[ 0.000000@0] Booting Linux on physical CPU 0x0 [ 0.000000@0] Linux version 4.9 (oe-user@oe-host) (gcc version 6.4.0 (GCC) ) #1 SMP PREEMPT Fri Aug 23 17:32:17 CEST 2019 [ 0.000000@0] Boot CPU: AArch64 Processor [410fd034] [ 0.000000@0] efi: Getting EFI parameters from FDT: [ 0.000000@0] efi: UEFI not found. [ 0.000000@0] OF: reserved mem: __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000007400000, len:36 MiB [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000005000000, size 36 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,secmon, compatible id shared-dma-pool [ 0.000000@0] OF: reserved mem: __reserved_mem_alloc_size, start:0x000000007f800000, end:0x0000000080000000, len:8 MiB [ 0.000000@0] Reserved memory: created CMA memory pool at 0x000000007f800000, size 8 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,meson-fb, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000053c00000, size 512 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,ion-dev, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x000000007d000000, size 40 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,di_cma, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created DMA memory pool at 0x000000007d000000, size 0 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,ppmgr, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000040800000, size 308 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,codec_mm_cma, compatible id shared-dma-pool [ 0.000000@0] OF: reserved mem: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000079000000, size 64 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,vdin0_cma, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000075000000, size 64 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,vdin1_cma, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000074000000, size 16 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,galcore, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000030800000, size 256 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,isp_cma, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x000000002d800000, size 48 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,adapt_cma, compatible id shared-dma-pool [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000029800000, size 64 MiB [ 0.000000@0] OF: reserved mem: initialized node linux,gdc_cma, compatible id shared-dma-pool [ 0.000000@0] cma: Reserved 8 MiB at 0x0000000029000000 [ 0.000000@0] On node 0 totalpages: 524032 [ 0.000000@0] DMA zone: 8188 pages used for memmap [ 0.000000@0] DMA zone: 0 pages reserved [ 0.000000@0] DMA zone: 524032 pages, LIFO batch:31 [ 0.000000@0] psci: probing for conduit method from DT. [ 0.000000@0] psci: PSCIv1.0 detected in firmware. [ 0.000000@0] psci: Using standard PSCI v0.2 function IDs [ 0.000000@0] psci: Trusted OS migration not required [ 0.000000@0] psci: SMC Calling Convention v1.1 [ 0.000000@0] percpu: Embedded 26 pages/cpu @ffffffc073eee000 s68888 r8192 d29416 u106496 [ 0.000000@0] pcpu-alloc: s68888 r8192 d29416 u106496 alloc=26*4096 [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [ 0.000000@0] Detected VIPT I-cache on CPU0 [ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515844 [ 0.000000@0] Kernel command line: logo=osd0,loaded,0x7f800000 vout=2160p50hz,enable hdmimode=2160p50hz fb_width=1280 fb_height=720 console=ttyS0,1000000 root=/dev/mmcblk0p7 rootwait rootfstype=ext4 no_console_suspend [ 0.000000@0] fb: osd0 [ 0.000000@0] fb: loaded [ 0.000000@0] fb: 0x7f800000 [ 0.000000@0] vout: 2160p50hz [ 0.000000@0] vout: enable: 1 [ 0.000000@0] vout: get hdmimode: 2160p50hz [ 0.000000@0] fb: logo_info.fb_width=1280 [ 0.000000@0] fb: logo_info.fb_height=720 [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000@0] Memory: 571704K/2096128K available (13692K kernel code, 1910K rwdata, 5700K rodata, 5312K init, 1487K bss, 66248K reserved, 1458176K cma-reserved) [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009de0000 ( 13696 KB) [ 0.000000@0] .rodata : 0xffffff8009de0000 - 0xffffff800a380000 ( 5760 KB) [ 0.000000@0] .init : 0xffffff800a380000 - 0xffffff800a8b0000 ( 5312 KB) [ 0.000000@0] .data : 0xffffff800a8b0000 - 0xffffff800aa8da00 ( 1911 KB) [ 0.000000@0] .bss : 0xffffff800aa8da00 - 0xffffff800ac019dc ( 1488 KB) [ 0.000000@0] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000@0] 0xffffffbf00004000 - 0xffffffbf02000000 ( 31 MB actual) [ 0.000000@0] memory : 0xffffffc000100000 - 0xffffffc080000000 ( 2047 MB) [ 0.000000@0] can't find symbol:arm_dma_alloc [ 0.000000@0] can't find symbol:__alloc_from_contiguous [ 0.000000@0] can't find symbol:cma_allocator_alloc [ 0.000000@0] 0, addr:ffffff8009a67c60 + 140, aml_cma_alloc_post_hook [ 0.000000@0] 1, addr:ffffff80095905f8 + 78, dma_alloc_from_contiguous [ 0.000000@0] 2, addr:ffffff8009215b18 + 2a8, cma_alloc [ 0.000000@0] 3, addr:ffffff8009206750 + 2f8, __kmalloc_track_caller [ 0.000000@0] 4, addr:ffffff80092038d8 + 2f8, __kmalloc [ 0.000000@0] 5, addr:ffffff8009203588 + 288, kmem_cache_alloc_trace [ 0.000000@0] 6, addr:ffffff8009203308 + 280, kmem_cache_alloc [ 0.000000@0] 7, addr:ffffff8009203280 + 88, __slab_alloc.isra.23.constprop.27 [ 0.000000@0] 8, addr:ffffff8009202f18 + 368, ___slab_alloc.constprop.28 [ 0.000000@0] 9, addr:ffffff8009200a78 + 568, new_slab [ 0.000000@0] 10, addr:ffffff80091f3f80 + 70, vmalloc [ 0.000000@0] 11, addr:ffffff80091f3e98 + 70, vzalloc [ 0.000000@0] 12, addr:ffffff80091f3950 + 298, __vmalloc_node_range [ 0.000000@0] 13, addr:ffffff80091d7ec8 + 110, kmalloc_order_trace [ 0.000000@0] 14, addr:ffffff80091d7d58 + 170, kmalloc_order [ 0.000000@0] 15, addr:ffffff80091b8080 + 168, __alloc_page_frag [ 0.000000@0] 16, addr:ffffff80091b8018 + 68, alloc_pages_exact [ 0.000000@0] 17, addr:ffffff80091b7fe8 + 30, get_zeroed_page [ 0.000000@0] 18, addr:ffffff80091b7f88 + 60, __get_free_pages [ 0.000000@0] 19, addr:ffffff80091b7140 + e48, __alloc_pages_nodemask [ 0.000000@0] 20, addr:ffffff800909c2c8 + 250, __dma_alloc [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000@0] Preemptible hierarchical RCU implementation. [ 0.000000@0] Build-time adjustment of leaf fanout to 64. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized [ 0.000000@0] g12a_aoclkc_init: register ao clk ok! [ 0.000000@0] Meson chip version = RevA (29:A - 40:0) [ 0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk [ 0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk [ 0.000000@0] meson_g12a_gpu_init: register meson gpu clk [ 0.000000@0] meson_g12a_media_init: register meson media clk [ 0.000000@0] meson_g12a_misc_init: register amlogic g12a misc clks [ 0.000000@0] meson_g12a_misc_init: done. [ 0.000000@0] g12a_clkc_init initialization complete [ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000043@0] meson_bc_timer: mclk->mux_reg =ffffff800800c190,mclk->reg =ffffff800800e194 [ 0.000717@0] Console: colour dummy device 80x25 [ 0.000737@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.000745@0] pid_max: default: 32768 minimum: 301 [ 0.000784@0] thread_stack_cache_init, vmap:ffffffc00017a0c0, bitmap:ffffffc000173000, cache page:1a0 [ 0.000795@0] thread_stack_cache_init, allocation vm area:ffffffc00013e740, addr:ffffff8020000000, size:20001000 [ 0.000801@0] cpu 0, vmap_stack:[ffffffc073ef8ab0-ffffffc073efcaa0] [ 0.000807@0] cpu 0, irq_stack: [ffffffc073eee060-ffffffc073ef2050] [ 0.000812@0] cpu 1, vmap_stack:[ffffffc073f12ab0-ffffffc073f16aa0] [ 0.000816@0] cpu 1, irq_stack: [ffffffc073f08060-ffffffc073f0c050] [ 0.000821@0] cpu 2, vmap_stack:[ffffffc073f2cab0-ffffffc073f30aa0] [ 0.000826@0] cpu 2, irq_stack: [ffffffc073f22060-ffffffc073f26050] [ 0.000831@0] cpu 3, vmap_stack:[ffffffc073f46ab0-ffffffc073f4aaa0] [ 0.000836@0] cpu 3, irq_stack: [ffffffc073f3c060-ffffffc073f40050] [ 0.000841@0] cpu 4, vmap_stack:[ffffffc073f60ab0-ffffffc073f64aa0] [ 0.000846@0] cpu 4, irq_stack: [ffffffc073f56060-ffffffc073f5a050] [ 0.000851@0] cpu 5, vmap_stack:[ffffffc073f7aab0-ffffffc073f7eaa0] [ 0.000857@0] cpu 5, irq_stack: [ffffffc073f70060-ffffffc073f74050] [ 0.000925@0] Security Framework initialized [ 0.000966@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000974@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.001569@0] ftrace: allocating 45089 entries in 177 pages [ 0.086090@0] sched-energy: Sched-energy-costs installed from DT [ 0.086107@0] CPU0: update cpu_capacity 631 [ 0.086121@0] ASID allocator initialised with 65536 entries [ 0.118385@0] EFI services will not be available. [ 0.165923@1] Detected VIPT I-cache on CPU1 [ 0.165976@1] CPU1: update cpu_capacity 631 [ 0.165978@1] CPU1: Booted secondary processor [410fd034] [ 0.198014@2] Detected VIPT I-cache on CPU2 [ 0.198059@2] CPU2: update cpu_capacity 920 [ 0.198061@2] CPU2: Booted secondary processor [410fd092] [ 0.230080@3] Detected VIPT I-cache on CPU3 [ 0.230103@3] CPU3: update cpu_capacity 920 [ 0.230105@3] CPU3: Booted secondary processor [410fd092] [ 0.262158@4] Detected VIPT I-cache on CPU4 [ 0.262181@4] CPU4: update cpu_capacity 920 [ 0.262184@4] CPU4: Booted secondary processor [410fd092] [ 0.294254@5] Detected VIPT I-cache on CPU5 [ 0.294277@5] CPU5: update cpu_capacity 920 [ 0.294279@5] CPU5: Booted secondary processor [410fd092] [ 0.294374@0] Brought up 6 CPUs [ 0.294423@0] SMP: Total of 6 processors activated. [ 0.294435@0] CPU features: detected feature: 32-bit EL0 Support [ 0.294570@0] CPU: All CPU(s) started at EL2 [ 0.294613@0] alternatives: patching kernel code [ 0.296013@0] VMAP:handle_vmap_fault address ffffff80200c4000 out of range [ 0.296039@0] VMAP:handle_vmap_fault PC is:ffffff8009242b74, copy_mount_options, LR is:ffffff8009242ae0 copy_mount_options [ 0.296049@0] VMAP:handle_vmap_fault task:44 kdevtmpfs, stack:ffffff80200c0000, ffffffc073efc920 [ 0.296060@0] CPU: 0 PID: 44 Comm: kdevtmpfs Not tainted 4.9 #1 [ 0.296067@0] Hardware name: Amlogic (DT) [ 0.296076@0] Call trace: [ 0.296090@0] [ffffffc073efc860+ 112][] dump_backtrace+0x0/0x248 [ 0.296102@0] [ffffffc073efc8d0+ 32][] show_stack+0x24/0x30 [ 0.296113@0] [ffffffc073efc8f0+ 48][] dump_stack+0xa4/0xd0 [ 0.296126@0] [ffffffc073efc920+ 64][] handle_vmap_fault+0x1e4/0x218 [ 0.296137@0] [ffffffc073efc960+ 0][] el1_da+0x14/0x148 [ 0.296147@0] [ffffff80200c3d30+ 80][] copy_mount_options+0xb8/0x1b0 [ 0.296157@0] [ffffff80200c3d80+ 64][] SyS_mount+0x70/0x108 [ 0.296170@0] [ffffff80200c3dc0+ 96][] devtmpfsd+0x6c/0x160 [ 0.296182@0] [ffffff80200c3e20+ 0][] kthread+0xe4/0xf8 [ 0.296192@0] [0000000000000000+ 0][] ret_from_fork+0x10/0x50 [ 0.296320@0] devtmpfs: initialized [ 0.318907@0] DMI not present or invalid. [ 0.319247@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.319266@0] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.350899@2] pinctrl core: initialized pinctrl subsystem [ 0.351625@2] NET: Registered protocol family 16 [ 0.352289@2] schedtune: init normalization constants... [ 0.352300@2] schedtune: CLUSTER[0-1] min_pwr: 0 max_pwr: 42 [ 0.352308@2] schedtune: CPU[0] min_pwr: 0 max_pwr: 279 [ 0.352315@2] schedtune: CPU[1] min_pwr: 0 max_pwr: 279 [ 0.352321@2] schedtune: CLUSTER[2-5] min_pwr: 0 max_pwr: 64 [ 0.352327@2] schedtune: CPU[2] min_pwr: 0 max_pwr: 759 [ 0.352333@2] schedtune: CPU[3] min_pwr: 0 max_pwr: 759 [ 0.352339@2] schedtune: CPU[4] min_pwr: 0 max_pwr: 759 [ 0.352345@2] schedtune: CPU[5] min_pwr: 0 max_pwr: 759 [ 0.352350@2] schedtune: SYSTEM min_pwr: 0 max_pwr: 3700 [ 0.352356@2] schedtune: using normalization constants mul: 459677581 sh1: 1 sh2: 11 [ 0.352361@2] schedtune: verify normalization constants... [ 0.352367@2] schedtune: max_pwr/2^0: 3700 => norm_pwr: 1024 [ 0.352372@2] schedtune: max_pwr/2^1: 1850 => norm_pwr: 512 [ 0.352377@2] schedtune: max_pwr/2^2: 925 => norm_pwr: 256 [ 0.352382@2] schedtune: max_pwr/2^3: 462 => norm_pwr: 127 [ 0.352388@2] schedtune: max_pwr/2^4: 231 => norm_pwr: 63 [ 0.352393@2] schedtune: max_pwr/2^5: 115 => norm_pwr: 31 [ 0.352398@2] schedtune: configured to support 5 boost groups [ 0.362244@2] cpuidle: using governor menu [ 0.362290@2] register canvas platform driver [ 0.362312@2] register rdma platform driver [ 0.362334@2] aml_vdac_init: module init [ 0.362869@2] vdso: 2 pages (1 code @ ffffff8009de7000, 1 data @ ffffff800a8b5000) [ 0.362883@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.363477@0] DMA: preallocated 256 KiB pool for atomic allocations [ 0.363719@0] clkmsr: clkmsr: driver init [ 0.363727@0] codec_mm_module_init [ 0.363761@0] media_configs_system_init [ 0.364230@0] pstore: using zlib compression [ 0.365023@0] console [pstore-1] enabled [ 0.365284@0] pstore: Registered ramoops as persistent store backend [ 0.365296@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0 [ 0.367620@0] aml_iomap: amlogic iomap probe done [ 0.368063@0] vpu: driver version: v20180925(8-g12b) [ 0.368077@0] vpu: load vpu_clk: 666666667Hz(7) [ 0.368286@0] vpu: clktree_init [ 0.368343@0] vpu: vpu_probe OK [ 0.373375@0] clkmsr: msr_clk_reg0=ffffff80081c0004,msr_clk_reg2=ffffff80081c200c [ 0.373397@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0 [ 0.379432@0] aml_vdac_probe:probe start.cpu_id:6,name:meson-g12ab-vdac [ 0.379631@0] aml_vdac_probe: ok [ 0.379819@0] canvas_probe reg=00000000ff638000,size=2000 [ 0.379844@0] canvas maped reg_base =ffffff80081c4000 [ 0.386412@2] rdma_probe,ver:0, len:8 [ 0.386586@2] rdma_register, rdma_table_addr ffffff80081e5000 rdma_table_addr_phy 29040000 reg_buf ffffffc026598000 [ 0.386596@2] rdma_register success, handle 1 table_size 32768 [ 0.386604@2] set_rdma_handle video rdma handle = 1. [ 0.387501@2] aml_snd_reg_map[0], reg:ff640000, size:2000 [ 0.387520@2] aml_snd_reg_map[1], reg:ff642000, size:2000 [ 0.387536@2] aml_snd_reg_map[2], reg:ff64a000, size:2000 [ 0.387552@2] aml_snd_reg_map[3], reg:ff656000, size:1800 [ 0.387570@2] aml_snd_reg_map[4], reg:ffd01000, size:1000 [ 0.387578@2] amlogic auge_snd_iomap probe done [ 0.389478@2] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.389541@2] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.389549@2] codec_mm_probe ok [ 0.535411@2] vgaarb: loaded [ 0.535598@2] SCSI subsystem initialized [ 0.535743@2] usbcore: registered new interface driver usbfs [ 0.535783@2] usbcore: registered new interface driver hub [ 0.535860@2] usbcore: registered new device driver usb [ 0.535923@2] Linux video capture interface: v2.00 [ 0.535963@2] pps_core: LinuxPPS API ver. 1 registered [ 0.535970@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.535985@2] PTP clock support registered [ 0.536187@2] dmi: Firmware registration failed. [ 0.536386@2] secmon: reserve_mem_size:0x2300000 [ 0.536458@2] secmon secmon: assigned reserved memory node linux,secmon [ 0.536469@2] secmon: clear_range:5100000 1e00000 [ 0.537160@2] secmon: get page:ffffffbf00140000, 5000 [ 0.537293@2] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000 [ 0.537301@2] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000 [ 0.537659@2] fb: osd_init_module [ 0.537929@2] fb: viu vsync irq: 39 [ 0.537949@2] fb: viu2 vsync irq: 48 [ 0.538043@2] 0x000000d8:Y=d8,U=0,V=0 [ 0.538052@2] 0x000000d9:Y=d9,U=0,V=0 [ 0.538059@2] 0x000000da:Y=da,U=0,V=0 [ 0.538067@2] 0x000000db:Y=db,U=0,V=0 [ 0.538223@2] fb: osd_rdma_init: rdma_table p=0x29048000,op=0x29048000 , v=0xffffff80082d1000 [ 0.538251@2] rdma_register, rdma_table_addr ffffff80082d3000 rdma_table_addr_phy 29049000 reg_buf ffffffc026523000 [ 0.538260@2] rdma_register success, handle 2 table_size 4096 [ 0.538267@2] fb: osd_rdma_init:osd rdma handle = 2. [ 0.538283@2] fb: mem_size: 0x800000 [ 0.538289@2] fb: mem_size: 0x1800000 [ 0.538296@2] fb: mem_size: 0x100000 [ 0.538303@2] fb: mem_size: 0x100000 [ 0.538309@2] fb: mem_size: 0x800000 [ 0.538363@2] meson-fb meson-fb: assigned reserved memory node linux,meson-fb [ 0.538372@2] fb: reserved memory base:0x000000007f800000, size:800000 [ 0.538575@2] vout: error: invalid vinfo1. current vmode is not supported [ 0.538586@2] fb: init fbdev bpp is:32 [ 0.539468@2] fb: set osd0 reverse as NONE [ 0.546446@2] fb: osd probe OK [ 0.546987@2] hdmitx: system: amhdmitx_probe start [ 0.546996@2] hdmitx: system: Ver: 20181019 [ 0.547019@2] hdmitx: system: hdmitx_device.chip_type : 11 [ 0.547051@2] hdmitx: system: not find product desc [ 0.547059@2] hdmitx: system: not find match pwr-ctl [ 0.547093@2] hdmitx: system: not find drm_amhdmitx [ 0.547117@2] hdmitx: system: hpd irq = 32 [ 0.547222@2] hdmitx: system: hdcp22_tx_skp failed to probe [ 0.547232@2] hdmitx: system: hdcp22_tx_esm failed to probe [ 0.547522@2] vout: vout1: register server: hdmitx_vout_server [ 0.547532@2] vout: vout2: register server: hdmitx_vout2_server [ 0.547896@2] hdmitx: hdmitx20: Mapped PHY: 0xffd00000 [ 0.547912@2] hdmitx: hdmitx20: Mapped PHY: 0xff634400 [ 0.547926@2] hdmitx: hdmitx20: Mapped PHY: 0xff900000 [ 0.547946@2] hdmitx: hdmitx20: Mapped PHY: 0xff800000 [ 0.547956@2] hdmitx: hdmitx20: Mapped PHY: 0xff63c000 [ 0.547965@2] hdmitx: hdmitx20: Mapped PHY: 0xffd00000 [ 0.547974@2] hdmitx: hdmitx20: Mapped PHY: 0xff608000 [ 0.547983@2] hdmitx: hdmitx20: Mapped PHY: 0xff600000 [ 0.547994@2] hdmitx: hdmitx20: Mapped PHY: 0xffe01000 [ 0.548007@2] hdmitx: hw: alread display in uboot 0x60 [ 0.548033@2] hdmitx: hw: avmute set to 1 [ 0.548042@2] hdmitx: system: fmt_attr 444,8bit [ 0.548132@2] hdmitx: system: amhdmitx_probe end [ 0.548670@2] vout: create vout attribute OK [ 0.548796@2] vout: vout_fops_create OK [ 0.548805@2] vout: vout1: register server: nulldisp_vout_server [ 0.548821@2] hdmitx: hdmitx_set_current_vmode[3490] [ 0.548829@2] hdmitx: system: recalc before 2160p50hz 50 1 [ 0.548839@2] hdmitx: system: recalc after 2160p50hz 50 1 [ 0.548846@2] hdmitx: alread display in uboot [ 0.548853@2] vout: init mode 2160p50hz set ok [ 0.548924@2] vout: aml_tvout_mode_monitor [ 0.548936@2] vout: aml_vout_probe OK [ 0.549404@2] chip type:0x29 [ 0.549734@2] Advanced Linux Sound Architecture Driver Initialized. [ 0.550085@2] Bluetooth: Core ver 2.22 [ 0.550117@2] NET: Registered protocol family 31 [ 0.550125@2] Bluetooth: HCI device and connection manager initialized [ 0.550138@2] Bluetooth: HCI socket layer initialized [ 0.550149@2] Bluetooth: L2CAP socket layer initialized [ 0.550177@2] Bluetooth: SCO socket layer initialized [ 0.551276@2] clocksource: Switched to clocksource arch_sys_counter [ 0.555211@0] hdmitx: system: irq 4 [ 0.575232@0] hdmitx: system: irq 2 [ 0.600429@2] VFS: Disk quotas dquot_6.6.0 [ 0.600484@2] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.607219@2] dtv_dmd:[amldtvdemod..]aml_dtvdemod_init. [ 0.607230@2] jtag: module init [ 0.607466@2] NET: Registered protocol family 2 [ 0.607863@2] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.607961@2] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 0.608077@2] TCP: Hash tables configured (established 16384 bind 16384) [ 0.608133@2] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 0.608160@2] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 0.608282@2] NET: Registered protocol family 1 [ 0.608612@2] RPC: Registered named UNIX socket transport module. [ 0.608619@2] RPC: Registered udp transport module. [ 0.608625@2] RPC: Registered tcp transport module. [ 0.608631@2] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.608640@2] PCI: CLS 0 bytes, default 64 [ 0.609992@2] wifi: power_on_pin_OD = 0; [ 0.610005@2] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2 [ 0.610090@2] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok [ 0.610107@2] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok [ 0.610117@2] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup [ 0.610125@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem 1.579.77.41.9 [ 0.610432@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem prealloc ok [ 0.610442@2] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=472 [ 0.610451@2] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1 [ 0.610459@2] aml_wifi wifi: [wifi_dev_probe] power_on_pin=471 [ 0.610467@2] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0 [ 0.610606@2] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt [ 0.610671@2] aml_wifi wifi: [wifi_setup_dt] irq num is:(69) [ 0.610681@2] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(472) [ 