=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.10.28 14:37:07 =~=~=~=~=~=~=~=~=~=~=~= Dreambox DM520 M0CZS L2=1 LLMB=1 BrCfg=E30FB7C6 #@ BCM973625A0 CFE v15.3, Endian Mode: Little Build Date: Thu May 19 18:50:53 2016 (Jann@Cynric) Copyright (C) Broadcom Corporation. Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spare Area Size=16 MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256 CPU speed: 751MHz DDR Frequency: 1061 MHz DDR Mode: DDR3 Total memory(MEMC 0): 512MB MEMC 0 DDR Width: 16 Boot Device: SPI Total flash: 16MB RTS VERSION: rts_hevc10_1067 ETH0_PHY: INT ETH0_MDIO_MODE: 1 ETH0_SPEED: 100 ETH0_PHYADDR: 1 Initializing USB. CFE initialized. ***** DREAMBOX SSBL ***** Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 500ms to cancel Proceeding with autoboot.. You can try aborting with Ctrl+C DM FABTEST CFE starting up Device eth0: hwaddr 00-09-34-FF-00-01, ipaddr 192.168.200.10, mask not set gateway not set, nameserver not set Loader:elf Filesys:raw Dev:flash0.kernel File: Options:bmem=192M@64M console=ttyS0,1000000 root=/dev/nfs nfsroot=192.168.200.1:/srv/nfs/prodtest_dm520 ip=192.168.200.10 Loading: 0x80001000/7448768 0x8071b8c0/240128 Entry address is 0x805af9b0 Closing network eth0 Ethernet link is up: 100 Mbps Full-Duplex Starting program at 0x805af9b0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4-3.9-dm520 (ghost@Client) (gcc version 4.8.1 (GCC) ) #3 SMP Thu May 26 17:47:31 CEST 2016 [ 0.000000] Fetching vars from bootloader... found 13 vars. [ 0.000000] Options: moca=0 sata=0 pcie=0 usb=1 [ 0.000000] Using 512 MB + 0 MB RAM (from CFE) [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a065 (Broadcom BMIPS4380) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] memory: 10000000 @ 20000000 (usable) [ 0.000000] bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00030000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] 0: 0x00020000 -> 0x00030000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81606000 s6336 r8192 d14144 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536 [ 0.000000] Kernel command line: bmem=192M@64M console=ttyS0,1000000 root=/dev/nfs nfsroot=192.168.200.1:/srv/nfs/prodtest_dm520 ip=192.168.200.10 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.000000] Memory: 313536k/524288k available (5874k kernel code, 210752k reserved, 1152k data, 248k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:160 [ 0.000000] Measuring MIPS counter frequency... [ 0.000000] Detected MIPS clock frequency: 751 MHz (375.764 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] Calibrating delay loop... 749.56 BogoMIPS (lpj=374784) [ 0.010000] pid_max: default: 32768 minimum: 301 [ 0.010000] Mount-cache hash table entries: 512 [ 0.011000] Initializing cgroup subsys cpuacct [ 0.012000] Initializing cgroup subsys devices [ 0.012000] Initializing cgroup subsys freezer [ 0.013000] SMP: Booting CPU1... [ 0.017000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.017000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.018000] CPU revision is: 0002a065 (Broadcom BMIPS4380) [ 0.018000] FPU revision is: 00130001 [ 0.027000] SMP: CPU1 is running [ 0.027000] Brought up 2 CPUs [ 0.030000] devtmpfs: initialized [ 0.034000] NET: Registered protocol family 16 [ 0.035000] USB0: power enable is active high; overcurrent is active low [ 0.040000] bio: create slab at 0 [ 0.041000] SCSI subsystem initialized [ 0.041000] usbcore: registered new interface driver usbfs [ 0.042000] usbcore: registered new interface driver hub [ 0.042000] usbcore: registered new device driver usb [ 0.043000] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.044000] Bluetooth: Core ver 2.16 [ 0.044000] NET: Registered protocol family 31 [ 0.045000] Bluetooth: HCI device and connection manager initialized [ 0.045000] Bluetooth: HCI socket layer initialized [ 0.046000] Bluetooth: L2CAP socket layer initialized [ 0.046000] Bluetooth: SCO socket layer initialized [ 0.047000] cfg80211: Calling CRDA to update world regulatory domain [ 0.048000] Switching to clocksource wktmr [ 0.057000] NET: Registered protocol family 2 [ 0.075000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.076000] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.077000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 0.078000] TCP: Hash tables configured (established 16384 bind 16384) [ 0.079000] TCP: reno registered [ 0.080000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.080000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.081000] NET: Registered protocol family 1 [ 0.082000] RPC: Registered named UNIX socket transport module. [ 0.083000] RPC: Registered udp transport module. [ 0.083000] RPC: Registered tcp transport module. [ 0.084000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.087000] NFS: Registering the id_resolver key type [ 0.088000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.090000] msgmni has been set to 612 [ 0.091000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.092000] io scheduler noop registered [ 0.092000] io scheduler cfq registered (default) [ 0.093000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.095000] serial8250.0: ttyS0 at MMIO 0x10406800 (irq = 62) is a 16550A [ 0.095000] console [ttyS0] enabled, bootconsole disabled [ 0.095000] console [ttyS0] enabled, bootconsole disabled [ 0.100000] loop: module loaded [ 0.101000] brcmstb_nand: NAND controller driver is loaded [ 0.102000] tun: Universal TUN/TAP device driver, 1.6 [ 0.102000] tun: (C) 1999-2004 Max Krasnyansky [ 0.225000] bcmgenet: configuring instance #0 for internal PHY [ 0.245000] bcmgenet bcmgenet.0: (unregistered net_device): link down [ 0.246000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.247000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.247000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.279000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300 [ 0.285000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.286000] hub 1-0:1.0: USB hub found [ 0.286000] hub 1-0:1.0: 2 ports detected [ 0.287000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.288000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 0.288000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2 [ 0.289000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400 [ 0.355000] hub 2-0:1.0: USB hub found [ 0.356000] hub 2-0:1.0: 2 ports detected [ 0.356000] Initializing USB Mass Storage driver... [ 0.357000] usbcore: registered new interface driver usb-storage [ 0.358000] USB Mass Storage support registered. [ 0.358000] i2c /dev entries driver [ 0.359000] lirc_dev: IR Remote Control driver registered, major 253 [ 0.359000] usbcore: registered new interface driver btusb [ 0.361000] TCP: cubic registered [ 0.361000] NET: Registered protocol family 10 [ 0.363000] NET: Registered protocol family 17 [ 0.364000] Bluetooth: RFCOMM TTY layer initialized [ 0.364000] Bluetooth: RFCOMM socket layer initialized [ 0.365000] Bluetooth: RFCOMM ver 1.11 [ 0.365000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.366000] Bluetooth: BNEP filters: protocol multicast [ 0.366000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.367000] L2TP core driver, V2.0 [ 0.368000] Registering the dns_resolver key type [ 0.368000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor [ 0.370000] EBI CS2: setting up NAND flash (primary) [ 0.371000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 512MiB 3,3V 8-bit) [ 0.372000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4 [ 0.372000] [ 0.374000] Bad block table found at page 262080, version 0x01 [ 0.375000] Bad block table found at page 262016, version 0x01 [ 0.376000] nand_read_bbt: bad block at 0x000002760000 [ 0.377000] nand_read_bbt: bad block at 0x0000034a0000 [ 0.377000] nand_read_bbt: bad block at 0x00000b940000 [ 0.378000] nand_read_bbt: bad block at 0x00000e220000 [ 0.379000] nand_read_bbt: bad block at 0x000015fe0000 [ 0.380000] Creating 3 MTD partitions on "brcmnand.0": [ 0.381000] 0x000000000000-0x00001f500000 : "rootfs" [ 0.383000] 0x000000000000-0x000020000000 : "entire_device" [ 0.385000] 0x00001f500000-0x00001fa00000 : "kernel" [ 0.386000] EBI CS0: setting up SPI flash [ 0.387000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address [ 0.387000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated [ 0.388000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv [ 0.389000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.603000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.120000] bcmgenet bcmgenet.0: eth0: link up, 100 Mbps, full duplex [ 2.121000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 2.132000] IP-Config: Guessing netmask 255.255.255.0 [ 2.132000] IP-Config: Complete: [ 2.133000] device=eth0, addr=192.168.200.10, mask=255.255.255.0, gw=255.255.255.255 [ 2.134000] host=192.168.200.10, domain=, nis-domain=(none) [ 2.134000] bootserver=255.255.255.255, rootserver=192.168.200.1, rootpath= [ 2.135000] ALSA device list: [ 2.136000] No soundcards found. [ 307.616000] VFS: Unable to mount root fs via NFS, trying floppy. [ 307.617000] VFS: Cannot open root device "nfs" or unknown-block(2,0): error -6 [ 307.618000] Please append a correct "root=" boot option; here are the available partitions: [ 307.619000] 1f00 513024 mtdblock0 (driver?) [ 307.619000] 1f01 524288 mtdblock1 (driver?) [ 307.620000] 1f02 5120 mtdblock2 (driver?) [ 307.621000] 1f03 16384 mtdblock3 (driver?) [ 307.621000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) [ 307.622000] Rebooting in 180 seconds.. [ 