I installed a few cccam extensions manually (ipk) but I never had any softcam menu. Where am I doing wrong?

Thx

I finally did it!!! THANK YOU VERY MUCH GUYS! I couldn't do that without you!

I'll never flash a wrong image in my life!

Well, I'm trying to do the same but I still have an error... it seems my dm820 can't find the bin file. Here's Putty log:

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.10.01 13:40:12 =~=~=~=~=~=~=~=~=~=~=~=


Dreambox DM8 20




M0


M1


SHMOO
0
00000000
1
00000000
C
do_boot
3s enter setup
2
1
0
enter setup . . .


SL2=1
LLMB=0000C000
BP=02000000
L2Cfg=1E76C637
L2Buf=44707700
BrCfg=F01C204F
BrMod=02800001
BrZp0=05000000
BrZp1=00002000
#@


BCM97434B0 CFE v3.15, Endian Mode: Little
Build Date: 20140202 (dm@dm)
Copyright (C) Broadcom Corporation.


MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256
found card in known state
ca valid!


CPU speed:            1407MHz
DDR Frequency:        667 MHz
DDR Mode:             DDR3
Total memory(MEMC 0): 1024MB
MEMC 0 DDR Width:     32
Total memory(MEMC 1): 1024MB
MEMC 1 DDR Width:     32




CFE initialized.




*** Autoboot: Trying device 'flash0.kernel' file kernel (flash0.kernel,raw)


Loader:elf Filesys:raw Dev:flash0.kernel File:kernel Options:
Loading: Failed.


*** Autoboot failed/stopped.


CFE> boot -tftp -elf 192.168.1.47:vmlinuz-rescue--3.4.r0.3-dm820-20160405.bin
enter ui_cmd_bootcommon
arg 192.168.1.47:vmlinuz-rescue--3.4.r0.3-dm820-20160405.bin
loader elf filesys tftp
1000 Mbps Full-Duplex
Device eth0:  hwaddr 00-09-34-2F-2E-EE, ipaddr 192.168.1.46, mask 255.255.255.0
        gateway 192.168.1.1, nameserver 80.58.61.250
Loader:elf Filesys:tftp Dev:(null) File:192.168.1.47:vmlinuz-rescue--3.4.r0.3-dm820-20160405.bin Options:(null)
call cfe_boot()
Loading: TFTP error 1: File not found
Failed.
Could not load vmlinuz-rescue--3.4.r0.3-dm820-20160405.bin: File not found
Trying again with '-nz' option
Loading: TFTP error 1: File not found
Failed.
Could not load vmlinuz-rescue--3.4.r0.3-dm820-20160405.bin: File not found
leave ui_cmd_bootcommon
*** command status = -18
CFE>

Hi m0rphU,
thank you very much for your fast and kind reply!
Well I finally got CFE prompt! Thanks! Now I go on with that procedure. Just one question: how could I "share" bin file on Pumpkin? Is it that "put file" button? Please could you explain me this?

Thank you

huascar

Dear all,
I have the same problem, I accidentally tried to load a DM520HD image (http://linuxsat-support.com/sh…-DM520-backup-by-master-G) in my DM820HD. The upgrade process stopped saying a "fatal error" and then I couldn't boot in rescue mode. I have the same red message on OLED display.
I carefully read all your comments, but I could fix my problem. I try to recap my situation.

I installed Putty and I can connect to my DM820HD typing its IP address (dhcp) using both TELNET or SSH modes. I can't connect if I boot with rescue mode (back button off, press front button, switch on back, 3, 2, 1 and... red message). I mean if I do that, I can't connect with Putty. The only way is to let the DM boot (OLED display only show DB logo).

I also connected mini USB cable (installing COM drivers) and I have it on COM12. But I can't do anything with that COM port: if I try to connect with Putty via COM (serial) I can't connect.

After a successful connection with Putty, I have a sort of "welcome message" (OpenATV 5.3... DM520). And my prompt is "root@dm520:-#"

I don't know how to create a bootlog for sharing: I set to save a "putty.log" file but I only have my prompt and a few other lines. I don't have a fully detailed booting infos.

I installed Pumpkin too but I don't know how to "share" the folder where I have dm820 rescue bin.

Last but not least, if I type the "boot..." command line I always get: "command unknown". Probably it's because I'm not typing at a "CFE prompt"... but what the hell is a CFE prompt?!?! and how I can get it?!

Well, sorry for all these questions, but as you understand I'm pretty a newbie. Thank you very much for your support!!!!!!