=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.09.05 17:00:29 =~=~=~=~=~=~=~=~=~=~=~= ÿ BCM97400 AB FFFFFFFF 1s Sync=1 LLMB=1 L2=1 RAC_I=1 RAC_D=1 Copy Code...34TUCV (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox DM8000 FIRST STAGE 1.10 {BO23456}  2ND STAGE OK, build #84 (2011-09-01) 0.000 - BCM board setup Configure MEMC1_2........ Done 0.039 - fp init FP version 7 detected 0.106 - ca init 0.596 - load config 1.176 - config loaded. * press [S] to enter setup OLED found! lcd: BOOT #84 - NAND PROBE: 2c da 80 95 (normal) - read config file: /boot/secondstage.conf detected jffs2 blocksize: 128kb ++++++++++++++++++++++++++++++++++++++++++++++++++++++++ dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -  done. find_inode failed for name=secondstage.conf load: Failed to find inode - failed to open /boot/secondstage.conf - failed to open /cf/autorun.bat lcd: /boot/bootlogo-dm8000.elf.gz bootlogo size: 33928 Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K !PAL_I !PAL_M !PAL_N !PAL_NC !PAL_60 !SECAM_L !SECAM_B !SECAM_G !SECAM_D !SECAM_K !SECAM_H 1080i !1080p 720p 480p 1080i_50Hz 1080p_24Hz !1080p_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p DVI_800x600p DVI_1024x768p !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_ReducedBlank !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_640x480p_85Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz !DVI_1920x1080p_60Hz_Red !Custom0 !Custom1 !Custom2 best supported mode is 25 using 1920x1080i (50.00 Hz) HDMI using colorspace: 1 create surface 1920 1080 Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard parsing JPEG header.. Virtual FB Size: 1280x720 lcd: /boot/vmlinux-3.2-dm8000.gz [ 0.000000] Linux version 3.2-dm8000 (dev@vs35) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #2 SMP Fri Aug 31 23:58:46 CEST 2012 [ 0.000000] Fetching vars from bootloader... [ 0.000000] Early serial console at MMIO32 0x10400b00 (options '115200n8') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1 [ 0.000000] Using 256 MB RAM (from straps) [ 0.000000] Fetch var 'memsize' = '154' [ 0.000000] CPU revision is: 0002a042 (Brcm4380) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] bmem: adding 102 MB RESERVED region at 154 MB (0x06600000@0x09a00000) [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00010000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5440 r8192 d15040 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw bmem=102M@154M [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.000000] Memory: 149376k/262144k available (4673k kernel code, 112768k reserved, 977k data, 220k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] Detected MIPS clock frequency: 405 MHz (202.505 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.001000] Calibrating delay loop... 403.45 BogoMIPS (lpj=201728) [ 0.013000] pid_max: default: 32768 minimum: 301 [ 0.014000] Mount-cache hash table entries: 512 [ 0.016000] SMP: Booting CPU1... [ 0.017000] CPU revision is: 0002a042 (Brcm4380) [ 0.017000] FPU revision is: 00130001 [ 0.017000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.017000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.028000] SMP: CPU1 is running [ 0.028000] Brought up 2 CPUs [ 0.029000] devtmpfs: initialized [ 0.033000] NET: Registered protocol family 16 [ 0.035000] PCI2.3->SDRAM window: 256 MB [ 0.042000] bio: create slab at 0 [ 0.044000] SCSI subsystem initialized [ 0.045000] usbcore: registered new interface driver usbfs [ 0.046000] usbcore: registered new interface driver hub [ 0.047000] usbcore: registered new device driver usb [ 0.048000] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.049000] PCI: found device 168c:001a on PCI2.3 bus, slot 1 (irq 33) [ 0.050000] pci 0000:00:01.