=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.02.04 18:23:38 =~=~=~=~=~=~=~=~=~=~=~= BCM97400 AB FFFFFFFF 1s Sync=0 LLMB=0 L2=0 RAC_I=0 RAC_D=0 Copy Code...34TUCV (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox D M8000 FIRST STAGE 1.00 {BO23456}  2ND STAGE OK, build #76 (20091014) 0.000 - BCM board setup Configure MEMC1_2........ Done 0.039 - fp init FP version 7 detected 0.106 - ca init 0.823 - load config 1.403 - config loaded. * press [S] to enter setup OLED found! BOOT #76(20091014) - NAND PROBE: 2c da 80 95 (normal) detected jffs2 blocksize: 128kb ++++++++++++++++++++++++ dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / -  done. /flash/bootlogo.elf bootlogo size: 170039 *** BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1920 x 1080 (1080p) Available modes: 1920x1080i_60.00Hz 1920x1080p_60.00Hz 1280x720p_60.00Hz 720x480p_59.94Hz 1920x1080i_50.00Hz 1920x1080p_24.00Hz 1920x1080p_25.00Hz 1920x1080p_30.00Hz 1920x1080p_50.00Hz 1920x1080i_50.00Hz 1280x720p_24.00Hz 1280x720p_50.00Hz 720x576p_50.00Hz 640x480p_60.00Hz 1280x720p_50.00Hz 1280x720p_60.00Hz 1280x720p_60.00Hz 1280x720p_70.00Hz 1280x720p_72.00Hz 1280x720p_75.00Hz 1280x720p_85.00Hz 1920x1080p_60.00Hz 1920x1080p_60.00Hz 1920x1080p_50.00Hz using 1920x1080i (50.00 Hz) HDMI using colorspace: 1 *** BHDM: Waiting to transition to HDMI mode... 000CB001 0 *** BHDM: Wating to transition to HDMI mode... 000CB001 0 *** BHDM: Waiting to transition to HDMI mode... 000CB001 0 *** BHDM: HDMI Output Mode: HDMI (Audio+Video) create surface 1920 1080 Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard parsing JPEG header.. JPEG Size: 1280x720 /flash/vmlinux.gz <5>Linux version 2.6.18-7.4-dm8000 (tmbinc@pepe.multimedia-labs.de) (gcc version 4.4.3 (GCC) ) #1 SMP Sat Jan 29 11:53:56 UTC 2011 Fetching vars from bootloader... none present, using defaults. Detected 256 MB on MEMC0 (strap 0x2219c310) <4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824 Default command line = root=/dev/mtdblock3 rootfstype=jffs2 rw console=null 2 831ffed8 83040e98 g_board_RAM_size=256MB Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1 CPU revision is: 0002a042 FPU revision is: 00130001 Determined physical RAM map: memory: 10000000 @ 00000000 (usable) ---> memsize from bootloader: 158 User-defined physical RAM map: node [00000000, 09e00000: RAM] node [09e00000, 06200000: RSVD] <5>Reserving 98 MB upper memory starting at 09e00000 <7>On node 0 totalpages: 65536 <7> DMA zone: 65536 pages, LIFO batch:15 Built 1 zonelists. Total pages: 65536 <5>Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw before init RAC 0x01e0701f 0x0000000f 0x2fff0000 after init RAC 0x01e0705f 0x0000000f 0x2fff0000 [4294667.296000] ======> Before RAC_init:$22s5=00000020, $22s6(CBA)=11f0000c [4294667.296000] @B1F0_001C=00000001, @B1F0_0004=2fff0000, @B1F0_0000=01e0701f, @B1F0_0008=0000000f [4294667.296000] CBA = 11f00000 VALUE = 255 PAR_VAL2 = 0fff0000 [4294667.296000] RAC0 = b1f00000 RAC1 = b1f00008 RAC_RANGE = b1f00004 [4294667.296000] RAC_VALUE = 00087000 [4294667.296000] ******* Using CFE setting for RAC [4294667.296000] ******* $22s0=e30e3406, $22s5=00000020, $22s6=11f0000c [4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes. [4294667.296000] Primary data cache 64kB, 4-way, linesize 64 bytes. [4294667.296000] Synthesized TLB refill handler (23 instructions). [4294667.296000] Synthesized TLB load handler fastpath (37 instructions). [4294667.296000] Synthesized TLB store handler fastpath (37 instructions). [4294667.296000] Synthesized TLB modify handler fastpath (36 instructions). [4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes) [4294667.296000] Found MIPS counter frequency: 203 Mhz [4294667.296000] Using 202.501 MHz high precision timer. [4294667.296000] Console: colour dummy device 80x25 [4294667.400000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [4294667.406000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [4294667.425000] Memory: 155776k/262144k available (2622k kernel code, 106152k reserved, 562k data, 136k init, 0k highmem) [4294667.457000] Mount-cache hash table entries: 512 [4294667.461000] Checking for 'wait' instruction... available. [4294667.466000] plat_prepare_cpus: ENABLING 2nd Thread... [4294667.471000] TP0: prom_boot_secondary: Kick off 2nd CPU... [4294667.476000] CPU revision is: 0002a042 [4294667.476000] FPU revision is: 00130001 [4294667.476000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes. [4294667.476000] Primary data cache 64kB, 4-way, linesize 64 bytes. [4294667.476000] Synthesized TLB refill handler (23 instructions). [4294667.497000] Brought up 2 CPUs [4294667.585000] migration_cost=1000 [4294667.590000] NET: Registered protocol family 16 [4294667.595000] registering PCI controller with io_map_base unset [4294667.600000] registering PCI controller with io_map_base unset [4294667.606000] SCSI subsystem initialized [4294667.610000] usbcore: registered new driver usbfs [4294667.613000] usbcore: registered new driver hub [4294667.617000] NET: Registered protocol family 2 [4294667.634000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [4294667.641000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [4294667.647000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [4294667.653000] TCP: Hash tables configured (established 8192 bind 4096) [4294667.659000] TCP reno registered [4294667.662000] brcm-pm: disabling power to USB block [4294667.666000] brcm-pm: disabling power to ENET block [4294667.670000] brcm-pm: disabling power to SATA block [4294667.675000] JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc. [4294667.682000] Initializing Cryptographic API [4294667.686000] io scheduler noop registered [4294667.689000] io scheduler anticipatory registered [4294667.693000] io scheduler deadline registered [4294667.697000] io scheduler cfq registered (default) [4294667.704000] Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled [4294667.712000] serial8250: ttyS0 at MMIO 0x0 (irq = 65) is a 16550A [4294667.717000] brcm-pm: enabling power to ENET block [4294667.721000] Broadcom BCM7400 P42 Ethernet Network Device v2.0 Jan 29 2011 11:53:12 [4294667.728000] SUNDRY revision = 74000032, have IP Hdr Opt=1 [4294667.733000] Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg) [4294669.391000] brcm-pm: enabling power to SATA block [4294669.411000] ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42 [4294669.419000] ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42 [4294669.427000] scsi0 : sata_svw [4294669.732000] ata1: SATA link down (SStatus 4 SControl 300) [4294669.768000] ATA: abnormal status 0x7F on port 0xb051001c [4294669.774000] scsi1 : sata_svw [4294670.084000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl F0000) [4294670.096000] ata2.00: ATA-8, max UDMA/133, 3907029168 sectors: LBA48 NCQ (depth 0/32) [4294670.109000] ata2.00: configured for UDMA/133 [4294670.114000] Vendor: ATA Model: SAMSUNG HD203WI Rev: 1AN1 [4294670.120000] Type: Direct-Access ANSI SCSI revision: 05 [4294670.126000] SCSI device sda: 3907029168 512-byte hdwr sectors (2000399 MB) [4294670.133000] sda: Write Protect is off [4294670.136000] SCSI device sda: drive cache: write back [4294670.140000] SCSI device sda: 3907029168 512-byte hdwr sectors (2000399 MB) [4294670.146000] sda: Write Protect is off [4294670.149000] SCSI device sda: drive cache: write back [4294670.154000] sda: sda1 [4294670.160000] sd 1:0:0:0: Attached scsi disk sda [4294670.164000] sd 1:0:0:0: Attached scsi generic sg0 type 0 [4294670.387000] 4587 kb/s [4294670.389000] - NAND PROBE: 2c da 80 95 [4294670.392000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Unknown NAND 256MiB 3,3V 8-bit) [4294670.400000] Scanning device for bad blocks [4294670.486000] Creating 7 MTD partitions on "NAND 256MiB 3,3V 8-bit": [4294670.492000] 0x0000000000000000-0x0000000010000000 : "complete" [4294670.497000] 0x0000000000000000-0x0000000000100000 : "loader" [4294670.503000] 0x0000000000100000-0x0000000000400000 : "boot partition" [4294670.508000] 0x0000000000400000-0x0000000004000000 : "root partition" [4294670.514000] 0x0000000004000000-0x0000000008000000 : "home partition" [4294670.520000] 0x0000000008000000-0x000000000f800000 : "unused partition" [4294670.526000] 0x000000000f800000-0x0000000010000000 : "preset partition" [4294670.532000] ehci_hcd_brcm_init: Initializing 2 EHCI controller(s) [4294670.538000] brcm-pm: enabling power to USB block [4294670.542000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0) [4294670.549000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller [4294670.555000] - USB h/w setup mode [4294670.555000] - USB power enable set for active LOW mode [4294670.563000] brcm-ehci brcm-ehci.0: BRCM EHCI [4294670.567000] brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1 [4294670.574000] brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300 [4294670.579000] brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 [4294670.585000] usb usb1: configuration #1 chosen from 1 choice [4294670.591000] hub 1-0:1.0: USB hub found [4294670.594000] hub 1-0:1.0: 2 ports detected [4294670.698000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1) [4294670.706000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller [4294670.712000] brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI [4294670.716000] brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2 [4294670.723000] brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500 [4294670.728000] brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 [4294670.736000] usb usb2: configuration #1 chosen from 1 choice [4294670.741000] hub 2-0:1.0: USB hub found [4294670.744000] hub 2-0:1.0: 2 ports detected [4294670.848000] ohci_hcd_brcm_init: Initializing 2 OHCI controller(s) [4294670.854000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0) [4294670.861000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller [4294670.867000] - Resetting at b0480408 [4294670.870000] <-- brcm_start_hc [4294670.872000] brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI [4294670.876000] brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3 [4294670.883000] brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400 [4294670.912000] usb 1-1: new high speed USB device using brcm-ehci and address 2 [4294670.943000] usb usb3: configuration #1 chosen from 1 choice [4294670.949000] hub 3-0:1.0: USB hub found [4294670.952000] hub 3-0:1.0: 2 ports detected [4294671.033000] usb 1-1: configuration #1 chosen from 1 choice [4294671.039000] hub 1-1:1.0: USB hub found [4294671.042000] hub 1-1:1.0: 3 ports detected [4294671.056000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1) [4294671.064000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller [4294671.070000] - Resetting at b0480608 [4294671.073000] <-- brcm_start_hc [4294671.075000] brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI [4294671.079000] brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4 [4294671.086000] brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600 [4294671.146000] usb usb4: configuration #1 chosen from 1 choice [4294671.152000] hub 4-0:1.0: USB hub found [4294671.155000] hub 4-0:1.0: 2 ports detected [4294671.259000] Initializing USB Mass Storage driver... [4294671.358000] usb 1-2: new high speed USB device using brcm-ehci and address 3 [4294671.481000] usb 1-2: configuration #1 chosen from 1 choice [4294671.693000] usb 2-1: new high speed USB device using brcm-ehci-1 and address 2 [4294671.823000] usb 2-1: configuration #1 chosen from 1 choice [4294671.830000] scsi2 : SCSI emulation for USB Mass Storage devices [4294671.836000] scsi3 : SCSI emulation for USB Mass Storage devices [4294671.842000] usbcore: registered new driver usb-storage [4294671.842000] USB Mass Storage support registered. [4294671.842000] i2c /dev entries driver [4294671.855000] TCP bic registered [4294671.858000] NET: Registered protocol family 1 [4294671.862000] NET: Registered protocol family 17 [4294676.836000] isa bounce pool size: 16 pages [4294676.842000] Vendor: Generic Model: USB SD Reader Rev: 1.00 [4294676.849000] Type: Direct-Access ANSI SCSI revision: 00 [4294676.877000] Vendor: TEAC Model: DV-W28S-R Rev: 1.0A [4294676.885000] Type: CD-ROM ANSI SCSI revision: 00 [4294677.126000] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [4294677.134000] Uniform CD-ROM driver Revision: 3.20 [4294677.140000] sr 3:0:0:0: Attached scsi generic sg1 type 5 [4294677.299000] SCSI device sdb: 3970048 512-byte hdwr sectors (2033 MB) [4294677.307000] sdb: Write Protect is off [4294677.311000] sdb: assuming drive cache: write through [4294678.428000] VFS: Mounted root (jffs2 filesystem). [4294678.433000] Freeing unused kernel memory: 136k freed [4294678.442000] SCSI device sdb: 3970048 512-byte hdwr sectors (2033 MB) [4294678.449000] sdb: Write Protect is off [4294678.453000] sdb: assuming drive cache: write through [4294678.457000] sdb: sdb1 [4294678.461000] sd 2:0:0:0: Attached scsi removable disk sdb [4294678.466000] sd 2:0:0:0: Attached scsi generic sg2 type 0 [4294678.472000] Vendor: Generic Model: USB CF Reader Rev: 1.01 [4294678.478000] Type: Direct-Access ANSI SCSI revision: 00<4>mtd->read(0x434 bytes from 0x14503cc) returned ECC error [4294678.482000] JFFS2 notice: (1) jffs2_get_inode_nodes: Node header CRC failed at 0x14503cc. {a53a,d7ab,a9d54f78,2f169831} [4294678.501000] [4294678.506000] sd 2:0:0:1: Attached scsi removable disk sdc [4294678.512000] sd 2:0:0:1: Attached scsi generic sg3 type 0 [4294678.517000] Vendor: Generic Model: USB SM Reader Rev: 1.02 [4294678.523000] Type: Direct-Access ANSI SCSI revision: 00 [4294678.534000] sd 2:0:0:2: Attached scsi removable disk sdd [4294678.539000] sd 2:0:0:2: Attached scsi generic sg4 type 0 [4294678.545000] Vendor: Generic Model: USB MS Reader Rev: 1.03 [4294678.551000] Type: Direct-Access ANSI SCSI revision: 00 [4294678.561000] sd 2:0:0:3: Attached scsi removable disk sde [4294678.567000] sd 2:0:0:3: Attached scsi generic sg5 type 0