=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.10.22 12:59:14 =~=~=~=~=~=~=~=~=~=~=~= BCM97400 AB FFFFFFFF 1s Sync=0 LLMB=0 L2=0 RAC_I=0 RAC_D=0 Copy Code...34TUCV (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox DM8000 FIRST STAGE 1.00 {BO23456}  2ND STAGE OK, build #84 (2011-09-01) 0.000 - BCM board setup Configure MEMC1_2........ Done 0.039 - fp init FP version 7 detected 0.106 - ca init 0.820 - load config 1.400 - config loaded. * press [S] to enter setup OLED found! lcd: BOOT #84 - NAND PROBE: 2c da 80 95 (normal) - read config file: /boot/secondstage.conf detected jffs2 blocksize: 128kb +++++++++++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUU dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / - \ |  done. find_inode failed for name=secondstage.conf load: Failed to find inode - failed to open /boot/secondstage.conf - failed to open /cf/autorun.bat lcd: /boot/bootlogo-dm8000.elf.gz bootlogo size: 170039 Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K !PAL_I !PAL_M !PAL_N !PAL_NC !PAL_60 !SECAM_L !SECAM_B !SECAM_G !SECAM_D !SECAM_K !SECAM_H 1080i !1080p 720p 480p 1080i_50Hz 1080p_24Hz 1080p_25Hz 1080p_30Hz !1080p_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p DVI_800x600p DVI_1024x768p !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_ReducedBlank !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_640x480p_85Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz !DVI_1920x1080p_60Hz_Red !Custom0 !Custom1 !Custom2 best supported mode is 25 using 1920x1080i (50.00 Hz) HDMI using colorspace: 1 create surface 1920 1080 Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard parsing JPEG header.. Virtual FB Size: 1280x720 lcd: /boot/vmlinux-3.2-dm8000.gz [ 0.000000] Linux version 3.2-dm8000 (oe@porky.dream-property.net) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Thu Oct 11 13:26:30 UTC 2012 [ 0.000000] Fetching vars from bootloader... [ 0.000000] Early serial console at MMIO32 0x10400b00 (options '115200n8') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1 [ 0.000000] Using 256 MB RAM (from straps) [ 0.000000] Fetch var 'memsize' = '154' [ 0.000000] CPU revision is: 0002a042 (Brcm4380) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] bmem: adding 102 MB RESERVED region at 154 MB (0x06600000@0x09a00000) [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00010000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5440 r8192 d15040 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw bmem=102M@154M [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.000000] Memory: 149372k/262144k available (4674k kernel code, 112772k reserved, 978k data, 220k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] Detected MIPS clock frequency: 405 MHz (202.508 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.001000] Calibrating delay loop... 403.45 BogoMIPS (lpj=201728) [ 0.013000] pid_max: default: 32768 minimum: 301 [ 0.014000] Mount-cache hash table entries: 512 [ 0.017000] SMP: Booting CPU1... [ 0.018000] CPU revision is: 0002a042 (Brcm4380) [ 0.018000] FPU revision is: 00130001 [ 0.018000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.018000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.029000] SMP: CPU1 is running [ 0.029000] Brought up 2 CPUs [ 0.030000] devtmpfs: initialized [ 0.034000] NET: Registered protocol family 16 [ 0.036000] PCI2.3->SDRAM window: 256 MB [ 0.043000] bio: create slab at 0 [ 0.045000] SCSI subsystem initialized [ 0.046000] usbcore: registered new interface driver usbfs [ 0.047000] usbcore: registered new interface driver hub [ 0.048000] usbcore: registered new device driver usb [ 0.049000] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.050000] PCI: found device 168c:001a on PCI2.3 bus, slot 1 (irq 33) [ 0.051000] pci 0000:00:01.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff] [ 0.052000] pci 0000:00:01.0: BAR 0: set to [mem 0xd0000000-0xd000ffff] (PCI address [0xd0000000-0xd000ffff]) [ 0.053000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42) [ 0.054000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff] [ 0.055000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff]) [ 0.056000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref] [ 0.057000] Switching to clocksource upg [ 0.071000] NET: Registered protocol family 2 [ 0.076000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.084000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.092000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.099000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.106000] TCP