Beiträge von MikeV

  • slow disecq switching


    well the log is mailed..I see a cannot tune message in there and other things..But that can the experts decide better..


    Hope it will bring something up...

  • slow disecq switching

    i have connected the dish again on tuner B because no matter what it is the same..


    here is my current config (the full file)

  • slow disecq switching

    well in loopthrough to soacket A the same problem is there..


    You have seen my config..should be normal i think..
    nothing strange is installed or changed anywhere..


    just flashed the image, and configured the sats and after that the motor..


    when I remove the tuner B (nothing connected) the problem is also still there..so it looks to me like the pulses are not send correct or immediatly when switching to different sat..


    very strange...once on the sat, no problems during zapping..switch to other sat...have to wait again for a while, then after lock and picture all good again for that sat..
    when going back to astra (uncommited port 1 disecq AA) it goes fast.
    to all the other ports (up to uncommited 3 BB) it is like described above..


    weird weird weird and not funny :frowning_face:

  • slow disecq switching

    well did not make any changes here :frowning_face:


    still the same..it looks like he cannot decide what tuner to pick..
    signal is going up and down, quality is going up and down. BER is fixed value, and then after a while he locks or switches.


    But when doing a scan on a sat(tuner A) then there are 0 services found.
    Then i must scan with rotor (tuner B), and then he finds channels..


    Not nice :frowning_face:


    thx for the effort..


    Any more info I can give so someone can "debug" ?

  • slow disecq switching

    yep tried it all..I have it when switching to all other sats.
    When switching back to astra (uncommitted port 1 AA) then it is fast..back to other sat..he is "thinking" about what to do. :smiling_face:


    I tried fast diseq , and disecq repeat on/off it did not make a change..


    I shall post my config here..


    I run the own build with enigma from 27-06.


    I have Tuner A uncommitted Spaun,and disecq are spaun.
    Tuner B is motor. They can receive both these sat's maybe the box is thinking wich tuner to pick ??


    here my config part for tuner and LNB..
    PS: On my dm7000 all is fine with same uncommitted dish..


  • slow disecq switching

    hello,


    I have T90 dish with 12 LNB's in that setup.
    Uncommited switch and disecq switches.


    When watching channel on astra (tuner A) and switch to channel on 5 east (also Tuner A) nothing happens for about 10 to 15 second.
    You can see the signal bar move but not a lock or picture..Leave it on the channel and eventually it will lock and have picture..
    When zapping back to astra then I have picture at once..Go back again to 5 east, same problem..Once on 5 east no problems at all.
    I have tried multiple satellite.xlm files but that does not fix it.
    Also did a new transponder scan..same results..


    It seems like sometimes he does not get the change of sat correctly..But that is my "poor man judgment :smiling_face: ).


    Is this a know bug/issue ? My setup is ok..

  • Enigma2 Skin Selector Plugin

    i get this error.


    root@dm7025:/var/tmp# ipkg install enigma2-skinselector_1.0-20060601-r0_mipsel.i
    pk
    Installing enigma2-skinselector (1.0-20060601-r0) to root...
    Configuring enigma2-skinselector
    Configuring gst-plugins-good
    //usr/lib/ipkg/info/gst-plugins-good.postinst: 14: gconftool-2: not found
    //usr/lib/ipkg/info/gst-plugins-good.postinst: 14: gconftool-2: not found
    postinst script returned status 127
    ERROR: gst-plugins-good.postinst returned 127
    root@dm7025:/var/tmp#

  • sound "hickups" on optical output

    Zitat

    Originally posted by squaker
    For information:


    in an other board is to read, that the dropout-bug on opt.-out is well known by DMM and would be fixed in the next official firmware-release.


    Well it would be nice if some sort of feedback is then somewhere to read.Or at least a response on the topic(s) that are being posted in the bug(s) sections.


    I cannot browse all the sections and parts of all boards :smiling_face: constantly to see what is happening behind the scenes.


    The sound "changeover" on premiere i had for 2 days when I went to portal and selected an event. Then the sound would now and then change back to tone 1 when tone2 was selected.
    This was with an "not supported" cam and I must say since those 2 days it has not come back (yet again).


    So maybe premiere was doing things ?

  • sound "hickups" on optical output

    question :


    Is there anywhere a list of bugs to fix for the 7025 ?


    I am now back to my dm7000 because of some bugs that are reported here.
    Are they on the TODO list or is this just a place to tell them and never hear anything ?


    Maybe a "list to do because of known and verified bugs" is a nice idea for people to see what is happening.


    I can report , and then nothing..


    Hope this is a usefull idea and sure would make many people happy i guess.


    thanks,

  • sound "hickups" on optical output

    It has nothing to do with my signal or receiver..


    I am sure of that.
    The other boxes (7000 and 7020) don't have this issues. (when connected on the same optical cable and same channel )
    It is also not my network , CI or card.


    It is really a dm7025 issue (driver or maybe hardware) and I am not the only person with this issue.


    It is even so strange that when watching premiere in english the box sometimes just changes back to german language..So it looks like the box is "not locking" on a pid or something (i don't know what).


    And I don't use sound from the scart I only use optical output for ALL the sound of every channel.

