CPU 01
Dreambox DM900
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=000003a1(929)
 temperature=000051bf(20927)
 PV=0000035b(859)
 MV=000003a1(929)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss  07080cd0
_ebss  0713dd70
_end   0713dd90
HEAP @ 07200000
STACK @ 09300000
ARCH: CONFIG OK
CLR BSS 07080cd0 to 0713dd70 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

    ,/
  ,'/___, BOLT v1.18 v1.18 LOCAL BUILD
.'__  ,'  (2017-03-07 20:27:59 cynric@cynric-VirtualBox)
   /,'    Copyright (C) 2017 Broadcom
  /'

Board: BCM97252SSFF
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
CS1: NAND: unrecognized ID: 0x20ffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
card if inited
set pwm to 0/255
disp id 0000
load image
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.928V, T=+22.388C, PV=0.859V, MV=0.929V, FW=30333278 [0.3.2.x]
USB otp=00000040
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
init fp
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
retrying.. card if inited
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
retrying.. card if inited
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
retrying.. card if inited
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
retrying.. card if inited
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
retrying.. card if inited
set pwm to 200/255
TPM error. Please contact Dreambox support