0.610698@2] aml_wifi wifi: [wifi_setup_dt] power_on_pin(471) [ 0.611546@2] perf_event: read sys_cpu_status0_offset failed, ret = -22 [ 0.611564@2] armv8-pmu: probe of arm_pmu failed with error 1 [ 0.613722@2] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 0.620767@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.620943@2] exFAT: Version 1.2.9 [ 0.621580@2] Registering sdcardfs 0.1 [ 0.622362@2] NFS: Registering the id_resolver key type [ 0.622386@2] Key type id_resolver registered [ 0.622394@2] Key type id_legacy registered [ 0.622408@2] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.623031@2] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.623232@2] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.623610@2] fuse init (API version 7.26) [ 0.626678@2] NET: Registered protocol family 38 [ 0.626692@2] Key type asymmetric registered [ 0.626701@2] Asymmetric key parser 'x509' registered [ 0.626832@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 0.626842@2] io scheduler noop registered (default) [ 0.626850@2] io scheduler deadline registered [ 0.626968@2] io scheduler cfq registered [ 0.633429@3] random: fast init done [ 0.633468@3] random: crng init done [ 0.633675@2] Unable to detect cache hierarchy for CPU 0 [ 0.637771@2] loop: module loaded [ 0.638241@2] zram: Added device: zram0 [ 0.638432@2] mtdoops: mtd device (mtddev=name/number) must be supplied [ 0.639019@2] libphy: Fixed MDIO Bus: probed [ 0.639145@2] tun: Universal TUN/TAP device driver, 1.6 [ 0.639153@2] tun: (C) 1999-2004 Max Krasnyansky [ 0.639786@2] REG0:Addr = ffffff80084c4540 [ 0.640084@2] meson6-dwmac ff3f0000.ethernet: no reset control found [ 0.640095@2] stmmac - user ID: 0x11, Synopsys ID: 0x37 [ 0.640103@2] Ring mode enabled [ 0.640111@2] DMA HW capability register supported [ 0.640118@2] Normal descriptors [ 0.640126@2] RX Checksum Offload Engine supported [ 0.640133@2] COE Type 2 [ 0.640140@2] TX Checksum insertion supported [ 0.640146@2] Wake-Up On Lan supported [ 0.640183@2] Enable RX Mitigation via HW Watchdog Timer [ 0.647461@2] libphy: stmmac: probed [ 0.647472@2] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active [ 0.647481@2] eth%d: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07) [ 0.648374@2] PPP generic driver version 2.4.2 [ 0.648500@2] PPP BSD Compression module registered [ 0.648509@2] PPP Deflate Compression module registered [ 0.648530@2] PPP MPPE Compression module registered [ 0.648539@2] NET: Registered protocol family 24 [ 0.648601@2] usbcore: registered new interface driver asix [ 0.648658@2] usbcore: registered new interface driver ax88179_178a [ 0.648694@2] usbcore: registered new interface driver cdc_ether [ 0.648727@2] usbcore: registered new interface driver net1080 [ 0.648761@2] usbcore: registered new interface driver cdc_subset [ 0.648798@2] usbcore: registered new interface driver zaurus [ 0.648842@2] usbcore: registered new interface driver cdc_ncm [ 0.649541@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.649550@2] ehci-pci: EHCI PCI platform driver [ 0.649588@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.649606@2] ohci-pci: OHCI PCI platform driver [ 0.649961@2] usbcore: registered new interface driver cdc_acm [ 0.649969@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 0.650015@2] usbcore: registered new interface driver usb-storage [ 0.650246@2] mousedev: PS/2 mouse device common for all mice [ 0.650413@2] usbcore: registered new interface driver xpad [ 0.650516@2] i2c /dev entries driver [ 0.650667@2] IR NEC protocol handler initialized [ 0.650674@2] IR RC5(x/sz) protocol handler initialized [ 0.650682@2] IR RC6 protocol handler initialized [ 0.650689@2] IR JVC protocol handler initialized [ 0.650696@2] IR Sony protocol handler initialized [ 0.650703@2] IR SANYO protocol handler initialized [ 0.650710@2] IR Sharp protocol handler initialized [ 0.650717@2] IR MCE Keyboard/mouse protocol handler initialized [ 0.650724@2] IR XMP protocol handler initialized [ 0.650772@2] usbcore: registered new interface driver uvcvideo [ 0.650780@2] USB Video Class driver (1.1.1) [ 0.650824@2] usbcore: registered new interface driver cx231xx [ 0.650833@2] md: linear personality registered for level -1 [ 0.651095@2] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 0.651106@2] Bluetooth: HCI UART driver ver 2.3 [ 0.651115@2] Bluetooth: HCI UART protocol H4 registered [ 0.652014@2] ledtrig-cpu: registered to indicate activity on CPUs [ 0.652328@2] hidraw: raw HID events driver (C) Jiri Kosina [ 0.652497@2] usbcore: registered new interface driver usbhid [ 0.652505@2] usbhid: USB HID core driver [ 0.652606@2] ashmem: initialized [ 0.653014@2] value of voltage_tolerance 0 [ 0.653742@2] cpu cpu0: meson_cpufreq_init: CPU 0 initialized [ 0.654726@2] value of voltage_tolerance 0 [ 0.655475@2] cpu cpu2: meson_cpufreq_init: CPU 2 initialized [ 0.655505@2] cpufreq: cpufreq_online: CPU2: Running at unlisted freq: 24000 KHz [ 0.657429@2] cpufreq: cpufreq_online: CPU2: Unlisted initial frequency changed to: 100000 KHz [ 0.659286@2] meson_cpufreq_probe: Registered platform drive [ 0.659383@2] ff803000.serial: clock gate not found [ 0.659418@2] meson_uart ff803000.serial: ==uart0 reg addr = ffffff80084c8000 [ 0.659448@2] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 22, base_baud = 1500000) is a meson_uart [ 0.659461@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 1000000 [ 0.940012@2] console [ttyS0] enabled [ 0.940657@2] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff80084ca000 [ 0.941252@2] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 31, base_baud = 1500000) is a meson_uart [ 0.942897@2] amlogic-new-usb2-v2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff80084cc000 [ 0.943723@2] amlogic-new-usb3-v2 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff80084e9080 [ 0.946549@2] meson-remote: Driver init [ 0.946642@2] meson-remote: remote_probe [ 0.946802@2] meson-remote ff808040.rc: protocol = 0x1 [ 0.947399@2] meson-remote ff808040.rc: don't find the node [ 0.948147@2] meson-remote ff808040.rc: led_blink = 0 [ 0.948727@2] meson-remote ff808040.rc: don't find the node [ 0.949526@2] meson-remote ff808040.rc: led_blink_frq = 100 [ 0.950184@2] meson-remote ff808040.rc: platform_data irq =30 [ 0.950846@2] meson-remote ff808040.rc: custom_number = 4 [ 0.951473@2] meson-remote ff808040.rc: ptable->map_size = 41 [ 0.952117@2] meson-remote ff808040.rc: ptable->custom_name = dreambox-rc32 [ 0.952917@2] meson-remote ff808040.rc: ptable->custom_code = 0xcd32 [ 0.953647@2] meson-remote ff808040.rc: ptable->release_delay = 80 [ 0.954366@2] meson-remote ff808040.rc: ptable->map_size = 41 [ 0.955017@2] meson-remote ff808040.rc: ptable->custom_name = dreambox-rc33 [ 0.955823@2] meson-remote ff808040.rc: ptable->custom_code = 0xcc33 [ 0.956547@2] meson-remote ff808040.rc: ptable->release_delay = 80 [ 0.957267@2] meson-remote ff808040.rc: ptable->map_size = 41 [ 0.957917@2] meson-remote ff808040.rc: ptable->custom_name = dreambox-rc34 [ 0.958717@2] meson-remote ff808040.rc: ptable->custom_code = 0xcb34 [ 0.959452@2] meson-remote ff808040.rc: ptable->release_delay = 80 [ 0.960167@2] meson-remote ff808040.rc: ptable->map_size = 41 [ 0.960817@2] meson-remote ff808040.rc: ptable->custom_name = dreambox-rc35 [ 0.961617@2] meson-remote ff808040.rc: ptable->custom_code = 0xca35 [ 0.962347@2] meson-remote ff808040.rc: ptable->release_delay = 80 [ 0.963059@2] meson-remote ff808040.rc: default protocol = 0x1 and id = 0 [ 0.963843@2] meson-remote ff808040.rc: reg=0x0, val=0x1f40190 [ 0.964507@2] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8 [ 0.965177@2] meson-remote ff808040.rc: reg=0x8, val=0x960050 [ 0.965836@2] meson-remote ff808040.rc: reg=0xc, val=0x480028 [ 0.966496@2] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013 [ 0.967187@2] meson-remote ff808040.rc: reg=0x18, val=0x8616800 [ 0.967871@2] meson-remote ff808040.rc: reg=0x1c, val=0x9f00 [ 0.968516@2] meson-remote ff808040.rc: reg=0x20, val=0x0 [ 0.969136@2] meson-remote ff808040.rc: reg=0x24, val=0x0 [ 0.969756@2] meson-remote ff808040.rc: reg=0x28, val=0x0 [ 0.970545@2] input: aml_keypad as /devices/platform/ff808040.rc/input/input0 [ 0.971391@2] meson-remote: IR XMP protocol handler initialized [ 0.972948@2] ion_dev soc:ion_dev: assigned reserved memory node linux,ion-dev [ 0.973354@2] ge2d: ge2d_init_module [ 0.973640@2] ge2d: ge2d_dev major:237 [ 0.974075@2] ge2d: clock source clk_ge2d_gate ffffffc025ae7a00 [ 0.974671@2] ge2d: clock clk_ge2d source ffffffc025ae7a80 [ 0.975304@2] ge2d: clock source clk_vapb_0 ffffffc025ae7b00 [ 0.975935@2] ge2d: ge2d init clock is 500000000 HZ, VPU clock is 666666656 HZ [ 0.976821@2] ge2d: ge2d clock is 499 MHZ [ 0.977231@2] ge2d: find address resource [ 0.977687@2] ge2d: map io source 0x00000000ff940000,size=65536 to 0xffffff8008690000 [ 0.978585@2] ge2d: ge2d: pdev=ffffffc026530800, irq=38, clk=ffffffc025ae7a00 [ 0.979431@2] ge2d: ge2d start monitor [ 0.979869@3] ge2d: ge2d workqueue monitor start [ 0.980070@2] amvideom vsync irq: 39 [ 0.980332@2] hdmitx: hdcp: hdmitx_hdcp_init [ 0.980554@2] vout: vout2: create vout2 attribute OK [ 0.980604@2] vout: vout2: vout2_fops_create OK [ 0.980606@2] vout: vout2: register server: nulldisp_vout2_server [ 0.980611@2] vout: vout2: init mode null set ok [ 0.980678@2] vout: vout2: clktree_init [ 0.980722@2] vout: vout2: aml_vout2_probe OK [ 0.980769@2] DI: di_module_init ok. [ 0.980772@2] DI: di_module_init: major 511 [ 0.980931@2] deinterlace deinterlace: assigned reserved memory node linux,di_cma [ 0.980934@2] DI: CMA size 0x2800000. [ 0.980943@2] pre_irq:63 [ 0.980950@2] post_irq:64 [ 0.980952@2] DI: di_probe allocate rdma channel 0. [ 0.980955@2] di_get_vpu_clkb: get clk vpu error. [ 0.980957@2] DI: vpu clkb <334000000, 667000000> [ 0.980976@2] DI:enable vpu clkb. [ 0.980986@2] 0x000000dc:Y=dc,U=0,V=0 [ 0.980987@2] 0x000000dd:Y=dd,U=0,V=0 [ 0.980988@2] 0x000000de:Y=de,U=0,V=0 [ 0.980990@2] 0x000000df:Y=df,U=0,V=0 [ 0.980991@2] 0x000000e0:Y=e0,U=0,V=0 [ 0.980992@2] 0x000000e1:Y=e1,U=0,V=0 [ 0.980993@2] 0x000000e2:Y=e2,U=0,V=0 [ 0.980994@2] 0x000000e3:Y=e3,U=0,V=0 [ 0.980995@2] 0x000000f0:Y=f0,U=0,V=0 [ 0.980996@2] 0x000000f1:Y=f1,U=0,V=0 [ 0.981001@2] 0x000000f2:Y=f2,U=0,V=0 [ 0.981002@2] 0x000000f3:Y=f3,U=0,V=0 [ 0.981003@2] 0x000000f4:Y=f4,U=0,V=0 [ 0.981004@2] 0x000000f5:Y=f5,U=0,V=0 [ 0.981005@2] 0x000000f6:Y=f6,U=0,V=0 [ 0.981006@2] 0x000000f7:Y=f7,U=0,V=0 [ 0.981010@2] 0x000000f8:Y=f8,U=0,V=0 [ 0.981011@2] 0x000000f9:Y=f9,U=0,V=0 [ 0.981013@2] 0x000000fa:Y=fa,U=0,V=0 [ 0.981014@2] 0x000000fb:Y=fb,U=0,V=0 [ 0.981015@2] 0x000000fc:Y=fc,U=0,V=0 [ 0.981016@2] 0x000000fd:Y=fd,U=0,V=0 [ 0.981018@2] 0x000000fe:Y=fe,U=0,V=0 [ 0.981020@2] 0x000000ff:Y=ff,U=0,V=0 [ 0.981021@2] 0x0000003a:Y=3a,U=0,V=0 [ 0.981022@2] DI: support multi decoding 254~255~58. [ 0.981116@2] DI: di_probe:Di use HRTIMER [ 0.981168@2] di_probe:ok [ 0.981201@2] vdin_drv_init: major 510 [ 0.981878@2] rdma_register, rdma_table_addr ffffff80084fd000 rdma_table_addr_phy 2904a000 reg_buf ffffffc025b0b600 [ 0.981879@2] rdma_register success, handle 3 table_size 512 [ 0.981881@2] vdin_drv_probe:vdin.0 rdma hanld 3. [ 0.981964@2] vdin vdin0: assigned reserved memory node linux,vdin0_cma [ 0.981965@2] [ 0.981965@2] vdin memory resource done. [ 0.981968@2] vdin0 cma_mem_size = 64 MB [ 0.981971@2] vdin0 irq: 36 rdma irq: 2 [ 0.981973@2] no afbce mode found, use normal mode [ 0.981974@2] no urgent_en found [ 0.981987@2] get fclk_div5 err [ 0.981989@2] vdin_drv_probe: vdin cannot get msr clk !!! [ 0.982001@2] vdin_drv_probe: driver initialized ok [ 0.982034@2] rdma_register, rdma_table_addr ffffff8008622000 rdma_table_addr_phy 2904b000 reg_buf ffffffc025b0b800 [ 0.982036@2] rdma_register success, handle 4 table_size 512 [ 0.982037@2] vdin_drv_probe:vdin.1 rdma hanld 4. [ 0.982120@2] vdin vdin1: assigned reserved memory node linux,vdin1_cma [ 0.982122@2] [ 0.982122@2] vdin memory resource done. [ 0.982124@2] vdin1 cma_mem_size = 64 MB [ 0.982125@2] vdin1 irq: 37 rdma irq: 4 [ 0.982127@2] no afbce mode found, use normal mode [ 0.982129@2] no urgent_en found [ 0.982138@2] get fclk_div5 err [ 0.982140@2] vdin_drv_probe: vdin cannot get msr clk !!! [ 0.982145@2] vdin_debugfs_init only support debug vdin0 1 [ 0.982146@2] vdin_drv_probe: driver initialized ok [ 0.982191@2] vdin_drv_init: vdin driver init done [ 0.982193@2] [viuin..]viuin_init_module viuin module init [ 0.982328@2] [viuin..]viuin_probe probe ok. [ 0.982564@2] [RX]-hdmirx: hdmirx_init. [ 0.982566@2] ESM HLD: Initializing... [ 0.982617@2] tvin_afe: tvafe_drv_init: major 508 [ 0.982753@2] tvin_afe: tvafe_drv_init. [ 0.982842@2] tvafe_vbi: vbi: vbi_init. [ 0.982942@2] amlvid:info: amlvideo_init called [ 0.982942@2] amlvid:info: amlvideo_create_instance called [ 0.982946@2] amlvid:info: v4l2_dev.name=:amlvideo-000 [ 0.983009@2] amlvideo-000: V4L2 device registered as video10 [ 0.983095@2] PPMGRDRV: warn: ppmgr module init func called [ 0.983173@2] PPMGRDRV: err: ppmgr_driver_probe called [ 0.983189@2] Reserved memory: failed to init DMA memory pool at 0x000000007d000000, size 0 MiB [ 0.983192@2] PPMGRDRV: info: ppmgr_dev major:506 [ 0.983521@2] ionvideo-000: V4L2 device registered as video13 [ 0.983577@2] ionvideo-001: V4L2 device registered as video14 [ 0.983631@2] ionvideo-002: V4L2 device registered as video15 [ 0.983686@2] ionvideo-003: V4L2 device registered as video16 [ 0.983738@2] ionvideo-004: V4L2 device registered as video17 [ 0.983788@2] ionvideo-005: V4L2 device registered as video18 [ 0.983841@2] ionvideo-006: V4L2 device registered as video19 [ 0.983894@2] ionvideo-007: V4L2 device registered as video20 [ 0.983951@2] ionvideo-008: V4L2 device registered as video21 [ 0.983953@2] ionvid: info: Video Technology Magazine Ion Video [ 0.983955@2] ionvid: info: Capture Board ver 1.0 successfully loaded [ 0.984066@2] aml_vecm_init:module init [ 0.984158@2] [ 0.984158@2] VECM probe start [ 0.984283@2] vlock_status_init vlock_en:0 [ 0.984295@2] Can't find wb_sel. [ 0.984297@2] hdr:Can't find cfg_en_osd_100. [ 0.984298@2] Can't find tx_op_color_primary. [ 0.984301@2] amlogic, vecm [ 0.984301@2] vlock dt support: 1 [ 0.984302@2] vlock dt new_fsm: 0 [ 0.984303@2] vlock dt hwver: 0 [ 0.984304@2] vlock dt phlock_en: 0 [ 0.984306@2] Can't find vlock_en. [ 0.984307@2] Can't find vlock_mode. [ 0.984308@2] Can't find vlock_pll_m_limit. [ 0.984309@2] Can't find vlock_line_limit. [ 0.984317@2] param_config vlock_en:0 [ 0.984329@2] aml_vecm_probe: ok [ 0.984351@2] amdolby_vision_init:module init [ 0.984466@2] [ 0.984466@2] amdolby_vision probe start & ver: 20181009 [ 0.984469@2] [ 0.984469@2] cpu_id=2 tvmode=0 [ 0.984526@2] dolby_vision_init_receiver(dvel) [ 0.984528@2] dolby_vision_init_receiver: dvel [ 0.984585@2] amdolby_vision_probe: ok [ 0.984681@2] reg base = ffffff8008639000 [ 0.984699@2] gdc ff950000.gdc: assigned reserved memory node linux,gdc_cma [ 0.984889@2] vm_init . [ 0.985369@2] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller [ 0.985892@2] meson-mmc: >>>>>>>>hostbase ffffff8008685000, dmode [ 1.027283@2] meson-mmc: meson_mmc_probe() : success! [ 1.032407@5] meson-mmc: >>>>>>>>hostbase ffffff800868e000, dmode [ 1.032430@5] meson-mmc: gpio_cd = 1ca [ 1.071302@0] meson-mmc: meson_mmc_probe() : success! [ 1.073397@0] meson-mmc: >>>>>>>>hostbase ffffff80086a8000, dmode [ 1.078681@2] meson-aml-mmc ffe07000.emmc: divider requested rate 200000000 != actual rate 199999997: ret=0 [ 1.079164@2] meson-mmc: Data 1 aligned delay is 0 [ 1.079728@2] hdmitx: system: plugin [ 1.111300@3] meson-mmc: meson_mmc_probe() : success! [ 1.111402@3] amlogic mtd driver init [ 1.111836@3] Smartcard: smc0_enable_level: 1 [ 1.111838@3] Smartcard: enable_pin: -->(0) [ 1.111852@3] Smartcard: cannot find resource "smc0_clk_pinmux_reg" [ 1.111854@3] Smartcard: cannot find resource "smc0_clk_pinmux_bit" [ 1.111856@3] Smartcard: cannot find resource "smc0_clk_oen_reg" [ 1.111857@3] Smartcard: cannot find resource "smc0_clk_out_reg" [ 1.111860@3] Smartcard: cannot find resource "smc0_clk_oebit" [ 1.111861@3] Smartcard: cannot find resource "smc0_clk_oubit" [ 1.111935@3] Smartcard: request detect pin gpio(70) okay [ 1.111938@3] Smartcard: smc0_clock_source: 0 [ 1.111939@3] Smartcard: smc0_det_invert: 0 [ 1.111944@3] gpiod_direction_output: invalid GPIO (errorpointer) [ 1.112049@3] Smartcard: SMC CLK SOURCE - 499998KHz [ 1.112054@3] Smartcard: REG0: 0x001d0174 [ 1.112055@3] Smartcard: etu :372 [ 1.112056@3] Smartcard: f :372 [ 1.112057@3] Smartcard: d :1 [ 1.112058@3] Smartcard: freq :4000 [ 1.112059@3] Smartcard: REG1: 0x2cff9c40 [ 1.112061@3] Smartcard: REG2: 0x21b7b448 [ 1.112062@3] Smartcard: recv_inv:0 [ 1.112063@3] Smartcard: recv_lsb:0 [ 1.112064@3] Smartcard: recv_par:0 [ 1.112065@3] Smartcard: recv_npa:1 [ 1.112065@3] Smartcard: xmit_inv:0 [ 1.112066@3] Smartcard: xmit_lsb:0 [ 1.112067@3] Smartcard: xmit_par:0 [ 1.112068@3] Smartcard: xmit_rep:1 [ 1.112069@3] Smartcard: xmit_try:1 [ 1.112070@3] Smartcard: clk_tcnt:123 freq_cpu:499998 [ 1.112071@3] Smartcard: INTR: 0x01fe0000 [ 1.112072@3] Smartcard: REG5: 0x000003e7 [ 1.112073@3] Smartcard: REG6: 0x00414d00 [ 1.112074@3] Smartcard: N :0 [ 1.112075@3] Smartcard: cwi :13 [ 1.112076@3] Smartcard: bgt :22 [ 1.112077@3] Smartcard: bwi :4 [ 1.112251@3] cectx ff80023c.aocec: cec driver date:Ver 2019/1/10 [ 1.112251@3] [ 1.112414@3] input: cec_input as /devices/virtual/input/input1 [ 1.112484@3] cectx ff80023c.aocec: not find 'port_num' [ 1.112486@3] cectx ff80023c.aocec: using cec:1 [ 1.112500@3] cectx ff80023c.aocec: no hdmirx regs [ 1.112502@3] cectx ff80023c.aocec: no hhi regs [ 1.112509@3] cectx ff80023c.aocec: not find 'output' [ 1.113963@3] cectx ff80023c.aocec: irq cnt:2 [ 1.114171@5] cectx ff80023c.aocec: wakeup_reason:0xec133af5 [ 1.114238@5] cectx ff80023c.aocec: cev val1: 0x0;val2: 0x0 [ 1.114241@5] cectx ff80023c.aocec: aml_cec_probe success end [ 1.114359@5] unifykey: storage in base: 0xffffffc005000000 [ 1.114360@5] unifykey: storage out base: 0xffffffc005040000 [ 1.114362@5] unifykey: storage block base: 0xffffffc005080000 [ 1.114363@5] unifykey: probe done! [ 1.114546@5] unifykey: no efuse-version set, use default value: -1 [ 1.114547@5] unifykey: key unify config unifykey-num is 15 [ 1.114592@5] unifykey: key unify fact unifykey-num is 15 [ 1.114595@5] unifykey: unifykey_devno: 1f400000 [ 1.114693@5] unifykey: device unifykeys created ok [ 1.114715@5] unifykey: aml_unifykeys_init done! [ 1.114755@5] meson ts init [ 1.114773@5] tsensor id: 0 [ 1.114853@5] tsensor trim info: 0x0! [ 1.114854@5] thermal calibration type not support: 0x0! [ 1.114857@5] meson-tsensor ff634800.p_tsensor: Failed to initialize tsensor [ 1.114868@5] meson-tsensor: probe of ff634800.p_tsensor failed with error 34 [ 1.114882@5] meson ts init [ 1.114894@5] tsensor id: 1 [ 1.114948@5] tsensor trim info: 0x0! [ 1.114949@5] thermal calibration type not support: 0x0! [ 1.114951@5] meson-tsensor ff634c00.d_tsensor: Failed to initialize tsensor [ 1.114958@5] meson-tsensor: probe of ff634c00.d_tsensor failed with error 34 [ 1.115022@5] audio_dsp: [dsp]register dsp to char divece(257) [ 1.115094@5] amaudio: amaudio: driver amaudio init! [ 1.115248@5] amaudio: amaudio_init - amaudio: driver amaudio succuess! [ 1.115505@5] sysled: module init [ 1.115643@5] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog [ 1.115751@5] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done [ 1.116014@5] amlogic rfkill init [ 1.116091@5] enter bt_probe of_node [ 1.116099@5] not get gpio_en [ 1.116106@5] power on valid level is high [ 1.116106@5] bt: power_on_pin_OD = 0; [ 1.116107@5] bt: power_off_flag = 1; [ 1.116109@5] dis power down = 0; [ 1.143357@5] BLASTER Driver Init [ 1.143658@5] meson-saradc ff809000.saradc: set delay per tick to <1ms> by default. [ 1.143660@5] meson-saradc ff809000.saradc: set ticks per period to <1> by default. [ 1.144702@4] dmc_monitor_probe [ 1.145395@4] aml_atvdemod_init: OK, atv demod version: V2.06. [ 1.145478@4] defendkey ff630218.defendkey: Reserved memory is not enough! [ 1.145484@4] defendkey: probe of ff630218.defendkey failed