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff] [ 0.051000] pci 0000:00:01.0: BAR 0: set to [mem 0xd0000000-0xd000ffff] (PCI address [0xd0000000-0xd000ffff]) [ 0.052000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42) [ 0.053000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff] [ 0.054000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff]) [ 0.055000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref] [ 0.056000] Switching to clocksource upg [ 0.068000] NET: Registered protocol family 2 [ 0.073000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.081000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.088000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.095000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.102000] TCP reno registered [ 0.105000] UDP hash table entries: 128 (order: 0, 4096 bytes) [ 0.111000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) [ 0.118000] NET: Registered protocol family 1 [ 0.123000] RPC: Registered named UNIX socket transport module. [ 0.129000] RPC: Registered udp transport module. [ 0.134000] RPC: Registered tcp transport module. [ 0.139000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.149000] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.157000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.167000] msgmni has been set to 291 [ 0.172000] io scheduler noop registered [ 0.176000] io scheduler cfq registered (default) [ 0.181000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.209000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 69) is a 16550A [ 0.216000] console [ttyS0] enabled, bootconsole disabled [ 0.216000] console [ttyS0] enabled, bootconsole disabled [ 0.229000] loop: module loaded [ 0.233000] brcm-pm: enabling sata clocks [ 0.237000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003) [ 0.440000] scsi0 : sata_brcmstb [ 0.444000] scsi1 : sata_brcmstb [ 0.447000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42 [ 0.455000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42 [ 0.683000] 4545 kb/s [ 0.686000] - NAND PROBE: 2c da 80 95 [ 0.690000] ONFI flash detected [ 0.693000] ONFI param page 0 valid [ 0.696000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD) [ 0.704000] Scanning device for bad blocks [ 0.788000] ata1: SATA link down (SStatus 4 SControl 300) [ 0.875000] Creating 4 MTD partitions on "MT29F2G08AAD": [ 0.880000] 0x000000000000-0x000010000000 : "complete" [ 0.887000] 0x000000000000-0x000000100000 : "loader" [ 0.893000] 0x000000100000-0x000000800000 : "boot partition" [ 0.900000] 0x000000800000-0x000010000000 : "root partition" [ 0.908000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0 [ 0.916000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:1c:b8:00) [ 0.925000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.931000] brcm-pm: enabling usb clocks [ 0.935000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.940000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.979000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300 [ 0.990000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.996000] hub 1-0:1.0: USB hub found [ 1.000000] hub 1-0:1.0: 2 ports detected [ 