reno registered [ 0.109000] UDP hash table entries: 128 (order: 0, 4096 bytes) [ 0.115000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) [ 0.122000] NET: Registered protocol family 1 [ 0.127000] RPC: Registered named UNIX socket transport module. [ 0.134000] RPC: Registered udp transport module. [ 0.139000] RPC: Registered tcp transport module. [ 0.144000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.153000] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.162000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.171000] msgmni has been set to 291 [ 0.177000] io scheduler noop registered [ 0.181000] io scheduler cfq registered (default) [ 0.186000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.215000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 69) is a 16550A [ 0.222000] console [ttyS0] enabled, bootconsole disabled [ 0.222000] console [ttyS0] enabled, bootconsole disabled [ 0.235000] loop: module loaded [ 0.239000] brcm-pm: enabling sata clocks [ 0.243000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003) [ 0.445000] scsi0 : sata_brcmstb [ 0.449000] scsi1 : sata_brcmstb [ 0.453000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42 [ 0.460000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42 [ 0.689000] 4524 kb/s [ 0.691000] - NAND PROBE: 2c da 80 95 [ 0.695000] ONFI flash detected [ 0.699000] ONFI param page 0 valid [ 0.702000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD) [ 0.710000] Scanning device for bad blocks [ 1.339000] Creating 4 MTD partitions on "MT29F2G08AAD": [ 1.345000] 0x000000000000-0x000010000000 : "complete" [ 1.352000] 0x000000000000-0x000000100000 : "loader" [ 1.358000] 0x000000100000-0x000000800000 : "boot partition" [ 1.365000] 0x000000800000-0x000010000000 : "root partition" [ 1.372000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0 [ 1.381000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:1c:2f:c2) [ 1.389000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.396000] brcm-pm: enabling usb clocks [ 1.400000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 1.405000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 1.444000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300 [ 1.455000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 1.461000] hub 1-0:1.0: USB hub found [ 1.465000] hub 1-0:1.0: 2 ports detected [ 1.469000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI [ 1.474000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 [ 1.513000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500 [ 1.524000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 [ 1.530000] hub 2-0:1.0: USB hub found [ 1.534000] hub 2-0:1.0: 2 ports detected [ 1.538000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.545000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 1.550000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3 [ 1.557000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400 [ 1.628000] hub 3-0:1.0: USB hub found [ 1.632000] hub 3-0:1.0: 2 ports detected [ 1.637000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI [ 1.642000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4 [ 1.644000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600 [ 1.665000] ata1: SATA link down (SStatus 4 SControl 300) [ 1.721000] hub 4-0:1.0: USB hub found [ 1.725000] hub 4-0:1.0: 2 ports detected [ 1.729000] Initializing USB Mass Storage driver... [ 1.734000] usbcore: registered new interface driver usb-storage [ 1.740000] USB Mass Storage support registered. [ 1.745000] i2c /dev entries driver [ 1.749000] ALSA device list: [ 1.752000] No soundcards found. [ 1.755000] TCP cubic registered [ 1.759000] NET: Registered protocol family 17 [ 1.763000] Registering the dns_resolver key type [ 1.776000] usb 1-1: new high-speed USB device number 2 using ehci-brcm [ 1.898000] hub 1-1:1.0: USB hub found [ 1.902000] hub 1-1:1.0: 3 ports detected [ 2.009000] usb 1-2: new high-speed USB device number 3 using ehci-brcm [ 2.133000] scsi2 : usb-storage 1-2:1.0 [ 2.200000] usb 1-1.3: new high-speed USB device number 4 using ehci-brcm [ 2.284000] scsi3 : usb-storage 1-1.3:1.0 [ 3.141000] scsi 2:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 [ 3.150000] scsi 2:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0 [ 3.159000] scsi 2:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0 [ 3.168000] scsi 2:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0 [ 3.291000] scsi 3:0:0:0: Direct-Access Ut165 USB2FlashStorage 0.00 PQ: 0 ANSI: 2 [ 3.304000] sd 3:0:0:0: [sde] 