with error -22 [ 1.145736@5] usbcore: registered new interface driver snd-usb-audio [ 1.146329@5] aml_codec_T9015 ff632000.t9015: aml_T9015_audio_codec_probe [ 1.146374@5] aml_codec_T9015 is used by auge chipset, tdmout:1 [ 1.147705@5] asoc debug: aml_audio_controller_probe-115 [ 1.148475@5] aml_card_probe error ret:-517 [ 1.148584@5] aml_tdm_platform_probe, tdm ID = 0 [ 1.148597@5] TDM id 0 i2s2hdmi:0 [ 1.148879@5] aml_tdm_platform_probe, tdm ID = 1 [ 1.148912@5] TDM id 1 samesource_sel:3 [ 1.148914@5] TDM id 1 i2s2hdmi:0 [ 1.149065@5] aml_tdm_platform_probe, tdm ID = 2 [ 1.149078@5] TDM id 2 i2s2hdmi:0 [ 1.149229@5] aml_tdm_platform_probe, tdm ID = 2 [ 1.149241@5] TDM id 2 i2s2hdmi:1 [ 1.149574@5] aml_spdif_platform_probe, spdif ID = 0 [ 1.149728@5] SPDIF id 0 asrc_id:0 auto_asrc:0 [ 1.149795@5] spdifout_play_with_zerodata, spdif id:0 enable:0 [ 1.149798@5] spdif_a fifo ctrl, frddr:0 type:3, 32 bits [ 1.149803@5] spdif_info: rate: 48000, channel status ch0_l:0x100, ch0_r:0x100, ch1_l:0x200, ch1_r:0x200 [ 1.149807@5] hdmitx: audio: aout notify format CT_PCM [ 1.149809@5] hdmitx: hw: set audio [ 1.149814@5] hdmitx: hw: hdmitx tx_aud_src = 0 [ 1.149825@0] hdmitx: system: irq 80000001 [ 1.149826@5] hdmitx: fs = 3, cd = 4, tmds_clk = 0 [ 1.149829@5] hdmitx: hw: aud_n_para = 6144 [ 1.149836@5] hdmitx: hw: set channel status [ 1.149865@5] hdmitx: audio: Audio Type: PCM [ 1.149868@5] hdmitx: audio: set audio param [ 1.149871@5] spdif_a is set to enable [ 1.149875@5] aml_spdif_platform_probe, register soc platform [ 1.149895@5] aml_spdif_platform_probe, spdif ID = 1 [ 1.149922@0] hdmitx: Start = 0x10000100 End = 0x100001ff [ 1.149927@0] hdmitx: [0x10000103]: 0x00000008 [ 1.149929@0] hdmitx: [0x10000104]: 0x00000001 [ 1.149931@0] hdmitx: [0x10000105]: 0x00000002 [ 1.149949@5] spdifout_play_with_zerodata, spdif id:1 enable:0 [ 1.149952@5] spdif_b fifo ctrl, frddr:0 type:3, 32 bits [ 1.149958@5] spdif_info: rate: 48000, channel status ch0_l:0x100, ch0_r:0x100, ch1_l:0x200, ch1_r:0x200 [ 1.149967@5] spdif_b is set to enable [ 1.149971@5] aml_spdif_platform_probe, register soc platform [ 1.149978@0] hdmitx: [0x10000170]: 0x00000010 [ 1.149986@0] hdmitx: [0x10000180]: 0x000000ff [ 1.149988@0] hdmitx: [0x10000181]: 0x000000ff [ 1.149991@0] hdmitx: [0x10000182]: 0x00000003 [ 1.149993@0] hdmitx: [0x10000183]: 0x00000007 [ 1.149995@0] hdmitx: [0x10000184]: 0x0000003f [ 1.149997@0] hdmitx: [0x10000185]: 0x00000002 [ 1.149999@0] hdmitx: [0x10000187]: 0x000000ff [ 1.150002@0] hdmitx: [0x10000188]: 0x00000003 [ 1.150264@5] audio_ddr_mngr: 0, irqs toddr 23, frddr 26 [ 1.150266@5] audio_ddr_mngr: 1, irqs toddr 24, frddr 27 [ 1.150267@5] audio_ddr_mngr: 2, irqs toddr 25, frddr 28 [ 1.150424@5] audiolocker_platform_probe [ 1.151265@5] Register vad [ 1.151265@5] GACT probability NOT on [ 1.151289@5] Mirror/redirect action on [ 1.151293@5] u32 classifier [ 1.151294@5] Actions configured [ 1.151297@5] Netfilter messages via NETLINK v0.30. [ 1.151436@5] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 1.151583@5] ctnetlink v0.93: registering with nfnetlink. [ 1.151813@3] xt_time: kernel timezone is -0000 [ 1.151861@3] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 1.152121@3] IPv4 over IPsec tunneling driver [ 1.152397@3] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.152488@3] arp_tables: arp_tables: (C) 2002 David S. Miller [ 1.152537@3] Initializing XFRM netlink socket [ 1.152795@3] NET: Registered protocol family 10 [ 1.153419@3] mip6: Mobile IPv6 [ 1.153429@3] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.153824@3] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.154251@3] NET: Registered protocol family 17 [ 1.154260@3] NET: Registered protocol family 15 [ 1.154274@3] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.154327@3] Bluetooth: RFCOMM TTY layer initialized [ 1.154331@3] Bluetooth: RFCOMM socket layer initialized [ 1.154353@3] Bluetooth: RFCOMM ver 1.11 [ 1.154357@3] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.154358@3] Bluetooth: BNEP filters: protocol multicast [ 1.154363@3] Bluetooth: BNEP socket layer initialized [ 1.154365@3] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.154368@3] Bluetooth: HIDP socket layer initialized [ 1.154414@3] l2tp_core: L2TP core driver, V2.0 [ 1.154419@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 1.154421@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.154429@3] l2tp_netlink: L2TP netlink interface [ 1.154450@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.154459@3] l2tp_debugfs: L2TP debugfs support [ 1.154461@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.154542@3] NET: Registered protocol family 35 [ 1.154629@3] Key type dns_resolver registered [ 1.154929@3] Registered swp emulation handler [ 1.154936@3] Registered cp15_barrier emulation handler [ 1.154943@3] Registered setend emulation handler [ 1.155197@3] registered taskstats version 1 [ 1.160511@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host [ 1.210958@2] hdmitx: edid: EDID Parser: [ 1.210962@2] hdmitx: edid: get dtd0 vic: 97 [ 1.210965@2] hdmitx: edid: get dtd1 vic: 16 [ 1.210975@2] hdmitx: edid: find IEEEOUT [ 1.210995@2] hdmitx: edid: check sum valid [ 1.210996@2] hdmitx: edid: check sum valid [ 1.210999@2] hdmitx: edid: update rx hdr info d [ 1.211001@2] hdmitx: edid: check sum valid [ 1.211002@2] hdmitx: edid: check sum valid [ 1.211004@2] hdmitx: edid: blk0 raw data [ 1.211020@2] hdmitx: edid: [ 1.211020@2] 00ffffffffffff004c2d140f000e0001011c0103805932780a23ada4544d9926 [ 1.211020@2] 0f474abdef80714f81c0810081809500a9c0b300010108e80030f2705a80b058 [ 1.211020@2] 8a00501d7400001e023a801871382d40582c4500501d7400001e000000fd0018 [ 1.211020@2] 4b0f873c000a202020202020000000fc0053414d53554e470a20202020200177 [ 1.211020@2] [ 1.211020@2] [ 1.211022@2] hdmitx: edid: blk1 raw data [ 1.211037@2] hdmitx: edid: [ 1.211037@2] 020356f05761101f041305142021225d5e5f6065666263640716031229090707 [ 1.211037@2] 15075057070183010000e2004fe305c3016e030c001000b83c20008001020304 [ 1.211037@2] 67d85dc401788003e3060d01e30f01e0e5018b849001011d80d0721c1620102c [ 1.211037@2] 2580501d7400009e662156aa51001e30468f3300501d7400001e000000000099 [ 1.211037@2] [ 1.211037@2] [ 1.211040@2] hdmitx: system: update physcial size: 890 500 [ 1.211044@2] hdmitx: system: get current mode: 2160p50hz [ 1.211045@2] hdmitx: edid: update rx hdr info d [ 1.211046@2] hdmitx: system: update physcial size: 890 500 [ 1.211056@2] hdmitx: system: [set_disp_mode_auto_int] ALREADY init VIC = 96 [ 1.211059@2] hdmitx: hw: set audio [ 1.211060@2] hdmitx: hw: hdmitx tx_aud_src = 0 [ 1.211072@2] hdmitx: fs = 3, cd = 4, tmds_clk = 594000 [ 1.211073@2] hdmitx: hw: aud_n_para = 6144 [ 1.211081@2] hdmitx: hw: set channel status [ 1.211110@2] hdmitx: audio: Audio Type: PCM [ 1.327701@2] meson-mmc: emmc: clk 199999997 tuning start [ 1.329313@2] meson-mmc: emmc: rx_tuning_result[0] = 40 [ 1.329358@2] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac [ 1.331008@2] meson-mmc: emmc: rx_tuning_result[2] = 40 [ 1.331964@2] meson-mmc: emmc: rx_tuning_result[3] = 40 [ 1.332910@2] meson-mmc: emmc: rx_tuning_result[4] = 40 [ 1.332932@2] meson-mmc: emmc: best_win_start =2, best_win_size =4 [ 1.333576@2] meson-mmc: emmc: sd_emmc_regs->gclock=0x10000345,sd_emmc_regs->gadjust=0x42000 [ 1.334701@2] emmc: new HS200 MMC card at address 0001 [ 1.335136@2] emmc: clock 199999997, 8-bit-bus-width [ 1.335136@2] [ 1.336044@2] mmcblk0: emmc:0001 AJTD4R 14.6 GiB [ 1.336395@2] mmcblk0boot0: emmc:0001 AJTD4R partition 1 4.00 MiB [ 1.337081@2] mmcblk0boot1: emmc:0001 AJTD4R partition 2 4.00 MiB [ 1.337784@2] mmcblk0rpmb: emmc:0001 AJTD4R partition 3 4.00 MiB [ 1.338959@2] meson-mmc: Enter aml_emmc_partition_ops [ 1.339303@2] meson-mmc: [mmc_read_partition_tbl] mmc read partition OK! [ 1.339696@2] meson-mmc: add_emmc_partition [ 1.340250@2] meson-mmc: [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000 [ 1.341329@2] meson-mmc: [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000 [ 1.342401@2] meson-mmc: [mmcblk0p03] cache offset 0x000006c00000, size 0x000000000000 [ 1.343494@2] meson-mmc: [mmcblk0p04] env offset 0x000007400000, size 0x000000800000 [ 1.344558@2] meson-mmc: [mmcblk0p05] recovery offset 0x000008400000, size 0x000004000000 [ 1.345636@2] meson-mmc: [mmcblk0p06] boot offset 0x00000cc00000, size 0x000002000000 [ 1.346715@2] meson-mmc: [mmcblk0p07] dreambox-rootfs offset 0x00000f400000, size 0x000100000000 [ 1.347809@2] meson-mmc: [mmcblk0p08] dreambox-data offset 0x00010fc00000, size 0x000294200000 [ 1.348825@2] card key: card_blk_probe. [ 1.349257@2] emmc_key_init:183 emmc key lba_start:0x12020,lba_end:0x12220 [ 1.350046@2] emmc key: emmc_key_init:205 ok. [ 1.350546@2] meson-mmc: amlmmc_dtb_init: register dtb chardev [ 1.353070@2] meson-mmc: calc 5299c5b5, store 5299c5b5 [ 1.354837@2] meson-mmc: calc 5299c5b5, store 5299c5b5 [ 1.354858@2] meson-mmc: total valid 2 [ 1.355293@2] meson-mmc: amlmmc_dtb_init: register dtb chardev OK [ 1.355907@2] meson-mmc: Exit aml_emmc_partition_ops OK. [ 1.663209@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.663242@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.664377@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x20010010 [ 1.665161@3] xhci-hcd xhci-hcd.0.auto: irq 14, io mem 0xff500000 [ 1.666199@3] hub 1-0:1.0: USB hub found [ 1.666299@3] hub 1-0:1.0: 2 ports detected [ 1.666930@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.667431@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.668349@3] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.669518@3] hub 2-0:1.0: USB hub found [ 1.669727@3] hub 2-0:1.0: 1 port detected [ 1.670963@3] aml_dai_spdif_probe [ 1.670983@3] aml_dai_spdif_probe [ 1.671093@3] aml_dai_set_spdif_fmt , fmt 0x4000 [ 1.671141@3] aml_spdif_new spdif_b, clk continuous:1 [ 1.671144@3] spdifout_play_with_zerodata_free, spdif id:1 [ 1.671493@3] asoc-aml-card auge_sound: dummy <-> SPDIF-B mapping ok [ 1.671810@3] aml_dai_set_spdif_fmt , fmt 0x4000 [ 1.671851@3] aml_spdif_new spdif_a, clk continuous:1 [ 