CPU 01 Dreambox DM920 AVS init... AVS init OK AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2 a002b00 AVS load_code offset =00051000 LOADED AVS: overtemp mon ON single board select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500 MEMSYS-STD SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0 MCB: FLEX AVS start:status=000000ff STB: Current voltage=0000037e(894) temperature=000066ac(26284) PV=00000342(834) MV=0000037e(894) AVS FW rev=30333278 [0.3.2.x] OK DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK Sdram Scramble OTP = 0x00000001 Sdram Scramble OK select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b BFW load mode OTP = 0x0000000f bfw_hash_locked = 0x00000000 BFW key3 OK, BFW load OK BFW v2.1.0 COPY CODE... DONE MICH: disable success SSBL PINMUX CACHE FLUSH OK MMU ON CACHE FLUSH OK _fbss 07080d30 _ebss 0713ddd0 _end 0713ddf0 HEAP @ 07200000 STACK @ 09300000 ARCH: CONFIG OK CLR BSS 07080d30 to 0713ddd0 OK CLR SRAM OK CACHE FLUSH OK CPU CLKSET OK GO! ,/ ,'/___, BOLT v1.18 v1.18 LOCAL BUILD .'__ ,' (2017-11-08 00:35:37 cynric@cynric-VirtualBox) /,' Copyright (C) 2017 Broadcom /' Board: BCM97252SSFF SYS_CTRL: product=72521, family=7439b1, strap=000000b2, otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovi sion_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000) otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020) CPU: 2x B15 [420f00f3] 1719 MHz SCB: 432 MHz DDR0 @ 1067MHz, DDR1 @ 1067MHz RESET CAUSE: 0x000001 power_on (1 of 23 possible causes) CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages CS1: NAND: unrecognized ID: 0xffff 0xffffffff RTS0: 0x1101004, 256 clients, ok RTS1: 0x1181004, 256 clients, ok BOX MODE: 5 card if inited set pwm to 0/255 disp id ffff load image AVS: park check AVS: temperature monitoring enabled AVS: STB: V=0.892V, T=+27.258C, PV=0.834V, MV=0.894V, FW=30333278 [0.3.2.x] USB otp=00000040 USB @ 0xf0470200: IPP is active low, IOC is negative polarity init fp ATR length 18b. TPM version 1 found card in unknown state ca valid! set pwm to 200/255 Normal bootup Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:(null) Reading 4249440 bytes from zImage........... Starting program at 0x8000 (DTB @ 0x7728000) 32 bit boot... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.14-1.17-dm920 (merlinbuild@merlinbuild) (gcc vers ion 5.3.0 (GCC) ) #1 SMP Tue Oct 27 15:37:01 CET 2020 [ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: BCM97252SSFF [ 0.000000] moving dtb from 0x0000000007728000 to 0x0000000000839e70 [ 0.000000] bmem: Reserved 640 MiB at 0x0000000018000000 [ 0.000000] bmem: Reserved 384 MiB at 0x0000000080000000 [ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] MCP: Enabling write pairing [ 0.000000] PERCPU: Embedded 8 pages/cpu @cdfc0000 s8384 r8192 d16192 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 523776 [ 0.000000] Kernel command line: bmem=640M@384M bmem=384M@2048M console=ttyS0 ,1000000 root=/dev/mmcblk0p2 rootwait rootfstype=ext4 coherent_pool=2M [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 1006896K/2097152K available (6114K kernel code, 214K rwda ta, 1600K rodata, 244K init, 208K bss, 1073872K reserved, 16384K cma-reserved, 7 86428K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0790cec (7716 kB) [ 0.000000] .init : 0xc0791000 - 0xc07ce0c0 ( 245 kB) [ 0.000000] .data : 0xc07d0000 - 0xc0805b20 ( 215 kB) [ 0.000000] .bss : 0xc0805b28 - 0xc0839e70 ( 209 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93) [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64) [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95) [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58) [ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt). [ 0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 25451 65795328ns [ 0.000010] Switching to timer-based delay loop [ 0.000235] Console: colour dummy device 80x30 [ 0.000256] Calibrating delay loop (skipped), value calculated using timer fr equency.. 54.00 BogoMIPS (lpj=27000) [ 0.000264] pid_max: default: 32768 minimum: 301 [ 0.000357] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000362] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.005882] Initializing cgroup subsys devices [ 0.005895] Initializing cgroup subsys freezer [ 0.005902] Initializing cgroup subsys net_cls [ 0.005931] CPU: Testing write buffer coherency: ok [ 0.006147] CPU0: update cpu_power 1024 [ 0.006153] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006199] Setting up static identity map for 0x5d5ab8 - 0x5d5b10 [ 0.007436] CPU1: Booted secondary processor [ 0.007454] CPU1: update cpu_power 1024 [ 0.007457] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.007530] Brought up 2 CPUs [ 0.007540] SMP: Total of 2 processors activated (108.00 BogoMIPS). [ 0.007544] CPU: All CPU(s) started in SVC mode. [ 0.007930] devtmpfs: initialized [ 0.011551] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0 [ 0.012144] regulator-dummy: no parameters [ 0.012315] NET: Registered protocol family 16 [ 0.013248] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.013436] cpuidle: using governor ladder [ 0.013441] cpuidle: using governor menu [ 0.014572] irq: no irq domain found for /rdb/interrupt-controller@f040a700 ! [ 0.014655] irq: no irq domain found for /rdb/interrupt-controller@f0417380 ! [ 0.016333] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] regist ered [ 0.016404] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] regist ered [ 0.016470] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] regist ered [ 0.016533] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] regist ered [ 0.016596] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] regist ered [ 0.016661] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] regist ered [ 0.016725] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] regist ered [ 0.016786] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] regist ered [ 0.016848] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] regist ered [ 0.016916] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] regist ered [ 0.016982] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] regist ered [ 0.017043] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] regist ered [ 0.017120] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] regist ered [ 0.017185] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] regist ered [ 0.017487] irq: no irq domain found for /rdb/interrupt-controller@f0417380 ! [ 0.017713] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478 [ 0.022031] bio: create slab at 0 [ 0.022336] brcmstb-gpio f040a600.gpio: Couldn't get IRQ. Enable CONFIG_BCM71 20_L2_IRQ if you want GPIO interrupt support [ 0.022360] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159) [ 0.022388] brcmstb-gpio f0417400.gpio: Couldn't get IRQ. Enable CONFIG_BCM71 20_L2_IRQ if you want GPIO interrupt support [ 0.022401] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223) [ 0.022749] SCSI subsystem initialized [ 0.022963] usbcore: registered new interface driver usbfs [ 0.022993] usbcore: registered new interface driver hub [ 0.023052] usbcore: registered new device driver usb [ 0.023071] media: Linux media interface: v0.10 [ 0.023098] Linux video capture interface: v2.00 [ 0.023150] pps_core: LinuxPPS API ver. 1 registered [ 0.023153] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 0.023164] PTP clock support registered [ 0.023380] Advanced Linux Sound Architecture Driver Initialized. [ 0.023661] Bluetooth: Core ver 2.18 [ 0.023676] NET: Registered protocol family 31 [ 0.023680] Bluetooth: HCI device and connection manager initialized [ 0.023688] Bluetooth: HCI socket layer initialized [ 0.023694] Bluetooth: L2CAP socket layer initialized [ 0.023700] Bluetooth: SCO socket layer initialized [ 0.024090] Switched to clocksource arch_sys_counter [ 0.024100] cfg80211: Calling CRDA to update world regulatory domain [ 0.028466] thermal thermal_zone0: failed to read out thermal zone 0 [ 0.028551] NET: Registered protocol family 2 [ 0.028954] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.028971] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.028993] TCP: Hash tables configured (established 2048 bind 2048) [ 0.029027] TCP: reno registered [ 0.029034] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.029046] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.029185] NET: Registered protocol family 1 [ 0.029412] RPC: Registered named UNIX socket transport module. [ 0.029417] RPC: Registered udp transport module. [ 0.029421] RPC: Registered tcp transport module. [ 0.029424] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.030028] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.030366] bounce pool size: 64 pages [ 0.030883] NFS: Registering the id_resolver key type [ 0.030912] Key type id_resolver registered [ 0.030916] Key type id_legacy registered [ 0.030927] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.031057] SGI XFS with ACLs, security attributes, realtime, large block/ino de numbers, no debug enabled [ 0.031372] msgmni has been set to 462 [ 0.032116] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 51) [ 0.032123] io scheduler noop registered [ 0.032142] io scheduler cfq registered (default) [ 0.032366] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259 [ 0.032649] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device T ree [ 0.098368] brcmstb_memc f1102000.memc-ddr: registered [ 0.098394] brcmstb_memc f1182000.memc-ddr: registered [ 0.098595] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.099418] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A [ 0.196045] console [ttyS0] enabled [ 0.197292] loop: module loaded [ 0.197929] ahci brcmstb-ahci.0: can't get clock [ 0.198545] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled [ 0.210105] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 i mpl platform mode [ 0.211100] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum p art [ 0.213740] scsi0 : ahci_platform [ 0.214378] scsi1 : ahci_platform [ 0.214882] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x1 00 irq 91 [ 0.215801] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x1 80 irq 91 [ 0.217218] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address [ 0.217992] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated [ 0.219123] m25p80 spi32766.0: found mx25l25635e, expected m25p80 [ 