15794176 512-byte logical blocks: (8.08 GB/7.53 GiB) [ 3.312000] sd 3:0:0:0: [sde] Write Protect is off [ 3.318000] sd 3:0:0:0: [sde] Asking for cache data failed [ 3.323000] sd 3:0:0:0: [sde] Assuming drive cache: write through [ 3.333000] sd 3:0:0:0: [sde] Asking for cache data failed [ 3.339000] sd 3:0:0:0: [sde] Assuming drive cache: write through [ 3.630000] sde: sde1 [ 3.940000] sd 3:0:0:0: [sde] Asking for cache data failed [ 3.946000] sd 3:0:0:0: [sde] Assuming drive cache: write through [ 3.952000] sd 3:0:0:0: [sde] Attached SCSI removable disk [ 5.494000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 7.832000] ata2.00: ATA-8: WDC WD20EADS-32S2B0, 01.00A01, max UDMA/133 [ 7.839000] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 7.850000] ata2.00: configured for UDMA/133 [ 7.855000] scsi 1:0:0:0: Direct-Access ATA WDC WD20EADS-32S 01.0 PQ: 0 ANSI: 5 [ 7.864000] sd 1:0:0:0: [sdf] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 7.872000] sd 1:0:0:0: [sdf] Write Protect is off [ 7.877000] sd 1:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.895000] sdf: sdf1 [ 7.899000] sd 1:0:0:0: [sdf] Attached SCSI disk [ 33.830000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 44.054000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 60.278000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 60.503000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 70.727000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 70.849000] sd 2:0:0:0: Device offlined - not ready after error recovery [ 70.856000] sd 2:0:0:0: rejecting I/O to offline device [ 70.861000] sd 2:0:0:0: rejecting I/O to offline device [ 70.867000] sd 2:0:0:0: rejecting I/O to offline device [ 70.872000] sd 2:0:0:0: [sda] READ CAPACITY failed [ 70.877000] sd 2:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00 [ 70.883000] sd 2:0:0:0: [sda] Sense not available. [ 70.888000] sd 2:0:0:0: rejecting I/O to offline device [ 70.893000] sd 2:0:0:0: [sda] Write Protect is off [ 70.898000] sd 2:0:0:0: rejecting I/O to offline device [ 70.903000] sd 2:0:0:0: [sda] Asking for cache data failed [ 70.909000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 70.916000] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 71.493000] sd 2:0:0:3: [sdd] Attached SCSI removable disk [ 71.494000] sd 2:0:0:1: [sdb] 8027712 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 71.496000] sd 2:0:0:1: [sdb] Write Protect is off [ 71.498000] sd 2:0:0:1: [sdb] No Caching mode page present [ 71.498000] sd 2:0:0:1: [sdb] Assuming drive cache: write through [ 71.523000] sd 2:0:0:2: [sdc] Attached SCSI removable disk [ 71.533000] sd 2:0:0:1: [sdb] No Caching mode page present [ 71.538000] sd 2:0:0:1: [sdb] Assuming drive cache: write through [ 71.546000] sdb: sdb1 [ 71.552000] sd 2:0:0:1: [sdb] No Caching mode page present [ 71.558000] sd 2:0:0:1: [sdb] Assuming drive cache: write through [ 71.564000] sd 2:0:0:1: [sdb] Attached SCSI removable disk [ 75.152000] VFS: Mounted root (jffs2 filesystem) on device 31:3. [ 75.193000] devtmpfs: mounted [ 75.197000] Freeing unused kernel memory: 220k freed INIT: version 2.88 booting Displaying bootlogo. Starting udev [ 78.436000] udevd[88]: starting version 182 [ 79.257000] stb_core: module license 'Proprietary' taints kernel. [ 79.264000] Disabling lock debugging due to kernel taint [ 80.012000] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, XR) [ 80.246000] wlan: svn r3314 [ 80.437000] ath_pci: svn r3314 [ 80.441000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 80.447000] Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies [ 80.699000] uncorrectable error : [ 80.703000] uncorrectable error : [ 80.706000] uncorrectable error : [ 80.710000] uncorrectable error : [ 80.713000] mtd->read(0x600 bytes from 0x648200) returned ECC error [ 80.720000] JFFS2 notice: (122) read_dnode: node CRC failed on dnode at 0x648200: read 0x7801668c, calculated 0x1668cc6 [ 80.825000] Node CRC 78906d20 != calculated CRC be6debc6 for node at 0063e638 [ 80.844000] uncorrectable error : [ 80.847000] uncorrectable error : [ 80.851000] mtd->read(0x32d bytes from 0x640e34) returned ECC error [ 80.857000] Data CRC f872ddfe != calculated CRC a1efc381 for node at 00640df0 [ 80.913000] uncorrectable error : [ 80.917000] mtd->read(0x44 bytes from 0x64802c) returned ECC error [ 80.954000] fpga init [ 81.159000] ath_rate_sample: 1.2 (svn r3314) [ 81.176000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps [ 81.182000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps [ 81.194000] wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps [ 81.203000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP [ 81.615000] ath_pci: wifi0: Atheros 2413: mem=0xd0000000, irq=33 [ 83.514000] no done ack [ 83.517000] no init ack [ 83.520000] no init ack [ 83.523000] no init ack [ 83.526000] no init ack [ 83.528000] Kernel panic - not syncing: cannot configure fpga! [ 83.528000] [ 83.535000] Rebooting in 180 seconds.. BCM97400 AB FFFFFFFF 1s Sync=0 LLMB=0 L2=0 RAC_I=0 RAC_D=0 Copy Code...34TUCV (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox DM8000 FIRST STAGE 1.00 {BO23456}  2ND STAGE OK, build #84 (2011-09-01) 0.000 - BCM board setup Configure MEMC1_2........ Done 0.039 - fp init FP version 7 detected 0.106 - ca init 0.821 - load config 1.401 - config loaded. * press [S] to enter setup OLED found! lcd: BOOT #84 - NAND PROBE: 2c da 80 95 (normal) - read config file: /boot/secondstage.conf detected jffs2 blocksize: 128kb +++++++++++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUU dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / - \ |  done. find_inode failed for name=secondstage.conf load: Failed to find inode - failed to open /boot/secondstage.conf - failed to open /cf/autorun.bat lcd: /boot/bootlogo-dm8000.elf.gz bootlogo size: 170039 Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K !PAL_I !PAL_M !PAL_N !PAL_NC !PAL_60 !SECAM_L !SECAM_B !SECAM_G !SECAM_D !SECAM_K !SECAM_H 1080i !1080p 720p 480p 1080i_50Hz 1080p_24Hz 1080p_25Hz 1080p_30Hz !1080p_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p DVI_800x600p DVI_1024x768p !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_ReducedBlank !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_640x480p_85Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz !DVI_1920x1080p_60Hz_Red !Custom0 !Custom1 !Custom2 best supported mode is 25 using 1920x1080i (50.00 Hz) HDMI using colorspace: 1 create surface 1920 1080 Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard parsing JPEG header.. Virtual FB Size: 1280x720 lcd: /boot/vmlinux-3.2-dm8000.gz [ 0.000000] Linux version 3.2-dm8000 (oe@porky.dream-property.net) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Thu Oct 11 13:26:30 UTC 2012 [ 0.000000] Fetching vars from bootloader... [ 0.000000] Early serial console at MMIO32 0x10400b00 (options '115200n8') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1 [ 0.000000] Using 256 MB RAM (from straps) [ 0.000000] Fetch var 'memsize' = '154' [ 0.000000] CPU revision is: 0002a042 (Brcm4380) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] bmem: adding 102 MB RESERVED region at 154 MB (0x06600000@0x09a00000) [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00010000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5440 r8192 d15040 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw bmem=102M@154M [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.000000] Memory: 149372k/262144k available (4674k kernel code, 112772k reserved, 978k data, 220k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] Detected MIPS clock frequency: 405 MHz (202.508 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.001000] Calibrating delay loop... 403.45 BogoMIPS (lpj=201728) [ 0.013000] pid_max: default: 32768 minimum: 301 [ 0.014000] Mount-cache hash table entries: 512 [ 0.017000] SMP: Booting CPU1... [ 0.018000] CPU revision is: 0002a042 (Brcm4380) [ 0.018000] FPU revision is: 00130001 [ 0.018000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.018000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.029000] SMP: CPU1 is running [ 0.029000] Brought up 2 CPUs [ 0.030000] devtmpfs: initialized [ 0.034000] NET: Registered protocol family 16 [ 0.036000] PCI2.3->SDRAM window: 256 MB [ 0.043000] bio: create slab at 0 [ 0.045000] SCSI subsystem initialized [ 0.046000] usbcore: registered new interface driver usbfs [ 0.047000] usbcore: registered new interface driver hub [ 0.048000] usbcore: registered new device driver usb [ 0.049000] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.050000] PCI: found device 168c:001a on PCI2.3 bus, slot 1 (irq 33) [ 0.051000] pci 0000:00:01.