1.671854@3] spdifout_play_with_zerodata_free, spdif id:0 [ 1.671942@3] asoc-aml-card auge_sound: dummy <-> SPDIF mapping ok [ 1.672521@3] aml_dai_set_tdm_slot(), txmask(0xff), rxmask(0xff) [ 1.672523@3] lanes_out_cnt(1), lanes_in_cnt(1) [ 1.672525@3] lanes_oe_out_cnt(0), lanes_oe_in_cnt(0) [ 1.672527@3] lanes_lb_cnt(0) [ 1.672529@3] slots(8), slot_width(32) [ 1.672536@3] asoc aml_dai_set_tdm_fmt, 0x4004, ffffffc025bb6618, id(1), clksel(1) [ 1.672542@3] master_mode(1), binv(0), finv(0) out_skew(2), in_skew(3) [ 1.673444@3] asoc-aml-card auge_sound: multicodec <-> TDM-B mapping ok [ 1.674488@3] snd_card_add_kcontrols card:ffffffc025468818 [ 1.674664@3] effect_v2 is not init [ 1.675059@3] Not init vad [ 1.675061@3] Failed to add VAD controls [ 1.675925@3] eq/drc v1 function enable [ 1.703358@3] set av out GPIOF_OUT_INIT_HIGH! [ 1.703512@5] hctosys: unable to open rtc device (rtc0) [ 1.704033@5] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc026563c00) [ 1.704066@5] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0 [ 1.704820@5] dwc_otg ff400000.dwc2_a: base=0xffffff8008cc0000 [ 1.704823@5] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc025436e00 [ 1.804943@5] dwc_otg: Core Release: 3.30a [ 1.804963@5] dwc_otg: Setting default values for core params [ 1.805435@5] dwc_otg: curmode: 0, host_only: 0 [ 1.805963@5] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT [ 1.818117@5] dwc_otg: Using Buffer DMA mode [ 1.818138@5] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1 [ 1.818574@5] dwc_otg: Working on port type = SLAVE [ 1.819134@5] dwc_otg: Dedicated Tx FIFOs mode [ 1.821240@5] meson_cdev probe [ 1.821298@5] meson_cdev index: 0 [ 1.821400@5] meson_cdev index: 1 [ 1.821759@5] meson_cdev index: 2 [ 1.822088@5] cpucore_cooling_register, max_cpu_core_num:2 [ 1.822766@5] meson_cdev index: 3 [ 1.823096@5] cpucore_cooling_register, max_cpu_core_num:4 [ 1.823787@5] meson_cdev index: 4 [ 1.824119@5] meson_cdev index: 5 [ 1.824513@5] find tzd id: 0 [ 1.824912@5] find tzd id: 0 [ 1.825224@5] find tzd id: 0 [ 1.825506@5] meson_cdev probe done [ 1.825947@5] gxbb_pm: enter meson_pm_probe! [ 1.826405@5] gxbb_pm: meson_pm_probe done [ 1.827059@5] ALSA device list: [ 1.827196@5] #0: AML-AUGESOUND [ 1.935282@5] prepare_namespace() wait 79 [ 1.935320@5] md: Waiting for all devices to be available before autodetect [ 1.935898@5] md: If you don't use raid, use raid=noautodetect [ 1.936955@5] md: Autodetecting RAID arrays. [ 1.937058@5] md: Scanned 0 and added 0 devices. [ 1.937587@5] md: autorun ... [ 1.937928@5] md: ... autorun DONE. [ 1.939025@5] EXT4-fs (mmcblk0p7): INFO: recovery required on readonly filesystem [ 1.939243@5] EXT4-fs (mmcblk0p7): write access will be enabled during recovery [ 1.949423@3] EXT4-fs (mmcblk0p7): recovery complete [ 1.950246@3] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null) [ 1.950574@3] VFS: Mounted root (ext4 filesystem) readonly on device 179:7. [ 1.951874@3] devtmpfs: mounted [ 1.953610@3] Freeing unused kernel memory: 5312K [ 2.022954@0] systemd[1]: systemd 232 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 2.025021@0] systemd[1]: Detected architecture arm64. [ 2.035767@0] systemd[1]: Set hostname to . [ 2.059973@5] systemd-fstab-generator[176]: Checking was requested for "rootfs", but it is not a device. [ 2.108149@5] systemd[1]: Listening on udev Control Socket. [ 2.119563@0] systemd[1]: Listening on Journal Socket (/dev/log). [ 2.131555@0] systemd[1]: Listening on Journal Socket. [ 2.143498@0] systemd[1]: Listening on udev Kernel Socket. [ 2.155426@0] systemd[1]: Reached target Remote File Systems. [ 2.167497@0] systemd[1]: Listening on Syslog Socket. [ 2.179408@0] systemd[1]: Reached target Swap. [ 2.302682@5] EXT4-fs (mmcblk0p7): re-mounted. Opts: (null) [ 2.368788@5] dhd: loading out-of-tree module taints kernel. [ 2.396117@5] dhd_module_init: in Dongle Host Driver, version 1.363.59.144.10 (r) [ 2.396510@5] ======== dhd_wlan_init_plat_data ======== [ 2.397105@5] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1 [ 2.397694@5] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1 [ 2.398315@5] dhd_wlan_init_gpio: host_oob_irq: 69 [ 2.398864@5] dhd_wlan_init_gpio: host_oob_irq_flags=0x418 [ 2.399518@5] dhd_wifi_platform_load: Enter [ 2.399988@5] Power-up adapter 'DHD generic adapter' [ 2.400544@5] wifi_platform_set_power = 1 [ 2.401004@5] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 2.401626@5] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 471 [ 2.558285@1] systemd-journald[182]: Received request to flush runtime journal from PID 1 [ 2.583336@2] hdmitx: hdmitx_aud_hpd_plug_handler state:2 [ 2.607485@0] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.615629@5] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 471 [ 2.631327@0] usb-storage 2-1:1.0: USB Mass Storage device detected [ 2.676754@0] scsi host0: usb-storage 2-1:1.0 [ 2.728616@2] mali ffe40000.bifrost: Continuing without Mali regulator control [ 2.728877@2] mali ffe40000.bifrost: max pp is 2 [ 2.729341@2] mali ffe40000.bifrost: set min pp to default 1 [ 2.729988@2] mali ffe40000.bifrost: min pp is 1 [ 2.730519@2] mali ffe40000.bifrost: set min clk default to 0 [ 2.731204@2] mali ffe40000.bifrost: min clk is 0 [ 2.731855@2] mali ffe40000.bifrost: hiu io source 0xffffff8008fe8000 [ 2.732487@2] mali ffe40000.bifrost: hiu io source 0xffffff8008fea000 [ 2.733230@2] mali ffe40000.bifrost: num of pp used most of time 1 [ 2.733939@2] mali ffe40000.bifrost: clock dvfs cfg table size is 6 [ 2.734681@2] mali ffe40000.bifrost: max clk set 4 [ 2.735209@2] mali ffe40000.bifrost: max clk is 4 [ 2.735774@2] mali ffe40000.bifrost: turbo clk set to 5 [ 2.736359@2] mali ffe40000.bifrost: turbo clk is 5 [ 2.736929@2] mali ffe40000.bifrost: default clk set to 4 [ 2.737548@2] mali ffe40000.bifrost: default clk is 4 [ 2.738140@2] mali ffe40000.bifrost: ====================0==================== [ 2.738140@2] clk_freq= 285714285, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshod=<100 190>, clk_sample=285 [ 2.740228@2] mali ffe40000.bifrost: ====================1==================== [ 2.740228@2] clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshod=<152 207>, clk_sample=400 [ 2.742298@2] mali ffe40000.bifrost: ====================2==================== [ 2.742298@2] clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<180 220>, clk_sample=500 [ 2.755291@2] mali ffe40000.bifrost: ====================3==================== [ 2.755291@2] clk_freq= 666666666, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshod=<210 236>, clk_sample=666 [ 2.756726@2] mali ffe40000.bifrost: ====================4==================== [ 2.756726@2] clk_freq= 800000000, clk_parent=fclk_div2p5, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=800 [ 2.758814@2] mali ffe40000.bifrost: ====================5==================== [ 2.758814@2] clk_freq= 800000000, clk_parent=fclk_div2p5, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=800 [ 2.774990@2] mali ffe40000.bifrost: clock dvfs table size is 6 [ 2.775592@2] mali_plat=ffffff8001f9a5c0 [ 2.776094@2] find tzd id: 0 [ 2.776237@2] gpu cooling register okay with err=0 [ 2.776903@2] find tzd id: 0 [ 2.777100@2] gpu core cooling register okay with err=0 [ 2.777707@2] shader_present=3, tiler_present=1, l2_present=1 [ 2.778425@2] Mali_pwr_on:gpu_irq : 200 [ 2.787349@5] hrtimer: interrupt took 10583 ns [ 2.787428@5] mali ffe40000.bifrost: GPU identified as 0x2 arch 7.2.1 r0p0 status 0 [ 2.788499@5] mali ffe40000.bifrost: Using coherency mode 0 set from dtb [ 2.799526@4] mali ffe40000.bifrost: Probed as mali0 [ 2.811605@4] ionvid: dbg: ionvideo open [ 2.811738@4] ionvid: dbg: vidioc_close!!!! [ 2.811744@4] ionvid: dbg: vidioc_close [ 2.812998@4] ionvid: dbg: ionvideo open [ 2.813077@4] ionvid: dbg: vidioc_close!!!! [ 2.813084@4] ionvid: dbg: vidioc_close [ 2.816487@3] ionvid: dbg: ionvideo open [ 2.816575@3] ionvid: dbg: vidioc_close!!!! [ 2.816582@3] ionvid: dbg: vidioc_close [ 2.818342@4] ionvid: dbg: ionvideo open [ 2.818430@4] ionvid: dbg: vidioc_close!!!! [ 2.818436@4] ionvid: dbg: vidioc_close [ 2.819108@4] ionvid: dbg: ionvideo open [ 2.819186@4] ionvid: dbg: vidioc_close!!!! [ 2.819192@4] ionvid: dbg: vidioc_close [ 2.819477@4] ionvid: dbg: ionvideo open [ 2.819558@4] ionvid: dbg: vidioc_close!!!! [ 2.819564@4] ionvid: dbg: vidioc_close [ 2.822214@4] ionvid: dbg: ionvideo open [ 2.822316@4] ionvid: dbg: vidioc_close!!!! [ 2.822322@4] ionvid: dbg: vidioc_close [ 2.824472@4] ionvid: dbg: ionvideo open [ 2.824572@4] ionvid: dbg: vidioc_close!!!! [ 2.824579@4] ionvid: dbg: vidioc_close [ 2.825274@4] ionvid: dbg: ionvideo open [ 2.825352@4] ionvid: dbg: vidioc_close!!!! [ 2.825358@4] ionvid: dbg: vidioc_close [ 3.155282@5] wifi_platform_bus_enumerate device present 1 [ 3.155314@5] ======== Card detection to detect SDIO card! ======== [ 3.157222@0] meson-mmc: sdio: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 3.157346@0] meson-mmc: sdio: err: wait for desc write back, bus_fsm:0x7 [ 3.158142@0] meson-mmc: meson_mmc_irq_thread_v3 557 sdio: cmd:52 [ 3.159867@0] meson-mmc: sdio: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 3.159984@0] meson-mmc: sdio: err: wait for desc write back, bus_fsm:0x7 [ 3.160771@0] meson-mmc: meson_mmc_irq_thread_v3 557 sdio: cmd:52 [ 3.165933@0] meson-mmc: sdio: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 3.166049@0] meson-mmc: sdio: err: wait for desc write back, bus_fsm:0x7 [ 3.166852@0] meson-mmc: meson_mmc_irq_thread_v3 557 sdio: cmd:8 [ 3.205752@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes) [ 3.208604@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes) [ 3.211456@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes) [ 3.216570@5] sdio: queuing unknown CIS tuple 0x80 (7 bytes) [ 3.317330@5] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0 [ 3.317808@5] meson-mmc: Data 1 aligned delay is 0 [ 3.318357@5] meson-mmc: sdio: clk 199999997 tuning start [ 3.319004@5] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac [ 3.320671@5] meson-mmc: sdio: rx_tuning_result[1] = 40 [ 3.321536@5] meson-mmc: sdio: rx_tuning_result[2] = 40 [ 3.322403@5] meson-mmc: sdio: rx_tuning_result[3] = 40 [ 3.323458@5] meson-mmc: sdio: rx_tuning_result[4] = 40 [ 3.323481@5] meson-mmc: sdio: best_win_start =1, best_win_size =4 [ 3.324125@5] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x32000 [ 3.328670@5] sdio: new ultra high speed SDR104 SDIO card at address 0001 [ 3.328808@5] sdio: clock 199999997, 4-bit-bus-width [ 3.328808@5] [ 3.329619@5] meson-mmc: [sdio_reinit] finish [ 3.346144@5] bcmsdh_register: register client driver [ 3.346281@5] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter [ 3.346735@4] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter [ 3.347225@4] bus num (host idx)=2, slot num (rca)=1 [ 3.347811@4] found adapter info 'DHD generic adapter' [ 3.348387@4] Wifi: bcmdhd_mem_prealloc: sectoin 3, size 139264 [ 3.349082@4] alloc static buf at ffffffc025e00000! [ 3.349624@4] Wifi: bcmdhd_mem_prealloc: sectoin 4, size 0 [ 3.350307@4] sdioh_attach: set sd_f2_blocksize 256 [ 3.351162@4] dhdsdio_probe : no mutex held. set lock [ 3.351542@4] F1 signature read @0x18000000=0x17224356 [ 3.355422@4] F1 signature OK, socitype:0x1 chip:0x4354 rev:0x2 pkg:0x2 [ 3.356073@4] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000 [ 3.356402@4] Wifi: bcmdhd_mem_prealloc: sectoin 7, size 30240 [ 3.357030@4] dhd_conf_set_chiprev: chip=0x4354, chiprev=2 [ 3.357692@4] Wifi: bcmdhd_mem_prealloc: sectoin 0, size 10544 [ 3.358581@4] Wifi: bcmdhd_mem_prealloc: sectoin 5, size 65536 [ 3.359074@4] wl_create_event_handler(): thread:wl_event_handler:121 started [ 3.359885@4] wl_escan_attach: Enter [ 3.360224@4] wl_escan_init: Enter [ 3.361325@4] tsk Enter, tsk = 0xffffffc024000cd8 [ 3.361364@4] wl_create_event_handler(): thread:wl_escan_handler:122 started [ 3.362061@4] tsk Enter, tsk = 0xffffffc024030198 [ 3.362585@4] dhd_attach(): thread:dhd_watchdog_thread:123 started [ 3.363566@4] dhd_attach(): thread:dhd_dpc:124 started [ 3.363917@4] dhd_attach(): thread:dhd_rxf:125 started [ 3.364464@4] dhd_deferred_work_init: work queue initialized [ 3.365132@4] Wifi: bcmdhd_mem_prealloc: sectoin 1, size 10524 [ 3.365792@4] Wifi: bcmdhd_mem_prealloc: sectoin 2, size 65536 [ 3.366506@5] dhd_rxf_thread: set rxf_cpucore 2 [ 3.378412@4] Dongle Host Driver, version 1.363.59.144.10 (r) [ 3.378801@4] Register interface [wlan0] MAC: cc:4b:73:20:9d:5e [ 3.378801@4] [ 3.379451@5] wl_event_handler: was terminated [ 3.379828@4] wl_destroy_event_handler(): thread:wl_event_handler:121 terminated OK [ 3.380702@4] dhd_wl_ioctl: returning as busstate=0 [ 3.381298@4] bcmsdh_oob_intr_unregister: Enter [ 3.381779@4] bcmsdh_oob_intr_unregister: irq is not registered [ 3.382463@4] dhd_txglom_enable: enable 0 [ 3.382920@4] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0, txglom_bucket_size=0 [ 3.383861@4] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=-1 [ 3.384779@4] dhd_conf_set_txglom_params: tx_in_rx=1, txinrx_thres=128, dhd_txminmax=-1 [ 3.385699@4] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=0 [ 3.386489@4] sdioh_set_mode: set txglom_mode to multi-desc [ 3.387129@4] dhd_bus_devreset: WLAN OFF DONE [ 3.387701@4] wifi_platform_set_power = 0 [ 3.388100@4] ======== PULL WL_REG_ON(-1) LOW! ======== [ 3.388699@4] dhdsdio_probe : the lock is released. [ 3.389305@4] dhd_module_init: Exit err=0 [ 3.393254@5] stb_core: module license 'Proprietary' taints kernel. [ 3.393337@5] Disabling lock debugging due to kernel taint [ 3.400742@5] No find node. [ 3.400767@5] register clk_set_setting cpu[41] [ 3.402966@4] Registered firmware driver success. [ 3.403696@4] Try to load video/h264_enc.bin ... [ 3.405083@4] load firmware size : 76288, Name : video/h264_enc.bin. [ 3.405187@4] the fw pack ver v0.0 is too lower. [ 3.405701@4] it may work abnormally so need to be update in time. [ 3.406821@4] Try to load video/video_ucode.bin ... [ 3.414554@5] load firmware size : 992000, Name : video/video_ucode.bin. [ 3.417094@5] Try to load video/video_ucode_old.bin ... [ 3.422818@5] load firmware size : 768768, Name : video/video_ucode_old.bin. [ 3.443188@5] Amlogic A/V streaming port init [ 3.446425@4] get gate demux control ok ffffffc025678a80 [ 3.446466@4] get gate parser_top control ok ffffffc025678f40 [ 3.447094@4] get gate vdec control ok ffffffc002406f40 [ 3.447735@4] get gate clk_81 control ok ffffffc002406e80 [ 3.448315@4] get gate clk_vdec_mux control ok ffffffc002406dc0 [ 3.449005@4] get gate clk_hcodec_mux control ok ffffffc002406d40 [ 3.449706@4] get gate clk_hevc_mux control ok ffffffc002406cc0 [ 3.450391@4] get gate clk_hevcb_mux control ok ffffffc002406c00 [ 3.451049@4] get gate ahbarb0 control ok ffffffc002406b40 [ 3.451750@4] get gate asyncfifo control failed (null) [ 3.454290@5] fp_init [ 3.454504@5] fp_probe [ 3.455733@5] muxval 44102211 [ 3.455899@5] input: dreambox front panel as /devices/virtual/input/input2 [ 3.456849@5] led_set_pattern 0 [ 3.559289@5] retry needed [ 3.562413@5] Amlogic S922x hw demux driver init version 20190814r0 [ 3.562498@5] demux_probe [ 3.562979@5] the demux clock on, ref cnt: 1 [ 3.562984@5] the ahbarb0 clock on, ref cnt: 1 [ 3.562987@5] the parser_top clock on, ref cnt: 1 [ 3.562992@5] init hwdmx single 0 [ 3.563258@5] init hwdmx single 1 [ 3.563656@5] init hwdmx single 2 [ 3.563993@5] afifo0 init [ 3.564475@5] afifo1 init [ 3.581602@5] Amlogic S922x DVB driver init version 20190814r0 [ 3.581638@5] nim_probe [ 3.619285@5] DVB: registering new adapter (Dreambox One) [ 3.619317@5] probe tuner config... [ 3.629068@5] fe: read ret=-6 [ 3.630841@5] Channel A I2C 0x64: [ 3.630857@5] Demod Si2166-60 [ 3.630937@5] Channel B I2C 0x67: [ 3.631334@5] Demod Si2166-60 [ 3.631677@5] Sat Tuner RDA5815 [ 3.632057@5] tuner probe failed [ 3.632559@5] vdec ffffff80024219c0 [ 3.636116@5] dvb_demux_init [ 3.636139@5] dvb_demux_init_single 0 [ 3.636227@5] dvb_ca_init [ 3.636612@5] dvb_dmx_init [ 3.636873@5] dvb_dmxdev_init [ 3.638093@5] single done [ 3.638116@5] dvb_demux_init_single 1 [ 3.638174@5] dvb_ca_init [ 3.638559@5] dvb_dmx_init [ 3.638828@5] dvb_dmxdev_init [ 3.640014@4] single done [ 3.640038@4] dvb_demux_init_single 2 [ 3.640096@4] dvb_ca_init [ 3.640632@5] dvb_dmx_init [ 3.640749@5] dvb_dmxdev_init [ 3.641895@5] single done [ 3.641915@5] dvb_demux_init_single 3 [ 3.641975@5] dvb_ca_init [ 3.642339@5] dvb_dmx_init [ 3.642623@5] dvb_dmxdev_init [ 3.643138@5] single done [ 3.643226@5] dvb_demux_init_single 4 [ 3.643674@5] dvb_ca_init [ 3.644886@4] dvb_dmx_init [ 3.644948@4] dvb_dmxdev_init [ 3.645609@4] single done [ 3.645625@4] dvb_demux_init_single 5 [ 3.645686@4] dvb_ca_init [ 3.646135@4] dvb_dmx_init [ 3.646331@4] dvb_dmxdev_init [ 3.646887@4] single done [ 3.646937@4] dvb_demux_init_single 6 [ 3.647373@4] dvb_ca_init [ 3.647865@4] dvb_dmx_init [ 3.648011@4] dvb_dmxdev_init [ 3.648912@4] single done [ 3.648934@4] dvb_demux_init_single 7 [ 3.649027@4] dvb_ca_init [ 3.649402@3] dvb_dmx_init [ 3.649677@3] dvb_dmxdev_init [ 3.656313@4] single done [ 3.656334@4] dvb_demux_init_single 8 [ 3.656395@4] dvb_ca_init [ 3.657757@5] dvb_dmx_init [ 3.657811@5] dvb_dmxdev_init [ 3.659632@4] single done [ 3.659653@4] dvb_demux_init_single 9 [ 3.659714@4] dvb_ca_init [ 3.660577@5] dvb_dmx_init [ 3.660635@5] dvb_dmxdev_init [ 3.661241@4] single done [ 3.661258@4] dvb_demux_init_single 10 [ 3.661393@4] dvb_ca_init [ 3.662132@4] dvb_dmx_init [ 3.662180@4] dvb_dmxdev_init [ 3.662551@5] single done [ 3.662643@5] dvb_demux_init_single 11 [ 3.663073@5] dvb_ca_init [ 3.663845@5] dvb_dmx_init [ 3.663893@5] dvb_dmxdev_init [ 3.664586@4] single done [ 3.664602@4] dvb_demux_init_single 12 [ 3.664753@4] dvb_ca_init [ 3.665123@4] dvb_dmx_init [ 3.665396@4] dvb_dmxdev_init [ 3.666325@5] single done [ 3.666341@5] dvb_demux_init_single 13 [ 3.666433@5] dvb_ca_init [ 3.667164@5] dvb_dmx_init [ 3.667212@5] dvb_dmxdev_init [ 3.667603@5] single done [ 3.667684@5] dvb_demux_init_single 14 [ 3.668113@5] dvb_ca_init [ 3.668903@5] dvb_dmx_init [ 3.668952@5] dvb_dmxdev_init [ 3.669480@4] single done [ 3.669496@4] dvb_demux_init_single 15 [ 3.669793@4] dvb_ca_init [ 3.670535@4] dvb_dmx_init [ 3.670583@4] dvb_dmxdev_init [ 3.671145@5] single done [ 3.671160@5] dvb_demux_init_single 16 [ 3.672231@5] dvb_ca_init [ 3.672327@5] dvb_dmx_init [ 3.672375@5] dvb_dmxdev_init [ 3.672738@5] single done [ 3.672839@5] demux init done [ 3.673681@5] registered vtuner misc/vtuner0, minor 49 [ 3.673847@5] registered vtuner misc/vtuner1, minor 48 [ 3.674418@5] registered vtuner misc/vtuner2, minor 47 [ 3.675001@5] registered vtuner misc/vtuner3, minor 46 [ 3.676303@5] registered vtuner misc/vtuner4, minor 45 [ 3.676378@5] registered vtuner misc/vtuner5, minor 44 [ 3.676894@5] registered vtuner misc/vtuner6, minor 43 [ 3.677508@5] registered vtuner misc/vtuner7, minor 42 [ 3.678090@5] registered vtuner misc/vtuner8, minor 41 [ 3.678702@5] registered vtuner misc/vtuner9, minor 40 [ 3.679796@5] registered vtuner misc/vtuner10, minor 39 [ 3.679921@5] registered vtuner misc/vtuner11, minor 38 [ 3.680530@5] registered vtuner misc/vtuner12, minor 37 [ 3.681106@5] registered vtuner misc/vtuner13, minor 36 [ 3.683016@5] ble init (1) [ 3.683218@5] input: dreambox remote control (bluetooth le) as /devices/virtual/input/input3 [ 3.686698@5] videograbber:info: Device registered! [ 3.688409@5] input: dreambox remote control (native) as /devices/virtual/input/input4 [ 3.688985@4] input: dreambox advanced remote control (native) as /devices/virtual/input/input5 [ 3.697306@4] amvdec_avs module init [ 3.709461@5] amvdec_h264 module init [ 3.717101@5] amvdec_h265 module init [ 3.723380@5] ammvdec_h264 module init [ 3.731253@5] ammvdec_mpeg4_driver_init_module [ 3.746925@5] amvdec_vc1 module init [ 3.752011@5] amvdec_vp9 module init [ 3.760522@5] VIDEO_SET_STREAMTYPE (0) [ 3.760553@5] the demux clock on, ref cnt: 2 [ 3.760557@5] the parser_top clock on, ref cnt: 2 [ 3.760564@5] the vdec clock on, ref cnt: 1 [ 3.760584@5] the clk_vdec_mux clock on, ref cnt: 1 [ 3.760652@5] vdec mux clock is 499999992 Hz [ 3.760692@5] vdec_create instance ffffff800c9e4000, total 1 [ 3.761045@5] Video