1.004000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI [ 1.009000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 [ 1.048000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500 [ 1.059000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 [ 1.065000] hub 2-0:1.0: USB hub found [ 1.069000] hub 2-0:1.0: 2 ports detected [ 1.073000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.080000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 1.085000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3 [ 1.092000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400 [ 1.163000] hub 3-0:1.0: USB hub found [ 1.167000] hub 3-0:1.0: 2 ports detected [ 1.172000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI [ 1.177000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4 [ 1.184000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600 [ 1.255000] hub 4-0:1.0: USB hub found [ 1.259000] hub 4-0:1.0: 2 ports detected [ 1.264000] Initializing USB Mass Storage driver... [ 1.269000] usbcore: registered new interface driver usb-storage [ 1.275000] USB Mass Storage support registered. [ 1.280000] i2c /dev entries driver [ 1.283000] ALSA device list: [ 1.286000] No soundcards found. [ 1.290000] TCP cubic registered [ 1.293000] NET: Registered protocol family 17 [ 1.298000] Registering the dns_resolver key type [ 1.310000] usb 1-1: new high-speed USB device number 2 using ehci-brcm [ 1.432000] hub 1-1:1.0: USB hub found [ 1.436000] hub 1-1:1.0: 4 ports detected [ 1.543000] usb 2-1: new high-speed USB device number 2 using ehci-brcm [ 1.667000] scsi2 : usb-storage 2-1:1.0 [ 1.995000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.163000] ata2.00: ATA-8: WDC WD10EVDS-63U8B1, 01.00A01, max UDMA/133 [ 2.170000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 2.180000] ata2.00: configured for UDMA/133 [ 2.185000] scsi 1:0:0:0: Direct-Access ATA WDC WD10EVDS-63U 01.0 PQ: 0 ANSI: 5 [ 2.194000] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2.202000] sd 1:0:0:0: [sda] Write Protect is off [ 2.207000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.224000] sda: sda1 [ 2.228000] sd 1:0:0:0: [sda] Attached SCSI disk [ 2.675000] scsi 2:0:0:0: CD-ROM Optiarc DVD RW AD-7690H 1.00 PQ: 0 ANSI: 0 [ 3.284000] Empty flash at 0x052f9c94 ends at 0x052fa000 [ 4.737000] VFS: Mounted root (jffs2 filesystem) on device 31:3. [ 4.763000] devtmpfs: mounted [ 4.767000] Freeing unused kernel memory: 220k freed INIT: version 2.88 booting Displaying bootlogo. Starting udev [ 6.758000] udevd[77]: starting version 182 [ 8.265000] stb_core: module license 'Proprietary' taints kernel. [ 8.271000] Disabling lock debugging due to kernel taint [ 8.629000] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, XR) [ 8.840000] wlan: svn r3314 [ 8.982000] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda caddy [ 8.990000] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 9.220000] module ath_pci: dangerous R_MIPS_LO16 REL relocation [ 9.220000] module snd_timer: dangerous R_MIPS_LO16 REL relocation [ 9.272000] module dreambox_rc2: dangerous R_MIPS_LO16 REL relocation [ 9.533000] module ipv6: dangerous R_MIPS_LO16 REL relocation [ 9.545000] 4004512 ms: [ 9.614000] 67 ms: 12 mkdir /dev/shm..... [ 9.783000] Empty flash at 0x00328b60 ends at 0x00329000 [ 9.894000] 277 ms: 14 [ 10.448000] 551 ms: 16 [ 10.503000] 52 ms: 18 [ 10.530000] 25 ms: 20 Configuring network interfaces... udhcpc (v1.19.4) started Sending discover... Sending select for 192.168.178.20... Lease