Tach zusammen
Hab da noch ne Frage im bezug auf USB Sticks in der 7020.
Warum bekomme ich einen Fehler im Log wenn ich den das erste mal USB Stick im Betrieb der Dreambox abstecke?
Habe ich hier nur einen Fehler gemacht oder ist das einfach so oder ist da ein Fehler drin?
Hier mal ein Log:
usb 1-1: USB disconnect, address 2
target0:0:0: Illegal state transition <NULL>->cancel
Badness in scsi_device_set_state at drivers/scsi/scsi_lib.c:1714
Call trace:
[c000495c] check_bug_trap+0x98/0xdc
[c00049c4] ProgramCheckException+0x24/0x1f0
[c00041d8] ret_from_except_full+0x0/0x4c
[c01b2468] scsi_device_set_state+0xc0/0x14c
[c01ad250] scsi_device_cancel+0x34/0x160
[c01ad3b8] scsi_device_cancel_cb+0x18/0x28
[c0183a00] device_for_each_child+0x68/0xec
[c01ad410] scsi_host_cancel+0x48/0xc4
[c01ad4b0] scsi_remove_host+0x24/0x9c
[c01e17fc] storage_disconnect+0x48/0x60
[c01cecd0] usb_unbind_interface+0x88/0xc8
[c0184fd0] device_release_driver+0x84/0x88
[c01851b0] bus_remove_device+0x80/0x130
[c0183904] device_del+0xb0/0x114
[c0183980] device_unregister+0x18/0x30
usb 1-1: new full speed USB device using address 3
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: USB Model: Flash Disk Rev: 1100
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 494592 512-byte hdwr sectors (253 MB)
sdb: Write Protect is on
sdb: asking for cache data failed
sdb: assuming drive cache: write through
/dev/scsi/host1/bus0/target0/lun0: unknown partition table
Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
usb 1-1: USB disconnect, address 3
usb 1-1: new full speed USB device using address 4
scsi2 : SCSI emulation for USB Mass Storage devices
Vendor: USB Model: Flash Disk Rev: 1100
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 494592 512-byte hdwr sectors (253 MB)
sdb: Write Protect is on
sdb: asking for cache data failed
sdb: assuming drive cache: write through
/dev/scsi/host2/bus0/target0/lun0: unknown partition table
Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0
usb 1-1: USB disconnect, address 4
usb 1-1: new full speed USB device using address 5
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: VBTM Model: Store 'n' Go Rev: 1.04
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 1001472 512-byte hdwr sectors (513 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write through
/dev/scsi/host3/bus0/target0/lun0: unknown partition table
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi3, channel 0, id 0, lun 0, type 0
usb 1-1: USB disconnect, address 5
[EPGC] start cleanloop
[EPGC] stop cleanloop
[EPGC] 3474602 bytes for cache used
usb 1-1: new full speed USB device using address 6
scsi4 : SCSI emulation for USB Mass Storage devices
Vendor: USB Model: Flash Disk Rev: 1100
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 494592 512-byte hdwr sectors (253 MB)
sdb: Write Protect is on
sdb: asking for cache data failed
sdb: assuming drive cache: write through
/dev/scsi/host4/bus0/target0/lun0: unknown partition table
Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi4, channel 0, id 0, lun 0, type 0
usb 1-1: USB disconnect, address 6
usb 1-1: new full speed USB device using address 7
scsi5 : SCSI emulation for USB Mass Storage devices
Vendor: USB Model: Flash Disk Rev: 1100
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 494592 512-byte hdwr sectors (253 MB)
sdb: Write Protect is on
sdb: asking for cache data failed
sdb: assuming drive cache: write through
/dev/scsi/host5/bus0/target0/lun0: unknown partition table
Attached scsi removable disk sdb at scsi5, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi5, channel 0, id 0, lun 0, type 0
Ok, habe geschummelt und zwei verschiedene Sticks verwendet.
Bye
SatTel