stbuf alloced at 0000000040800000, secure = 0, size = 3145728 [ 3.761058@5] vdec_init, dev_name:amvdec_mpeg12, vdec_type=VDEC_TYPE_SINGLE [ 3.761215@5] vdec_init set vfm decoder ffffff800c9e4000 [ 3.761484@5] decoder_bmmu_box_alloc_box, tvp_flags = 0 [ 3.761490@5] [LOCAL], the fw (mpeg12) will be loaded. [ 3.762726@5] vdec_request_irq ffffff800256c518, vmpeg12-irq [ 3.762745@5] DI: di_receiver_event_fun: vframe provider reg ppmgr [ 3.762949@5] vdec_init, vf_provider_name = [ 3.762952@5] vdec_init done [ 3.762976@5] dev ffffffc026531c10 [ 3.763034@5] dma_map_single() done [ 3.763713@5] video first pts = 0 [ 3.763816@5] vdec_request_irq ffffff80024136b0, parser [ 3.764876@5] vdec_connect done [ 3.764900@5] hwdmx1: demux_pcr_start pid ffffffff [ 3.765148@5] the clk_81 clock on, ref cnt: 1 [ 3.765153@5] wait_pcr_count = 0 [ 3.765514@5] [tsync_pcr_start]PCRMASTER started success. [ 3.766134@5] [tsync_pcr_start]usepcr=0 tsync_pcr_inited_mode=0 [ 3.766815@5] hwdmx1: video pcr started [ 3.767254@5] VIDEO_PLAY [ 3.767644@5] VIDEO_CONTINUE [ 3.767877@5] VIDEO_PAUSE 0 [ 3.768301@5] video first checkin pts = 1 [ 3.768653@5] first check in vpts <0x0:0x1> ok! [ 3.768658@5] hwdmx1: old PCR was 0000013a, new is 00000001, video pts is 00000001, diff 3ms (0) [ 3.773038@0] video first pts = 1 [ 3.773079@0] frame duration changed 3840 [ 3.773129@5] DI: di_init_buf:cma alloc req time: 4294671012 ms [ 3.773157@5] di_patch_post_update_mc_sw:0x0->0x2 [ 3.773269@0] frame_rate_changed 25000 (3840) [ 3.774545@5] di_cma_alloc:alloc 10 buffer use 0 ms(4294671012~4294671012) [ 3.781142@2] pre_de_buf_config:4294671020ms 1th source change: 0x0/0/0/0=>0x9000/1280/720/0 [ 3.781472@2] progressive_changed 1 [ 3.783377@5] vdec mux clock is 99999999 Hz [ 3.783380@5] vdec1 video changed to 1280 x 720 25 fps clk->100MHZ [ 3.786419@0] video start! param=1 cur_pcr=ffffbfef [ 3.786512@0] [ 3.786512@0] [amvideo..] saturation_pre:0 hue_pre:0 mab:1000000 [ 3.811944@4] fp: enabled NEC ir decoder [ 3.812468@5] meson-remote ff808040.rc: default protocol = 0x2 and id = 0 [ 3.812606@5] meson-remote ff808040.rc: reg=0x0, val=0x46001e [ 3.813265@5] meson-remote ff808040.rc: reg=0x4, val=0x32000f [ 3.813925@5] meson-remote ff808040.rc: reg=0x8, val=0x1e001a [ 3.814585@5] meson-remote ff808040.rc: reg=0xc, val=0x420028 [ 3.815244@5] meson-remote ff808040.rc: reg=0x10, val=0x304e2013 [ 3.815935@5] meson-remote ff808040.rc: reg=0x18, val=0x5010800 [ 3.816614@5] meson-remote ff808040.rc: reg=0x1c, val=0x9300 [ 3.817265@5] meson-remote ff808040.rc: reg=0x20, val=0xb90b [ 3.817914@5] meson-remote ff808040.rc: reg=0x24, val=0x610050 [ 3.818584@5] meson-remote ff808040.rc: reg=0x28, val=0x780061 [ 3.819254@5] meson-remote ff808040.rc: reg=0x38, val=0x1388 [ 3.830569@0] scsi 0:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 6 [ 3.831671@4] sd 0:0:0:0: [sda] 121610240 512-byte logical blocks: (62.3 GB/58.0 GiB) [ 3.832526@4] sd 0:0:0:0: [sda] Write Protect is off [ 3.832554@4] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 3.832723@4] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.840133@4] sda: sda1 [ 3.841271@4] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 3.919939@5] VIDEO_STOP [ 3.919979@5] hwdmx1: demux_pcr_stop pid ffffffff [ 3.920133@5] the clk_81 clock off, ref cnt: 0 [ 3.920136@5] [tsync_pcr_stop]PCRMASTER stop success. [ 3.920709@5] hwdmx1: video pcr stopped [ 3.921307@5] VIDEO CLOSE [ 3.921449@5] close: decoder open [ 3.922070@5] DI: di_receiver_event_fun , is_bypass() 0 trick_mode 0 bypass_all 0 [ 3.922072@5] di_receiver_event_fun: vf_notify_receiver unreg [ 3.922501@4] DI: di_unreg_process unreg start 1. [ 3.922512@4] keep exit is di [ 3.922721@5] vdec_release instance ffffff800c9e4000, total 1 [ 3.922761@5] the clk_vdec_mux clock off, ref cnt: 0 [ 3.922763@5] the demux clock off, ref cnt: 1 [ 3.922765@5] the parser_top clock off, ref cnt: 1 [ 3.922769@5] the vdec clock off, ref cnt: 0 [ 3.922832@4] timestamp_firstvpts_set ! [ 3.923269@4] video first pts = 0 [ 3.923648@4] audio first pts = 0 [ 3.924028@4] wait_pcr_count = 0 [ 3.924397@4] video stop! [ 3.924715@4] VD1 AFBC 0x0. [ 3.925021@4] DI: di_unreg_process vf unreg cost 4 ms. [ 3.925023@4] DI: di_unreg_process unreg stop 1. [ 3.925046@4] DI: di_uninit_buf keep cur di_buf 0 ( [ 3.925048@4] DI: 0 [ 3.925049@4] DI: 1 [ 3.925050@4] DI: ) [ 3.925067@4] di_patch_post_update_mc_sw:0x2->0x0 [ 3.925069@4] DI: di_unreg_process_irq:cma release req time: -296132 ms [ 3.925080@5] DI: di_cma_release skip buf[0]. [ 3.925080@5] [ 3.925083@5] DI: di_cma_release skip buf[1]. [ 3.925083@5] [ 3.925338@5] di_cma_release:release 8 buffer use 0 ms(4294671164~4294671164) [ 3.975964@4] EXT4-fs (sda1): recovery complete [ 3.975997@4] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 4.545847@1] BT_RADIO going: off [ 4.545877@1] AML_BT: going OFF [ 4.579561@0] eth0: device MAC address 00:09:34:4a:ec:3b [ 4.663265@5] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP. [ 4.666758@5] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.083617@4] fb: malloc_osd_memory, cma:ffffff800ab46050 [ 5.083648@4] fb: malloc_osd_memory, 1228, base:0x000000007f800000, size:8388608 [ 5.084456@4] fb: use ion buffer for fb memory, fb_index=0 [ 5.093350@4] meson-fb meson-fb: create ion_client ffffffc022c44900, handle=ffffffc022fabc00 [ 5.093685@4] meson-fb meson-fb: ion memory(0): created fb at 0x0000000053c00000, size 24 MiB [ 5.094660@4] fb: Frame buffer memory assigned at [ 5.095181@4] fb: 0, phy: 0x0000000053c00000, vir:0xffffff800cb65000, size=24576K [ 5.095181@4] [ 5.096267@4] fb: logo_index=0,fb_index=0 [ 5.096701@4] fb: ---------------clear fb0 memory ffffff800cb65000 [ 5.103626@4] fb: osd[0] canvas.idx =0x40 [ 5.103645@4] fb: osd[0] canvas.addr=0x53c00000 [ 5.103962@4] fb: osd[0] canvas.width=7680 [ 5.104433@4] fb: osd[0] canvas.height=2160 [ 5.104913@4] fb: osd[0] frame.width=1920 [ 5.105373@4] fb: osd[0] frame.height=1080 [ 5.105842@4] fb: osd[0] out_addr_id =0x1 [ 5.106470@4] fb: osd[0] enable: 1 (enigma2) [ 5.126498@3] fb: command 0x40014621 not supported (enigma2) [ 5.176085@4] fb: malloc_osd_memory, cma:ffffff800ab46050 [ 5.176119@4] fb: malloc_osd_memory, 1228, base:0x000000007f800000, size:8388608 [ 5.176917@4] fb: use ion buffer for fb memory, fb_index=1 [ 5.178264@4] meson-fb meson-fb: create ion_client ffffffc022c44900, handle=ffffffc022936d40 [ 5.178593@4] meson-fb meson-fb: ion memory(1): created fb at 0x0000000055400000, size 1 MiB [ 5.179588@4] fb: Frame buffer memory assigned at [ 5.180082@4] fb: 1, phy: 0x0000000055400000, vir:0xffffff800e399000, size=1024K [ 5.180082@4] [ 5.181132@4] fb: logo_index=0,fb_index=1 [ 5.181591@4] fb: ---------------clear fb1 memory ffffff800e399000 [ 5.182570@4] fb: osd[1] canvas.idx =0x43 [ 5.182761@4] fb: osd[1] canvas.addr=0x55400000 [ 5.183300@4] fb: osd[1] canvas.width=128 [ 5.183741@4] fb: osd[1] canvas.height=32 [ 5.184201@4] fb: osd[1] frame.width=32 [ 5.184641@4] fb: osd[1] frame.height=32 [ 5.185091@4] fb: osd[1] out_addr_id =0x2 [ 5.186504@5] fb: malloc_osd_memory, cma:ffffff800ab46050 [ 5.186530@5] fb: malloc_osd_memory, 1228, base:0x000000007f800000, size:8388608 [ 5.187349@5] fb: use ion buffer for fb memory, fb_index=2 [ 5.188538@5] meson-fb meson-fb: create ion_client ffffffc022c44900, handle=ffffffc022fed480 [ 5.188941@5] meson-fb meson-fb: ion memory(2): created fb at 0x0000000055500000, size 1 MiB [ 5.189902@5] fb: Frame buffer memory assigned at [ 5.190423@5] fb: 2, phy: 0x0000000055500000, vir:0xffffff800e49a000, size=1024K [ 5.190423@5] [ 5.191495@5] fb: logo_index=0,fb_index=2 [ 5.191934@5] fb: ---------------clear fb2 memory ffffff800e49a000 [ 5.192917@5] fb: osd[2] canvas.idx =0x41 [ 5.193101@5] fb: osd[2] canvas.addr=0x55500000 [ 5.193622@5] fb: osd[2] canvas.width=128 [ 5.194082@5] fb: osd[2] canvas.height=32 [ 5.194541@5] fb: osd[2] frame.width=32 [ 5.194982@5] fb: osd[2] frame.height=32 [ 5.195447@5] fb: osd[2] out_addr_id =0x3 [ 5.206586@2] fb: vpu clkc clock is 199 MHZ [ 5.206623@2] fb: malloc_osd_memory, cma:ffffff800ab46050 [ 5.207053@2] fb: malloc_osd_memory, 1228, base:0x000000007f800000, size:8388608 [ 5.207922@2] fb: use ion buffer for fb memory, fb_index=3 [ 5.211590@2] meson-fb meson-fb: create ion_client ffffffc022c44900, handle=ffffffc00250fc40 [ 5.211923@2] meson-fb meson-fb: ion memory(3): created fb at 0x0000000055600000, size 8 MiB [ 5.212888@2] fb: Frame buffer memory assigned at [ 5.213409@2] fb: 3, phy: 0x0000000055600000, vir:0xffffff800e59b000, size=8192K [ 5.213409@2] [ 5.214458@2] fb: logo_index=0,fb_index=3 [ 5.214918@2] fb: ---------------clear fb3 memory ffffff800e59b000 [ 5.217959@2] fb: osd[3] canvas.idx =0x42 [ 5.217980@2] fb: osd[3] canvas.addr=0x55600000 [ 5.218296@2] fb: osd[3] canvas.width=128 [ 5.218756@2] fb: osd[3] canvas.height=32 [ 5.219215@2] fb: osd[3] frame.width=32 [ 5.219674@2] fb: osd[3] frame.height=32 [ 5.220106@2] fb: osd[3] out_addr_id =0x4 [ 5.233211@5] fb: osd[0] canvas.idx =0x40 [ 5.233213@5] fb: osd[0] canvas.addr=0x53c00000 [ 5.233215@5] fb: osd[0] canvas.width=5120 [ 5.233216@5] fb: osd[0] canvas.height=2160 [ 5.233217@5] fb: osd[0] frame.width=1280 [ 5.233218@5] fb: osd[0] frame.height=720 [ 5.233219@5] fb: osd[0] out_addr_id =0x1 [ 5.246473@2] fb: outputmode changed to 2160p50hz, reset osd0, (0, 0, 3839, 2159) -> (0, 0, 3839, 2159) [ 5.266458@2] fb: osd_update_disp_axis_hw:pan_data(0,0,1279,719) [ 5.266460@2] fb: osd_update_disp_axis_hw:dispdata(0,0,1279,719) [ 5.306454@3] fb: osd[0] enable: 1 (enigma2) [ 6.684961@1] EXT4-fs (mmcblk0p8): recovery complete [ 6.685005@1] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null) [ 7.696280@2] hdmitx: hdmitx: config: hlg-2 [ 7.696398@2] hdmitx: hdmitx: config: hdr10-2 [ 9.101231@4] led_set_pattern -1 [ 11.287280@2] vout: aml_tvout_mode_work: monitor_timeout [ 18.999569@5] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 18.999964@5] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.241359@1] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead. [ 19.245030@4] demux0: no descrambler support for this source yet