0.219831] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address [ 0.220564] m25p80 spi32766.0: mx25l25635e (32768 Kbytes) [ 0.221211] 5 ofpart partitions found on MTD device spi32766.0 [ 0.221880] Creating 5 MTD partitions on "spi32766.0": [ 0.222478] 0x000000000000-0x000000200000 : "flash0.bolt" [ 0.223579] 0x000000200000-0x000000220000 : "flash0.nvram" [ 0.224615] 0x000000220000-0x000000240000 : "flash0.devtree" [ 0.225680] 0x000000240000-0x000001000000 : "flash0.recovery" [ 0.226741] 0x000000000000-0x000002000000 : "flash0" [ 0.228000] libphy: Fixed MDIO Bus: probed [ 0.228605] tun: Universal TUN/TAP device driver, 1.6 [ 0.229194] tun: (C) 1999-2004 Max Krasnyansky [ 0.230231] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001 [ 0.244096] libphy: bcmgenet MII bus: probed [ 0.264975] xhci-brcm: xHCI BRCM driver [ 0.265497] xhci-brcm f0471000.xhci_v2: xHCI Host Controller [ 0.266168] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1 [ 0.267356] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000 [ 0.268201] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.268981] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.269817] usb usb1: Product: xHCI Host Controller [ 0.270382] usb usb1: Manufacturer: Linux 3.14-1.17-dm920 xhci-hcd [ 0.271103] usb usb1: SerialNumber: f0471000.xhci_v2 [ 0.271983] hub 1-0:1.0: USB hub found [ 0.272448] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 0.273380] xhci-brcm f0471000.xhci_v2: xHCI Host Controller [ 0.274039] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2 [ 0.275069] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 0.275856] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.276689] usb usb2: Product: xHCI Host Controller [ 0.277261] usb usb2: Manufacturer: Linux 3.14-1.17-dm920 xhci-hcd [ 0.277970] usb usb2: SerialNumber: f0471000.xhci_v2 [ 0.278817] hub 2-0:1.0: USB hub found [ 0.279275] hub 2-0:1.0: 2 ports detected [ 0.280039] ehci-brcm: EHCI BRCM driver [ 0.280566] ehci-brcm f0470300.ehci_v2: EHCI Host Controller [ 0.281233] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3 [ 0.292247] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300 [ 0.298102] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00 [ 0.298911] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.299698] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.300532] usb usb3: Product: EHCI Host Controller [ 0.301099] usb usb3: Manufacturer: Linux 3.14-1.17-dm920 ehci_hcd [ 0.301808] usb usb3: SerialNumber: f0470300.ehci_v2 [ 0.302656] hub 3-0:1.0: USB hub found [ 0.303116] hub 3-0:1.0: 1 port detected [ 0.303759] ehci-brcm f0470500.ehci_v2: EHCI Host Controller [ 0.304425] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4 [ 0.315423] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500 [ 0.322096] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00 [ 0.322898] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.323686] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.324520] usb usb4: Product: EHCI Host Controller [ 0.325087] usb usb4: Manufacturer: Linux 3.14-1.17-dm920 ehci_hcd [ 0.325796] usb usb4: SerialNumber: f0470500.ehci_v2 [ 0.326622] hub 4-0:1.0: USB hub found [ 0.327072] hub 4-0:1.0: 1 port detected [ 0.327113] ata1: SATA link down (SStatus 0 SControl 300) [ 0.328387] ohci-brcm: OHCI BRCM driver [ 0.328883] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller [ 0.329553] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5 [ 0.330478] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400 [ 0.386213] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.386992] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.387827] usb usb5: Product: BRCM OHCI controller [ 0.388394] usb usb5: Manufacturer: Linux 3.14-1.17-dm920 ohci_hcd [ 0.389109] usb usb5: SerialNumber: f0470400.ohci_v2 [ 0.389963] hub 5-0:1.0: USB hub found [ 0.390435] hub 5-0:1.0: 1 port detected [ 0.391103] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller [ 0.391765] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6 [ 0.392690] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600 [ 0.440100] ata2: SATA link down (SStatus 0 SControl 300) [ 0.448197] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.448978] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.449813] usb usb6: Product: BRCM OHCI controller [ 0.450381] usb usb6: Manufacturer: Linux 3.14-1.17-dm920 ohci_hcd [ 0.451095] usb usb6: SerialNumber: f0470600.ohci_v2 [ 0.451924] hub 6-0:1.0: USB hub found [ 0.452392] hub 6-0:1.0: 1 port detected [ 0.453094] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.453844] ehci-pci: EHCI PCI platform driver [ 0.454400] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.455120] ohci-pci: OHCI PCI platform driver [ 0.455741] usbcore: registered new interface driver usb-storage [ 0.456440] i2c /dev entries driver [ 0.456895] lirc_dev: IR Remote Control driver registered, major 250 [ 0.457948] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor d river [ 0.458927] usbcore: registered new interface driver btusb [ 0.459624] cpufreq_cpu0: failed to get cpu0 regulator: -19 [ 0.460442] brcmstb-cpufreq: probe of f03e257c.cpu-clk-div failed with error -17 [ 0.461370] sdhci: Secure Digital Host Controller