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff] [ 0.052000] pci 0000:00:01.0: BAR 0: set to [mem 0xd0000000-0xd000ffff] (PCI address [0xd0000000-0xd000ffff]) [ 0.053000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42) [ 0.054000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff] [ 0.055000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff]) [ 0.056000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref] [ 0.057000] Switching to clocksource upg [ 0.071000] NET: Registered protocol family 2 [ 0.076000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.084000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.091000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.098000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.105000] TCP reno registered [ 0.108000] UDP hash table entries: 128 (order: 0, 4096 bytes) [ 0.114000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) [ 0.121000] NET: Registered protocol family 1 [ 0.126000] RPC: Registered named UNIX socket transport module. [ 0.132000] RPC: Registered udp transport module. [ 0.137000] RPC: Registered tcp transport module. [ 0.142000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.152000] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.160000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.170000] msgmni has been set to 291 [ 0.175000] io scheduler noop registered [ 0.179000] io scheduler cfq registered (default) [ 0.184000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.212000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 69) is a 16550A [ 0.219000] console [ttyS0] enabled, bootconsole disabled [ 0.219000] console [ttyS0] enabled, bootconsole disabled [ 0.233000] loop: module loaded [ 0.236000] brcm-pm: enabling sata clocks [ 0.240000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003) [ 0.443000] scsi0 : sata_brcmstb [ 0.447000] scsi1 : sata_brcmstb [ 0.451000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42 [ 0.458000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42 [ 0.687000] 4524 kb/s [ 0.689000] - NAND PROBE: 2c da 80 95 [ 0.693000] ONFI flash detected [ 0.696000] ONFI param page 0 valid [ 0.700000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD) [ 0.707000] Scanning device for bad blocks [ 1.337000] Creating 4 MTD partitions on "MT29F2G08AAD": [ 1.342000] 0x000000000000-0x000010000000 : "complete" [ 1.349000] 0x000000000000-0x000000100000 : "loader" [ 1.356000] 0x000000100000-0x000000800000 : "boot partition" [ 1.363000] 0x000000800000-0x000010000000 : "root partition" [ 1.370000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0 [ 1.379000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:1c:2f:c2) [ 1.387000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.393000] brcm-pm: enabling usb clocks [ 1.397000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 1.403000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 1.441000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300 [ 1.452000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 1.458000] hub 1-0:1.0: USB hub found [ 1.462000] hub 1-0:1.0: 2 ports detected [ 1.466000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI [ 1.472000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 [ 1.510000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500 [ 1.521000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 [ 1.527000] hub 2-0:1.0: USB hub found [ 1.531000] hub 2-0:1.0: 2 ports detected [ 1.535000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.542000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 1.547000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3 [ 1.554000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400 [ 1.625000] hub 3-0:1.0: USB hub found [ 1.629000] hub 3-0:1.0: 2 ports detected [ 1.634000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI [ 1.639000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4 [ 1.641000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600 [ 1.662000] ata1: SATA link down (SStatus 4 SControl 300) [ 1.718000] hub 4-0:1.0: USB hub found [ 1.722000] hub 4-0:1.0: 2 ports detected [ 1.726000] Initializing USB Mass Storage driver... [ 1.731000] usbcore: registered new interface driver usb-storage [ 1.737000] USB Mass Storage support registered. [ 1.742000] i2c /dev entries driver [ 1.746000] ALSA device list: [ 1.749000] No soundcards found. [ 1.752000] TCP cubic registered [ 1.756000] NET: Registered protocol family 17 [ 1.760000] Registering the dns_resolver key type [ 1.773000] usb 1-1: new high-speed USB device number 2 using ehci-brcm [ 1.895000] hub 1-1:1.0: USB hub found [ 1.899000] hub 1-1:1.0: 3 ports detected [ 1.972000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.997000] ata2.00: ATA-8: WDC WD20EADS-32S2B0, 01.00A01, max UDMA/133 [ 2.004000] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 2.011000] usb 1-2: new high-speed USB device number 3 using ehci-brcm [ 2.037000] ata2.00: configured for UDMA/133 [ 2.042000] scsi 1:0:0:0: Direct-Access ATA WDC WD20EADS-32S 01.0 PQ: 0 ANSI: 5 [ 2.051000] sd 1:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 2.060000] sd 1:0:0:0: [sda] Write Protect is off [ 2.065000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.140000] scsi2 : usb-storage 1-2:1.0 [ 2.207000] usb 1-1.3: new high-speed USB device number 4 using ehci-brcm [ 2.291000] scsi3 : usb-storage 1-1.3:1.0 [ 2.457000] sda: sda1 [ 2.461000] sd 1:0:0:0: [sda] Attached SCSI disk [ 3.152000] scsi 2:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 [ 3.162000] scsi 2:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0 [ 3.172000] scsi 2:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0 [ 3.182000] scsi 2:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0 [ 3.300000] scsi 3:0:0:0: Direct-Access Ut165 USB2FlashStorage 0.00 PQ: 0 ANSI: 2 [ 3.317000] sd 3:0:0:0: [sdf] 15794176 512-byte logical blocks: (8.08 GB/7.53 GiB) [ 3.326000] sd 3:0:0:0: [sdf] Write Protect is off [ 3.332000] sd 3:0:0:0: [sdf] Asking for cache data failed [ 3.338000] sd 3:0:0:0: [sdf] Assuming drive cache: write through [ 3.353000] sd 3:0:0:0: [sdf] Asking for cache data failed [ 3.359000] sd 3:0:0:0: [sdf] Assuming drive cache: write through [ 3.651000] sdf: sdf1 [ 3.981000] sd 3:0:0:0: [sdf] Asking for cache data failed [ 3.987000] sd 3:0:0:0: [sdf] Assuming drive cache: write through [ 3.994000] sd 3:0:0:0: [sdf] Attached SCSI removable disk [ 6.099000] VFS: Mounted root (jffs2 filesystem) on device 31:3. [ 6.141000] devtmpfs: mounted [ 33.830000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 44.056000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 60.281000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 60.506000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 70.730000] usb 1-2: reset high-speed USB device number 3 using ehci-brcm [ 70.852000] sd 2:0:0:0: Device offlined - not ready after error recovery [ 70.859000] sd 2:0:0:0: rejecting I/O to offline device [ 70.864000] sd 2:0:0:0: rejecting I/O to offline device [ 70.870000] sd 2:0:0:0: rejecting I/O to offline device [ 70.875000] sd 2:0:0:0: [sdb] READ CAPACITY failed [ 70.880000] sd 2:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 [ 70.886000] sd 2:0:0:0: [sdb] Sense not available. [ 70.891000] sd 2:0:0:0: rejecting I/O to offline device [ 70.896000] sd 2:0:0:0: [sdb] Write Protect is off [ 70.901000] sd 2:0:0:0: rejecting I/O to offline device [ 70.906000] sd 2:0:0:0: [sdb] Asking for cache data failed [ 70.912000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 70.919000] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 71.498000] sd 2:0:0:1: [sdc] 8027712 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 71.499000] sd 2:0:0:3: [sde] Attached SCSI removable disk [ 71.500000] sd 2:0:0:2: [sdd] Attached SCSI removable disk [ 71.517000] sd 2:0:0:1: [sdc] Write Protect is off [ 71.524000] sd 2:0:0:1: [sdc] No Caching mode page present [ 71.529000] sd 2:0:0:1: [sdc] Assuming drive cache: write through [ 71.540000] sd 2:0:0:1: [sdc] No Caching mode page present [ 71.545000] sd 2:0:0:1: [sdc] Assuming drive cache: write through [ 71.553000] sdc: sdc1 [ 71.559000] sd 2:0:0:1: [sdc] No Caching mode page present [ 71.565000] sd 2:0:0:1: [sdc] Assuming drive cache: write through [ 71.571000] sd 2:0:0:1: [sdc] Attached SCSI removable disk [ 71.577000] Freeing unused kernel memory: 220k freed INIT: version 2.88 booting Displaying bootlogo. Starting udev [ 74.186000] udevd[86]: starting version 182 [ 75.137000] ath_hal: module license 'Proprietary' taints kernel. [ 75.143000] Disabling lock debugging due to kernel taint [ 75.164000] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, XR) [ 75.373000] wlan: svn r3314 [ 75.566000] ath_pci: svn r3314 [ 75.570000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 75.576000] Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies [ 76.232000] ath_rate_sample: 1.2 (svn r3314) [ 76.242000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps [ 76.247000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps [ 76.259000] wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps [ 76.267000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP [ 76.341000] ath_pci: wifi0: Atheros 2413: mem=0xd0000000, irq=33 [ 76.789000] fpga init [ 76.793000] no init ack [ 76.796000] no init ack [ 76.799000] no init ack [ 76.802000] no init ack [ 76.805000] no init ack [ 76.808000] Kernel panic - not syncing: cannot configure fpga! [ 76.808000] [ 76.815000] Rebooting in 180 seconds..