  • error compiling 7025

    well did it again, clean try.
    same error ..here is my lines from the config log


  • error compiling 7025

    this is in the log


    NOTE: make DESTDIR=/home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/temp-staging install
    make[1]: Entering directory `/home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/gst-plugins-good-0.10.2'
    make[1]: *** No rule to make target `install'. Stop.
    make[1]: Leaving directory `/home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/gst-plugins-good-0.10.2'
    FATAL: oe_runmake failed


    and this is in the log_do_compile log


    mv -f ".libs/libgstcacasink.expT" ".libs/libgstcacasink.exp"
    echo "{ global:" > .libs/libgstcacasink.ver
    cat .libs/libgstcacasink.exp | sed -e "s/\(.*\)/\1;/" >> .libs/libgstcacasink.ver
    echo "local: *; };" >> .libs/libgstcacasink.ver
    ccache mipsel-linux-gcc -shared .libs/libgstcacasink_la-gstcacasink.o -Wl,--rpath -Wl,/home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib -Wl,--rpath -Wl,/home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib -L/home/dm/tuxbox-dev/dm7025/build/tmp/work/glib-2.0-2.8.2-r2/glib-2.8.2/glib/.libs -L/home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/.libs -L/home/dm/tuxbox-dev/dm7025/build/tmp/work/gstreamer-0.10.4-r0/gstreamer-0.10.4/gst/.libs -L/home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib -pthread /home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/libgstbase-0.10.so /home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/libgstreamer-0.10.so /home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/libgobject-2.0.so /home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/libgmodule-2.0.so -ldl /home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/libgthread-2.0.so /home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/libxml2.so -lz -lm /home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib/libglib-2.0.so -L/usr/lib -lcaca_pic -lslang -lX11 -L/usr/X11R6/lib -lncurses -Wl,-rpath-link -Wl,/home/dm/tuxbox-dev/dm7025/build/tmp/staging/mipsel-linux/lib -Wl,-O1 -Wl,-soname -Wl,libgstcacasink.so -Wl,-version-script -Wl,.libs/libgstcacasink.ver -o .libs/libgstcacasink.so
    /home/dm/tuxbox-dev/dm7025/build/tmp/cross/lib/gcc/mipsel-linux/4.1.0/../../../../mipsel-linux/bin/ld: skipping incompatible /usr/lib/libcaca_pic.a when searching for -lcaca_pic
    /home/dm/tuxbox-dev/dm7025/build/tmp/cross/lib/gcc/mipsel-linux/4.1.0/../../../../mipsel-linux/bin/ld: cannot find -lcaca_pic
    collect2: ld returned 1 exit status
    make[4]: *** [libgstcacasink.la] Error 1
    make[4]: Leaving directory `/home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/gst-plugins-good-0.10.2/ext/libcaca'
    make[3]: *** [all-recursive] Error 1
    make[3]: Leaving directory `/home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/gst-plugins-good-0.10.2/ext'
    make[2]: *** [all-recursive] Error 1
    make[2]: Leaving directory `/home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/gst-plugins-good-0.10.2'
    make[1]: *** [all] Error 2
    make[1]: Leaving directory `/home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/gst-plugins-good-0.10.2'
    FATAL: oe_runmake failed

  • error compiling 7025

    I have been trying many time to compile image for dm7025.


    the build keeps failing on this:
    NOTE: package gst-plugins-good-0.10.2: started
    NOTE: package gst-plugins-good-0.10.2-r0: task do_fetch: started
    NOTE: package gst-plugins-good-0.10.2-r0: task do_fetch: completed
    NOTE: package gst-plugins-good-0.10.2-r0: task do_compile: started
    NOTE: package gst-plugins-good-0.10.2-r0: task do_compile: completed
    NOTE: package gst-plugins-good-0.10.2-r0: task do_populate_staging: started
    ERROR: function do_stage failed
    ERROR: see log in /home/dm/tuxbox-dev/dm7025/build/tmp/work/gst-plugins-good-0.10.2-r0/temp/log.do_stage.9940
    NOTE: Task failed:
    NOTE: package gst-plugins-good-0.10.2-r0: task do_populate_staging: failed
    ERROR: TaskFailed event exception, aborting
    NOTE: package gst-plugins-good-0.10.2: failed
    ERROR: Build of dreambox-image failed
    make: *** [image] Error 1


    I changed cvsdate and versions form 1.2 to 1.3 and 1.4 but no change.
    Deleted everything and started from scratch, same result.
    Any help is welcome.

  • sound "hickups" on optical output

    Hi,


    I have my dm7025 connected with an optical cable to my receiver.
    Every x minutes the sound stops for a fraction of a second (totally) and then comes back again like before.
    I have this on ALL the channels.
    The settings are normal, and it is NOT the receiver or settings on that.
    I have all the boxes (I need more space) dm500, dm7000, dm7020 and now the dm7025.
    Only the 7025 has this issue (however the 500 is not connected)
    It is not only on encrypted channels it is also on FTA channels (BVN).


    Is this a know thing and can that (hopefully) be fixed ?


    thx

  • multisystem (TV) support

    FOr now you must choose PAL or NTSC.
    Please add multisystem support as soon as possible please.
    Now ntsc plays with stottering on PAL mode.
    multisystem is (just like the dm7000) a needy thing on the boxes and LCD / Plasma screens.


    Please consider !