Interface driver [ 0.462077] sdhci: Copyright(c) Pierre Ossman [ 0.462586] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.464337] mmc0: no vqmmc regulator found [ 0.464813] mmc0: no vmmc regulator found [ 0.495101] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using A DMA [ 0.497004] mmc1: no vqmmc regulator found [ 0.497483] mmc1: no vmmc regulator found [ 0.528095] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using A DMA [ 0.529038] hidraw: raw HID events driver (C) Jiri Kosina [ 0.529749] usbcore: registered new interface driver usbhid [ 0.530395] usbhid: USB HID core driver [ 0.532834] TCP: cubic registered [ 0.533835] NET: Registered protocol family 10 [ 0.534818] NET: Registered protocol family 17 [ 0.535572] Bluetooth: RFCOMM TTY layer initialized [ 0.536155] Bluetooth: RFCOMM socket layer initialized [ 0.536745] Bluetooth: RFCOMM ver 1.11 [ 0.537183] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.537792] Bluetooth: BNEP filters: protocol multicast [ 0.538401] Bluetooth: BNEP socket layer initialized [ 0.538972] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.539660] Bluetooth: HIDP socket layer initialized [ 0.540284] l2tp_core: L2TP core driver, V2.0 [ 0.540805] Key type dns_resolver registered [ 0.541374] Registering SWP/SWPB emulation handler [ 0.542204] regulator-dummy: disabling [ 0.542835] ALSA device list: [ 0.543199] No soundcards found. [ 0.543814] Waiting for root device /dev/mmcblk0p2... [ 0.595740] mmc1: BKOPS_EN bit is not set [ 0.602468] mmc1: new high speed MMC card at address 0001 [ 0.603292] mmcblk0: mmc1:0001 8GTF4R 7.28 GiB [ 0.603894] mmcblk0boot0: mmc1:0001 8GTF4R partition 1 4.00 MiB [ 0.604689] mmcblk0boot1: mmc1:0001 8GTF4R partition 2 4.00 MiB [ 0.605452] mmcblk0rpmb: mmc1:0001 8GTF4R partition 3 512 KiB [ 0.608603] mmcblk0: p1 p2 p3 [ 0.610061] mmcblk0boot1: unknown partition table [ 0.611071] mmcblk0boot0: unknown partition table [ 0.646078] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesyst em [ 0.646937] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 0.672928] EXT4-fs (mmcblk0p2): recovery complete [ 0.674159] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null) [ 0.675122] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 0.676309] devtmpfs: mounted [ 0.776118] random: systemd: uninitialized urandom read (16 bytes read, 51 bi ts of entropy available) [ 0.780585] systemd[1]: systemd 230 running in system mode. (-PAM -AUDIT -SEL INUX -IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT +GNUTLS +ACL + XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 0.782900] systemd[1]: Detected architecture arm. Welcome to opendreambox 2.5.0! [ 0.786581] systemd[1]: Set hostname to . [ 0.799651] random: systemd: uninitialized urandom read (16 bytes read, 54 bi ts of entropy available) [ 0.814762] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 57 bits of entropy available) [ 0.816311] systemd-fstab-generator[76]: Checking was requested for "rootfs", but it is not a device. [ 0.824478] random: systemd: uninitialized urandom read (16 bytes read, 57 bi ts of entropy available) [ 0.825650] random: systemd: uninitialized urandom read (16 bytes read, 57 bi ts of entropy available) [ 0.826989] random: systemd: uninitialized urandom read (16 bytes read, 57 bi ts of entropy available) [ 0.828195] random: systemd: uninitialized urandom read (16 bytes read, 57 bi ts of entropy available) [ 0.829489] random: systemd: uninitialized urandom read (16 bytes read, 57 bi ts of entropy available) [ 0.835257] random: systemd: uninitialized urandom read (16 bytes read, 60 bi ts of entropy available) [ 0.838949] random: systemd: uninitialized urandom read (16 bytes read, 60 bi ts of entropy available) [ 0.880048] systemd[1]: Configuration file /lib/systemd/system/CCcam_2.3.9.se rvice is marked executable. Please remove executable permission bits. Proceeding anyway. [ 0.898754] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 0.901191] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 0.903532] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 0.907343] systemd[1]: Starting Generate environment for enigma2... Starting Generate environment for enigma2... [ 0.910593] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 0.913201] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 0.916280] systemd[1]: Reached target Host and Network Name Lookups. [ OK ] Reached target Host and Network Name Lookups. [ 0.919378] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 0.922348] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 0.926418] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 0.930721] systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... [ 0.936851] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... [ 0.948908] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 0.954005] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 0.956938] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 0.958819] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 0.961380] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 0.966166] systemd[1]: Starting Journal Service... Starting Journal Service... [ 0.986876] systemd[1]: Set up automount data.automount. [ OK ] Set up automount data.automoun[ 0.988078] EXT4-fs (mmcblk0p2): re-mo unted. Opts: (null) t. [ 0.990397] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 0.996289] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 0.999810] systemd[1]: Started Setup Virtual Console. [ OK ] Started Setup Virtual Console. [ 1.003553] systemd[1]: Started Create list of required static device nodes f or the current kernel. [ OK ] Started Create list of required sta...ce nodes for the current kernel. [ 1.007657] systemd[1]: Started Remount Root and Kernel File Systems. [ OK ] Started Remount Root and Kernel File Systems. [ 1.010183] stb_core: module license 'Proprietary' taints kernel. [ 1.010888] Disabling lock debugging due to kernel taint [ 1.013593] systemd[1]: Started Generate environment for enigma2. [ OK ] Started Generate environment for enigma2. [ 1.023184] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices... [ 1.028697] systemd[1]: Starting Create Static Device Nodes in /dev... Starting Create Static Device Nodes in /dev... [ 1.046330] input: dreambox remote control (native) as /devices/virtual/input /input0 [ 1.047544] input: dreambox advanced remote control (native) as /devices/virt ual/input/input1 [ 1.086806] systemd[1]: Started Create Static Device Nodes in /dev. [ OK ] Started Create Static Device Nodes in /dev. [ 1.090601] systemd[1]: Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems (Pre). [ 1.093455] systemd[1]: Mounting /var/volatile... Mounting /var/volatile... [ 1.100691] systemd[1]: tmp.mount: Directory /tmp to mount over is not empty, mounting anyway. [ 1.103217] systemd[1]: Mounting /tmp... Mounting /tmp... [ 1.108366] systemd[1]: Starting udev Kernel Device Manager... Starting udev Kernel Device Manager... [ 1.113704] systemd[1]: Mounted /var/volatile. [ OK ] Mounted /var/volatile. [ 1.117206] systemd[1]: Mounted /tmp. [ OK ] Mounted /tmp. [ 1.119651] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. [ OK ] Started udev Coldplug all Devices. [ 1.249126] random: nonblocking pool is initialized [ 1.270867] bcm7439: xvd 20160630, vdc 20160630, rap 20160630, xpt 20160630, driver version 20200321-dm920 [ OK ] Started Load/Save Random Seed. [ 1.285269] systemd-journald[97]: Received request to flush runtime journal f rom PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. [ OK ] Found device /dev/ttyS0. Starting Update UTMP about System Boot/Shutdown... Starting RPC bind portmap service... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started RPC bind portmap service. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ 1.886370] 1:885287100 SMCB: controller reset timed out [ OK ] Found device /dev/sci0. [ 2.246293] register adapter [ 2.246873] register adapter [ 2.247443] register adapter [ 2.247950] register adapter [ 2.248532] register adapter [ 2.249037] fpga init [ 4.292644] fpga prog done [ 4.298024] using fpga version 47 [ 4.298791] fp: uart recv error 98 [ 4.299577] swd: status is 0, pls check [ 4.300019] swd: cannot init port [ 4.300411] ble module not found [ 4.300923] input: dreambox front panel as /devices/virtual/input/input2 [ 4.302205] HDMI: CEC start ... state is now 1 [ 4.302971] set input to 0 [ 4.303313] set fb to 2(-1) [ 4.305408] startvideomode '2160p50' read from /etc/videomode [ 4.306540] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8 _G8_B8) [ 4.341162] HDMI: now connected [ 4.369837] HDMI: CEC Physical Addr 1.0.0.0 set from EDID [ 4.370476] HDMI: EDID read ok [ 4.370833] HDMI: initial mode set! [ 4.371251] using 50.00Hz as MonitorRefreshRate [ 4.371774] SET FORMAT: display[0], format='2160p50' [ 4.372360] HDMI mode [ 4.372626] use EDID to detect colorspace [ 4.373096] preferred colorspace: Itu_R_BT_709 [ 4.373608] using 8bit output [ 4.502189] HDMI: CEC use logical address 3 [ 4.502701] HDMI: CEC init completed... state is now 3! [ 4.641973] HDMI: CEC send ok! [ 4.808861] VIDEO0: enable deinterlacer [ 4.809519] VIDEO0: set fallback framerate to 60000 [ 4.810109] VIDEO0: set progressive override mode to 1 [ 4.810703] VIDEO0: set streamtype! [ 4.811120] -> set MPEG2 [ 4.811465] -> sw rave disabled! [ 4.896350] VIDEO1: set fallback framerate to 60000 [ 4.896922] VIDEO1: set progressive override mode to 1 [ 4.897534] VIDEO1: set streamtype! [ 4.897943] -> set MPEG2 [ 4.898299] -> sw rave disabled! [ 4.934254] VIDEO2: set fallback framerate to 60000 [ 4.934821] VIDEO2: set progressive override mode to 1 [ 4.935431] VIDEO2: set streamtype! [ 4.935836] -> set MPEG2 [ 4.936189] -> sw rave disabled! [ 4.949386] set ac3 to downmix [ 4.949751] set wmapro to downmix [ 4.950167] set ac3plus to use_hdmi_caps [ 4.950628] set dtshd to force_dts [ 4.951030] set aac to downmix [ 4.951759] audio ch2: add stereo (background decoder) input to mixer DUMMY2 [ 4.952627] audio ch1: add stereo (hdmi-rx) input to mixer DUMMY [ 4.953613] DVB: registering new adapter (BCM7439) [ OK ] Found device /dev/dvb/adapter0/demux0. [ OK ] Found device /dev/dvb/adapter0/ca0. [ 5.116747] autodetecting NIMs... [ 5.122609] i2c: ret=-110 [ OK ] Found device /dev/dvb/adapter0/video0. Starting Dreambox Bootlogo... [ OK ] Started Dreambox Bootlogo. [ 5.139791] VIDEO0: set blank to 0 [ 5.140376] sync0 is off so we enable