of 192.168.178.20 obtained, lease time 864000 /etc/udhcpc.d/50default: Adding DNS 192.168.178.1 done. [ 11.577000] 1044 ms: 22 rdate: current time matches remote time Starting rdate t[ 11.960000] 380 ms: 24 imesync...: Sync doneStarting rpcbind... [ 12.165000] module ipv6: dangerous R_MIPS_LO16 REL relocation rpcbind: cannot create socket for udp6 [ 12.216000] module ipv6: dangerous R_MIPS_LO16 REL relocation rpcbind: cannot create socket for tcp6 [ 12.335000] module ipv6: dangerous R_MIPS_LO16 REL relocation Mounting /etc/enigma2/automounts.xml... [ 17.846000] module cifs: dangerous R_MIPS_LO16 REL relocation mount: mounting //192.168.178.1/FRITZ.NAS on /media/net/FRITZNAS failed: No such device [ 17.913000] 5951 ms: 26 net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter[ 17.985000] 69 ms: 28 = 1 Starting tpmd. [ 18.022000] 34 ms: 30 INIT: Entering runlevel: 3 Starting system message bus: dbus. [ 18.821000] 796 ms: 33 Starting Dropbear SSH server: dropbear. [ 18.878000] 55 ms: 34 Starting automounter: loading autofs4 kernel module,[ 18.989000] module autofs4: dangerous R_MIPS_LO16 REL relocation modprobe: can't load module autofs4 (kernel/fs/autofs4/autofs4.ko): invalid module format done. [ 19.919000] 1039 ms: 35 [ 19.988000] 66 ms: 36 Starting dbttcd. [ 20.033000] 43 ms: 38 Starting default emu. [ 20.072000] 37 ms: 39 creating NFS state directory: done NFSD Modul loaded.... NFSD Mounted.... RPCBIND Running.... starting 8 nfsd kernel threads: wdog[607]: dbttcd exited with status 256 [ 20.756000] module nfsd: dangerous R_MIPS_LO16 REL relocation rpc.nfsd: Unable to access /proc/fs/nfsd errno 2 (No such file or directory). Please try, as root, 'mount -t nfsd nfsd /proc/fs/nfsd' and then restart rpc.nfsd to correct the problem done starting mountd: [ 21.000000] module ipv6: dangerous R_MIPS_LO16 REL relocation rpc.mountd: svc_tli_create: could not open connection for udp6 [ 21.069000] CPU 0 Unable to handle kernel paging request at virtual address c08200b8, epc == 8000b498, ra == 8000b4d0 [ 21.079000] Oops[#1]: [ 21.079000] Cpu 0 [ 21.079000] $ 0 : 00000000 30008700 88fc0100 c08200b8 [ 21.079000] $ 4 : 88fc0100 3c108043 00008043 00000001 [ 21.079000] $ 8 : c08c164c 000000bc 80494788 89631800 [ 21.079000] $12 : 00000003 00000000 00000001 6d726678 [ 21.079000] $16 : c08e70bc 26100000 805c0000 c09294c4 [ 21.079000] $20 : 88fc0100 8042f0e0 00000000 ffff0000 [ 21.079000] $24 : 00000008 8000fd50 [ 21.079000] $28 : 88d90000 88d91e08 8042f0e0 8000b4d0 [ 21.079000] Hi : 00000000 [ 21.079000] Lo : 000050f8 [ 21.079000] epc : 8000b498 apply_r_mips_lo16_rel+0x78/0x120 [ 21.079000] Tainted: P O [ 21.079000] ra : 8000b4d0 apply_r_mips_lo16_rel+0xb0/0x120 [ 21.079000] Status: 30008703 KERNEL EXL IE [ 21.079000] Cause : 00800008 [ 21.079000] BadVA : c08200b8 [ 21.079000] PrId : 0002a042 (Brcm4380) [ 21.079000] Modules linked in: snd_page_alloc tu1216(O) max4397(P) cu1216mk3(P) alps_bsbe1_c01a(P) bcm4506(P) helper(O) cxd1981(P) alps_bsbe1(O) sr_mod wlan(O) lnb_ctrl(P) cdrom ath_hal(P) stv0299 lcd(P) stb_core(P) [ 21.079000] Process modprobe (pid: 643, threadinfo=88d90000, task=88e44d98, tls=77f518d0) [ 21.079000] Stack : 26006c65 c08e70b8 00000001 c08c1674 c08cd980 00000002 c08c1674 c08c15fc [ 21.079000] c09294c4 80494770 c08c1cdc c08c7c0c 00000002 8000b7a4 c08cd950 00005b5c [ 21.079000] 00000000 80068e88 c09294c4 00000003 00ac3750 00000078 805671b4 c09295ec [ 21.079000] 00000004 c09294d0 00000009 8006a0c0 00000000 00000004 