it [ 5.140832] sync0: allocated pcroffset 0 [ 5.141312] sync0: playback! [ 5.141662] VIDEO0: total delay: 0 (0 ms) [ 5.146937] VIDEO0: start decode [ 5.147509] VIDEO0: flush video decoder [ 5.147955] VIDEO0 got pts failed !!!! (ret 0) [ 5.173680] i2c: ret=-110 [ 5.174304] VIDEO0: first pts 0x0 [ 5.174705] VIDEO0: EOTF changed to SDR [ 5.175154] VIDEO0: framerate changed 3 [ 5.175601] VIDEO0: resolution changed (1280 720) [ 5.176144] VIDEO0: aspect changed 3 [ 5.176646] set current avs auto aspect to 16:9 [ 5.177197] set current avs auto aspect to 16:9 [ 5.177741] set sb to 3(1) [ 5.224656] i2c: ret=-110 [ 5.275654] i2c: ret=-110 [ 5.304759] VIDEO0: stop decode [ 5.305200] sync0 1fff no decoder left in sync handling so disable [ 5.305909] sync0: was last pcroffset0 user so free it [ 5.326665] i2c: ret=-110 [ 5.377652] i2c: ret=-110 [ 5.428650] i2c: ret=-110 [ 5.479649] i2c: ret=-110 [ 5.530647] i2c: ret=-110 [ 5.581646] i2c: ret=-110 [ 5.632654] i2c: ret=-110 [ 5.632960] Found: Slot 0, ID: 1f (by CA) [ 5.633436] Empty Slot 1 [ 5.633732] Initializing adapter 0 (BCM45308X-DVB-S2) [ 5.635019] bcm45208(0): chipid register is 45308 [ 5.638406] bcm45308(0): opening 8 sat channels (demods) [ 5.639040] (NULL device *): DVB: registering adapter 0 frontend 0 (BCM45208) ... [ 5.639984] bcm45308(0): InitAP [ 5.640508] Initializing adapter 1 (BCM45308X-DVB-S2) [ 5.641121] (NULL device *): DVB: registering adapter 0 frontend 1 (BCM45208) ... [ 5.642115] Initializing adapter 2 (BCM45308X-DVB-S2) [ 5.642731] (NULL device *): DVB: registering adapter 0 frontend 2 (BCM45208) ... [ 5.643770] Initializing adapter 3 (BCM45308X-DVB-S2) [ 5.644398] (NULL device *): DVB: registering adapter 0 frontend 3 (BCM45208) ... [ 5.645451] Initializing adapter 4 (BCM45308X-DVB-S2) [ 5.646060] (NULL device *): DVB: registering adapter 0 frontend 4 (BCM45208) ... [ 5.647156] Initializing adapter 5 (BCM45308X-DVB-S2) [ 5.647761] (NULL device *): DVB: registering adapter 0 frontend 5 (BCM45208) ... [ 5.651228] Initializing adapter 6 (BCM45308X-DVB-S2) [ 5.651838] (NULL device *): DVB: registering adapter 0 frontend 6 (BCM45208) ... [ 5.656416] Initializing adapter 7 (BCM45308X-DVB-S2) [ 5.657029] (NULL device *): DVB: registering adapter 0 frontend 7 (BCM45208) ... [ 5.659472] CI stopped... [ 5.661451] init ALSA! [ 5.663731] registered vtuner misc/vtuner0, minor 49 [ 5.665017] registered vtuner misc/vtuner1, minor 48 [ 5.666785] registered vtuner misc/vtuner2, minor 47 [ 5.668105] registered vtuner misc/vtuner3, minor 46 [ 5.668690] HDMI-RX: init [ 5.669806] HDMI-RX: no device attached [ 5.670329] HDMI-RX: video format change event [ 5.670844] HDMI-RX: hdmi packet status stopped [ 5.671381] HDMI-RX: hdmiInput0 Receiving DVI format [ 5.671972] HDMI-RX: hdmiInput0 Color Space change from '' to '' [ 5.672716] HDMI-RX: init done [ 5.673077] bcm_vce_init() [ 5.673409] bcm_vce_init() 0 [ 5.674996] CI stopped... [ OK ] Reached target Sound Card. [ 5.697958] vice0: allocate output buffers [ 5.706078] input: dreambox ir keyboard as /devices/virtual/input/input3 [ 5.707674] input: dreambox ir mouse as /devices/virtual/input/input4 [ 5.711564] ble init (0) [ 5.712280] input: dreambox remote control (bluetooth le) as /devices/virtual /input/input5 [ 5.725959] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ OK ] Started Load Kernel Modules. Mounting NFSD configuration filesystem... Starting Apply Kernel Variables... [ OK ] Mounted NFSD configuration filesystem. [ OK ] Started Apply Kernel Variables. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on busybox-telnetd.socket. [ OK ] Listening on dropbear.socket. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on dreamliveserver.socket. [ OK ] Listening on streamproxy.socket. [ OK ] Listening on tpmd.socket. [ OK ] Listening on vsftpd.socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Listening on dbttcd.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started System Logging Service. Starting Login Service... Starting dbttcd.service... Starting CCcam_2.3.9.service... Starting OsCam_11704.service... Starting tpmd.service... [ OK ] Started Kernel Logging Service. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started D-Bus System Message Bus. [ OK ] Started Avahi mDNS/DNS-SD Stack. Starting Connection service... Starting enigma2... [ OK ] Started Login Service. [ OK ] Started OsCam_11704.service. [ OK ] Started CCcam_2.3.9.service. [ OK ] Started Connection service. Starting Wait for network to be configured by ConnMan... [ OK ] Reached target Network. [ OK ] Started NFS status monitor for NFSv2/3 locking.. [ OK ] Started NFS Mount Daemon. Starting NFS server and services... [ OK ] Started tpmd.service. Starting Hostname Service... Starting WPA supplicant... [ 6.355110] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, pat ch: 1 [ 6.361342] f0b00000.ethernet: configuring instance for internal PHY [ 6.362238] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.376298] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery d irectory [ 6.380904] NFSD: starting 90-second grace period (net c07fd700) [ OK ] Started NFS server and services. [ OK ] Started WPA supplicant. [ OK ] Started Hostname Service. [ OK ] Started dbttcd.service. [ 8.001132] libphy: f0b00000.etherne:01 - Link is Up - 100/Full [ 8.001884] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started Wait for network to be configured by ConnMan. [ OK ] Reached target Network is Online. Starting Automounts filesystems on demand... [ OK ] Started Automounts filesystems on demand. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. opendreambox 2.5.0 dm920 ttyS0 dm920 login: [ 13.474669] bcm45308(0): Info Id: 6 Type: 0 Version: 11.2 [ 13.497099] bcm45308(0): FW Id: 11 Type: 0 Version 1.8 [ 13.497695] bcm45308(0): opening 2 wfe channels (input adcs) [ 13.498368] bcm45308(0): opening 2 dsq channels (DiSEqC) [ 13.498987] bcm45308(0): init lnb_ctrl 0 [ 13.499790] bcm45308(0): init lnb_ctrl 1 [ 13.554054] bcm45308(0): init MTSIF [ 14.117002] input0 set to A1 [ 14.117374] input1 set to A2 [ 14.117726] input2 set to A3 [ 14.118070] input3 set to A4 [ 14.118431] input4 set to A5 [ 14.118773] input5 set to A6 [ 14.119125] input6 set to A7 [ 14.119465] input7 set to A8 [ 14.119802] input8 set to B [ 14.120137] tsmux set tsports reg 00 to val 01 [ 14.121035] input9 set to B1 [ 14.121432] tsmux set tsports reg 01 to val 08 [ 14.122348] tsmux set cisource reg 06 to val 02 [ 14.123249] tsmux set ciclk reg 34 to val 00 [ 14.124178] tsmux set cisource reg 07 to val 05 [ 14.125155] tsmux set ciclk reg 34 to val 00 [ 14.340655] bcm45308(0): enabled diseqc and wfe 0 [ 14.352365] bcm45308(0): in normal mode now [ 14.352854] bcm45308(0): rf input 0 used [ 14.385171] bcm45308(0): disabled diseqc and wfe 0 [ 14.396861] bcm45308(0): sleeping now [ 14.421669] bcm45308(1): enabled diseqc and wfe 0 [ 14.433342] bcm45308(1): in normal mode now [ 14.433830] bcm45308(1): rf input 0 used [ 14.465638] bcm45308(1): disabled diseqc and wfe 0 [ 14.477312] bcm45308(1): sleeping now [ 14.501657] bcm45308(2): enabled diseqc and wfe 0 [ 14.514035] bcm45308(2): in normal mode now [ 14.514548] bcm45308(2): rf input 0 used [ 14.546420] bcm45308(2): disabled diseqc and wfe 0 [ 14.558164] bcm45308(2): sleeping now [ 14.583668] bcm45308(3): enabled diseqc and wfe 0 [ 14.595417] bcm45308(3): in normal mode now [ 14.595979] bcm45308(3): rf input 0 used [ 14.627765] bcm45308(3): disabled diseqc and wfe 0 [ 14.639656] bcm45308(3): sleeping now [ 14.663699] bcm45308(4): enabled diseqc and wfe 0 [ 14.675377] bcm45308(4): in normal mode now [ 14.675865] bcm45308(4): rf input 0 used [ 14.707841] bcm45308(4): disabled diseqc and wfe 0 [ 14.719553] bcm45308(4): sleeping now [ 14.743658] bcm45308(5): enabled diseqc and wfe 0 [ 14.755298] bcm45308(5): in normal mode now [ 14.755787] bcm45308(5): rf input 0 used [ 14.787712] bcm45308(5): disabled diseqc and wfe 0 [ 14.799467] bcm45308(5): sleeping now [ 14.823661] bcm45308(6): enabled diseqc and wfe 0 [ 14.835339] bcm45308(6): in normal mode now [ 14.835827] bcm45308(6): rf input 0 used [ 14.867662] bcm45308(6): disabled diseqc and wfe 0 [ 14.879397] bcm45308(6): sleeping now [ 14.903663] bcm45308(7): enabled diseqc and wfe 0 [ 14.915341] bcm45308(7): in normal mode now [ 14.915831] bcm45308(7): rf input 0 used [ 14.926537] HDMI: CEC device open ... state is 3, flushed 0 old messages from RX fifo [ 14.927640] HDMI: CEC set devtype to 0 [ 14.928111] HDMI: CEC start ... state is now 1 [ 14.928712] HDMI: CEC returned state 1 [ 14.929164] HDMI: CEC state now 801 [ 14.959593] bcm45308(7): disabled diseqc and wfe 0 [ 14.972322] bcm45308(7): sleeping now [ 14.991543] HDMI: CEC use logical address 3 [ 14.992049] HDMI: CEC init completed... state is now 3! [ 15.023445] bcmfb: creating surface with pixel format 0x07c68888 (BPXL_eA8_B8_G8_R8) [ 15.128355] HDMI: CEC send ok! [ 15.789580] 0 ms: [ 15.823176] 34 ms: 0 [ 15.827209] 4 ms: 0 [ 15.831659] 4 ms: 1 [ 16.070860] tsmux set cisource reg 06 to val 02 [ 16.072229] tsmux set cisource reg 07 to val 05 [ 16.116702] 285 ms: 1 [ 16.137363] 21 ms: 8 [ 16.144164] 7 ms: 9 [ 16.146175] 2 ms: 9 [ 16.152500] 6 ms: 9 [ 16.289939] 137 ms: 9 [ 16.310491] 20 ms: 13 [ 16.313501] 3 ms: 13 [ 16.314865] 1 ms: 13 [ 16.316194] 1 ms: 13 [ 16.345467] 29 ms: 13 [ 16.346936] 1 ms: 14 [ 16.397345] 50 ms: 14 [ 16.398844] 1 ms: 16 [ 16.416382] 17 ms: 16 [ 16.459900] 43 ms: 16 [ 16.461315] 1 ms: 17 [ 16.464954] 3 ms: 17 [ 16.466319] 1 ms: 17 [ 16.467581] 1 ms: 17 [ 16.470074] 2 ms: 17 [ 16.474544] 4 ms: 17 [ 16.483217] 9 ms: 17 [ 16.556418] change audioenc bitrate to 256000 bits/s [ 16.559010] vice0: change videoenc bitrate to 6000000 bits/s [ 16.559703] change audioenc bitrate to 128000 bits/s [ 16.562573] vice0: change gop length to 0ms [ 16.563071] vice0: allow new gop on new scene off [ 16.563646] vice0: change open gop to off [ 16.564169] vice0: change p-frames to 4 [ 16.564664] vice0: change b-frames to 2 [ 16.565133] vice0: change to 0 slices per pic [ 16.565737] vice0: change h264 profile to main [ 16.566302] vice0: change h264 level to 3.1 [ 16.656771] EXT4-fs (mmcblk0p3): recovery complete [ 16.658248] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 16.675909] 192 ms: 18 [ 16.677433] 1 ms: 23 [ 16.700327] 23 ms: 23 [ 16.707330] 7 ms: 23 [ 16.714707] 7 ms: 24 [ 16.718702] 4 ms: 24 [ 16.719760] 1 ms: 24 [ 16.721169] 2 ms: 24 [ 16.724932] 3 ms: 24 [ 16.725962] 0 ms: 