77d94000 00030002 [ 21.079000] c09294c4 890cdc38 89014118 89583cc0 00000010 88f50840 88f50840 890cdc38 [ 21.079000] ... [ 21.079000] Call Trace: [ 21.079000] [<8000b498>] apply_r_mips_lo16_rel+0x78/0x120 [ 21.079000] [<8000b7a4>] apply_relocate+0xf0/0x18c [ 21.079000] [<8006a0c0>] sys_init_module+0x11c8/0x1e28 [ 21.079000] [<8000c61c>] stack_done+0x20/0x40 [ 21.079000] [ 21.079000] [ 21.079000] Code: 02801021 8c430004 00402021 <8c650000> 00053400 00d53021 00d63021 30c78000 0007382b [ 21.270000] ---[ end trace 7d1c1ad0b5e96090 ]--- rpc.mountd: svc_tli_create: could not open connection for tcp6 [ 21.383000] module ipv6: dangerous R_MIPS_LO16 REL relocation rpc.mountd: svc_tli_create: could not open connection for udp6 [ 21.462000] module ipv6: dangerous R_MIPS_LO16 REL relocation rpc.mountd: svc_tli_create: could not open connection for tcp6 wdog[607]: dbttcd exited with status 256 [ 21.953000] module ipv6: dangerous R_MIPS_LO16 REL relocation rpc.mountd: svc_tli_create: could not open connection for udp6 [ 22.725000] module ipv6: dangerous R_MIPS_LO16 REL relocation rpc.mountd: svc_tli_create: could not open connection for tcp6 done starting statd: wdog[607]: dbttcd exited with status 256 [ 22.852000] Kernel bug detected[#2]: [ 22.852000] Cpu 0 [ 22.852000] $ 0 : 00000000 30008700 00000001 800558b8 [ 22.852000] $ 4 : 88fc0d14 00000000 8120367c 30008701 [ 22.852000] $ 8 : 00000000 81206774 00000007 00000000 [ 22.852000] $12 : 00000007 0000000e 00000020 804b0340 [ 22.852000] $16 : 88fc0d14 8056cf40 894e7ea4 00000002 [ 22.852000] $20 : 8120368c 812036a4 0000000a 88daf3c0 [ 22.852000] $24 : 0000d290 8000c4a0 [ 22.852000] $28 : 88f40000 88f41e20 805bb140 8007c4e0 [ 22.852000] Hi : 00000000 [ 22.852000] Lo : 00a86000 [ 22.852000] epc : 800558d0 release_tgcred_rcu+0x18/0x40 [ 22.852000] Tainted: P D O [ 22.852000] ra : 8007c4e0 __rcu_process_callbacks+0x1c0/0x490 [ 22.852000] Status: 30008703 KERNEL EXL IE [ 22.852000] Cause : 00800034 [ 22.852000] PrId : 0002a042 (Brcm4380) [ 22.852000] Modules linked in: snd_page_alloc tu1216(O) max4397(P) cu1216mk3(P) alps_bsbe1_c01a(P) bcm4506(P) helper(O) cxd1981(P) alps_bsbe1(O) sr_mod wlan(O) lnb_ctrl(P) cdrom ath_hal(P) stv0299 lcd(P) stb_core(P) [ 22.852000] Process dbttcd (pid: 670, threadinfo=88f40000, task=884289b8, tls=779466a0) [ 22.852000] Stack : 8120368c 00000016 8120368c 8056cf40 8120368c 8007c4e0 00000100 8003cf60 [ 22.852000] 81203604 8056ce40 00000100 805671b4 805606a4 00000100 80560680 00000008 [ 22.852000] 00000000 805c8540 805671b4 8007c7ec 80560680 00000009 00000000 805c8540 [ 22.852000] 00000000 8003541c 00000003 00000001 00000020 fffff7ff 00000003 77ba0eb8 [ 22.852000] 00000009 800794a8 30008700 00000002 00000003 00000001 00000020 fffff7ff [ 22.852000] ... [ 22.852000] Call Trace: [ 22.852000] [<800558d0>] release_tgcred_rcu+0x18/0x40 [ 22.852000] [<8007c4e0>] __rcu_process_callbacks+0x1c0/0x490 [ 22.852000] [<8007c7ec>] rcu_process_callbacks+0x3c/0x70 [ 22.852000] [<8003541c>] __do_softirq+0x104/0x1d4 [ 22.852000] [<800357ec>] do_softirq+0xa4/0xac [ 22.852000] [<80035acc>] irq_exit+0xb0/0xd8 [ 22.852000] [<800026e4>] plat_irq_dispatch+0xa8/0x104 [ 22.852000] [<80004824>] ret_from_irq+0x0/0x4 [ 22.852000] [ 22.852000] [ 22.852000] Code: 8c82ffec 00808021 0002102b [ 22.852000] 0c0a2303 8c84fff8 0c0a2303 8e04fffc 2604ffec [ 23.060000] ---[ end trace 7d1c1ad0b5e96091 ]--- [ 23.064000] Kernel panic - not syncing: Fatal exception in interrupt [ 23.071000] Rebooting in 180 seconds..