24 [ 16.737245] 11 ms: 24 [ 16.767521] 30 ms: 25 [ 16.784183] 17 ms: 25 [ 16.785428] 1 ms: 26 [ 16.797881] 12 ms: 26 [ 16.798960] 0 ms: 26 [ 16.800220] 1 ms: 26 [ 16.802562] 2 ms: 26 [ 16.806066] 3 ms: 26 [ 16.812900] 6 ms: 26 [ 16.814115] 1 ms: 26 [ 16.936821] 122 ms: 26 [ 16.938544] 1 ms: 30 [ 17.001815] bcmfb: creating surface with pixel format 0x07c68888 (BPXL_eA8_B8_G8_R8) [ 17.057509] 119 ms: 30 [ 17.067278] 10 ms: 33 [ 17.070143] set input to 0 [ 17.070466] set fb to 2(-1) [ 17.070799] set current avs auto aspect to 16:9 [ 17.071427] set sb to 3(1) [ 17.072560] set ac3 to downmix [ 17.073554] set ac3plus to use_hdmi_caps [ 17.075946] using 50.00Hz as MonitorRefreshRate [ 17.076517] VIDEO1: shared window not available [ 17.077105] SET FORMAT: display[0], format='2160p50' [ 17.077691] HDMI mode [ 17.077960] use EDID to detect colorspace [ 17.078455] preferred colorspace: Itu_R_BT_709 [ 17.078977] using 8bit output [ 17.194792] VIDEO1: shared window not available [ 17.195377] set current avs auto aspect to 16:9 [ 17.195934] set sb to 3(1) [ 17.296105] using 50.00Hz as MonitorRefreshRate [ 17.296643] VIDEO1: shared window not available [ 17.297220] SET FORMAT: display[0], format='2160p50' [ 17.297808] HDMI mode [ 17.298101] use EDID to detect colorspace [ 17.298577] preferred colorspace: Itu_R_BT_709 [ 17.299109] using 8bit output [ 17.417554] VIDEO1: shared window not available [ 17.418137] set current avs auto aspect to 16:9 [ 17.418697] set sb to 3(1) [ 17.419584] 352 ms: 33 [ 17.423331] 4 ms: 43 [ 17.427134] 4 ms: 43 [ 17.530739] 103 ms: 43 [ 17.534993] 4 ms: 46 [ 18.757008] set current avs auto aspect to 16:9 [ 18.758357] set sb to 3(1) [ 18.758948] set current avs auto aspect to 16:9 [ 18.760668] set sb to 3(1) [ 18.764607] set current avs auto aspect to 16:9 [ 18.765283] set sb to 3(1) [ 18.768586] set current avs auto aspect to 16:9 [ 18.769261] set sb to 3(1) [ 18.769826] set current avs auto aspect to 16:9 [ 18.770497] set sb to 3(1) [ 18.771024] set current avs auto aspect to 16:9 [ 18.771696] set sb to 3(1) [ 18.775362] set current avs auto aspect to 16:9 [ 18.775941] set sb to 3(1) [ 18.776675] set current avs auto aspect to 16:9 [ 18.777355] set sb to 3(1) [ 18.777904] set current avs auto aspect to 16:9 [ 18.778569] set sb to 3(1) [ 18.779818] set current avs auto aspect to 16:9 [ 18.780448] set sb to 3(1) [ 18.780885] set current avs auto aspect to 16:9 [ 18.781504] set sb to 3(1) [ 18.783008] set current avs auto aspect to 16:9 [ 18.783675] set sb to 3(1) [ 18.784336] set current avs auto aspect to 16:9 [ 18.784899] set sb to 3(1) [ 18.785512] set current avs auto aspect to 16:9 [ 18.786062] set sb to 3(1) [ 18.810850] 1275 ms: 46 [ 18.814513] tsmux set ciclk reg 34 to val 00 [ 18.815955] tsmux set ciclk reg 34 to val 00 [ 18.823424] 12 ms: 79 [ 19.337382] 514 ms: 80 [ 19.538413] 201 ms: 94 [ 19.553420] set mute 0 1 [ 19.555127] 17 ms: 99 [ 19.556786] 1 ms: 100 [ 19.563000] 6 ms: 100 [ 19.632676] bcm45308(0): enabled diseqc and wfe 0 [ 19.644520] bcm45308(0): in normal mode now [ 19.645012] bcm45308(0): rf input 0 used [ 19.647998] input0 set to A1 [ 19.650691] tsmux set reg 40 to val 00 [ 19.651556] tsmux set reg 41 to val 00 [ 19.655556] start PCR0 on dmx 0 pid:641 index 3 [ 19.656651] start AUDIO0 on dmx 0 pid:6a5 index 1 [ 19.657230] audio ch0: xpt start [ 19.657617] audio ch0: reset GA threshold to 8ms [ 19.658179] sync0 is off so we enable it [ 19.658639] sync0: allocated pcroffset 0 [ 19.659118] sync0: demux-index 0 pcr pid 641 [ 19.659626] sync0: using 3 as pcr pidchannel [ 19.660205] audio ch0: MPEG [ 19.660537] audio ch0: streamtype set 0 [ 19.660986] audio ch0: streamtype_set: stop rave [ 19.661558] audio ch0: add stereo input to mixer DAC [ 19.662193] audio ch0: add stereo input to mixer SPDIF [ 19.662803] audio ch0: add stereo input to mixer MAI [ 19.663402] audio ch0: mai sample rate changed isr (48000) [ 19.664070] audio ch0: streamtype_set: restart rave [ 19.664786] audio ch0: decoder start [ 19.665226] audio ch0: video delay 0 (0 ms) [ 19.665717] VIDEO0: total delay: 0 (0 ms) [ 19.666863] VIDEO0: set streamtype! [ 19.667302] -> set H264 [ 19.667646] -> sw rave disabled! [ 19.668101] audio ch0 delay 18000 (200 ms) [ 19.668580] VIDEO0: total delay: 18000 (200 ms) [ 19.669242] start VIDEO0 on dmx 0 pid:641 index 3 [ 19.669822] VIDEO0: total delay: 18000 (200 ms) [ 19.673023] bcm45308(0): voltage(0) is now 13V [ 19.675492] VIDEO0: start decode [ 19.700647] HDMI: CEC returned state 3 [ 19.701133] HDMI: CEC state now 803 [ 19.855822] HDMI: CEC send ok! [ 19.964634] HDMI: CEC send ok! [ 20.042224] HDMI: CEC send ok! [ 20.114933] HDMI: CEC send ok! [ 20.251728] HDMI: CEC send ok! [ 20.319925] HDMI: CEC send ok! [ 20.397527] HDMI: CEC send ok! [ 21.138101] audio ch0: first pts 0x3887f546, stc 0x16b93a, pcr invalid [ 21.163983] audio ch0: lock [ 21.164349] audio ch0: sample rate changed isr (48000) [ 21.164974] audio ch0: tsm fail [ 21.165350] audio ch0: pts error 0 PTS 0x3887f546, STC 0x3887f468, type 0 [ 21.440971] audio ch0: status ready isr [ 22.155348] VIDEO0: first pts 0x388a3630 [ 22.155838] VIDEO0: resolution changed (1920 1080) [ 22.306107] VIDEO0: enable tsm [ 22.704735] VIDEO0: progressive changed (0)