307.622000] ------------[ cut here ]------------ [ 307.622000] WARNING: at smp.c:464 smp_call_function_many+0x118/0x3a0() [ 307.622000] Modules linked in: [ 307.622000] Call Trace: [ 307.622000] [<805b24e4>] dump_stack+0x8/0x34 [ 307.622000] [<80022c8c>] warn_slowpath_common+0x78/0xa4 [ 307.622000] [<80022d40>] warn_slowpath_null+0x18/0x24 [ 307.622000] [<80074c60>] smp_call_function_many+0x118/0x3a0 [ 307.622000] [<80074f14>] smp_call_function+0x2c/0x3c [ 307.622000] [<802fd1d4>] brcm_machine_restart+0x10/0x44 [ 307.622000] [<805b26a4>] panic+0x194/0x20c [ 307.622000] [<806defa4>] mount_block_root+0x1e0/0x2a8 [ 307.622000] [<806df19c>] mount_root+0x130/0x15c [ 307.622000] [<806df34c>] prepare_namespace+0x184/0x224 [ 307.622000] [<806dec14>] kernel_init+0x258/0x260 [ 307.622000] [<8000614c>] kernel_thread_helper+0x10/0x18 [ 307.622000] [ 307.622000] ---[ end trace 90a3a22e0854512c ]--- Dreambox DM520 M0CZS L2=1 LLMB=1 BrCfg=E30FB7C6 #@ BCM973625A0 CFE v15.3, Endian Mode: Little Build Date: Thu May 19 18:50:53 2016 (Jann@Cynric) Copyright (C) Broadcom Corporation. Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spare Area Size=16 MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256 CPU speed: 751MHz DDR Frequency: 1061 MHz DDR Mode: DDR3 Total memory(MEMC 0): 512MB MEMC 0 DDR Width: 16 Boot Device: SPI Total flash: 16MB RTS VERSION: rts_hevc10_1067 ETH0_PHY: INT ETH0_MDIO_MODE: 1 ETH0_SPEED: 100 ETH0_PHYADDR: 1 Initializing USB. CFE initialized. ***** DREAMBOX SSBL ***** Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 500ms to cancel Proceeding with autoboot.. You can try aborting with Ctrl+C DM FABTEST CFE starting up Device eth0: hwaddr 00-09-34-FF-00-01, ipaddr 192.168.200.10, mask not set gateway not set, nameserver not set Loader:elf Filesys:raw Dev:flash0.kernel File: Options:bmem=192M@64M console=ttyS0,1000000 root=/dev/nfs nfsroot=192.168.200.1:/srv/nfs/prodtest_dm520 ip=192.168.200.10 Loading: 0x80001000/7448768 0x8071b8c0/240128 Entry address is 0x805af9b0 Closing network eth0 Ethernet link is up: 100 Mbps Full-Duplex Starting program at 0x805af9b0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4-3.9-dm520 (ghost@Client) (gcc version 4.8.1 (GCC) ) #3 SMP Thu May 26 17:47:31 CEST 2016 [ 0.000000] Fetching vars from bootloader... found 13 vars. [ 0.000000] Options: moca=0 sata=0 pcie=0 usb=1 [ 0.000000] Using 512 MB + 0 MB RAM (from CFE) [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a065 (Broadcom BMIPS4380) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] memory: 10000000 @ 20000000 (usable) [ 0.000000] bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00030000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] 0: 0x00020000 -> 0x00030000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81606000 s6336 r8192 d14144 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536 [ 0.000000] Kernel command line: bmem=192M@64M console=ttyS0,1000000 root=/dev/nfs nfsroot=192.168.200.1:/srv/nfs/prodtest_dm520 ip=192.168.200.10 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.000000] Memory: 313536k/524288k available (5874k kernel code, 210752k reserved, 1152k data, 248k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:160 [ 0.000000] Measuring MIPS counter frequency... [ 0.000000] Detected MIPS clock frequency: 751 MHz (375.761 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] Calibrating delay loop... 749.56 BogoMIPS (lpj=374784) [ 0.010000] pid_max: default: 32768 minimum: 301 [ 0.010000] Mount-cache hash table entries: 512 [ 0.011000] Initializing cgroup subsys cpuacct [ 0.012000] Initializing cgroup subsys devices [ 0.012000] Initializing cgroup subsys freezer [ 0.013000] SMP: Booting CPU1... [ 0.017000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.017000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes [ 0.018000] CPU revision is: 0002a065 (Broadcom BMIPS4380) [ 0.018000] FPU revision is: 00130001 [ 0.027000] SMP: CPU1 is running [ 0.027000] Brought up 2 CPUs [ 0.030000] devtmpfs: initialized [ 0.034000] NET: Registered protocol family 16 [ 0.035000] USB0: power enable is active high; overcurrent is active low [ 0.040000] bio: create slab at 0 [ 0.041000] SCSI subsystem initialized [ 0.041000] usbcore: registered new interface driver usbfs [ 0.042000] usbcore: registered new interface driver hub [ 0.042000] usbcore: registered new device driver usb [ 0.043000] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.044000] Bluetooth: Core ver 2.16 [ 0.044000] NET: Registered protocol family 31 [ 0.045000] Bluetooth: HCI device and connection manager initialized [ 0.045000] Bluetooth: HCI socket layer initialized [ 0.046000] Bluetooth: L2CAP socket layer initialized [ 0.046000] Bluetooth: SCO socket layer initialized [ 0.047000] cfg80211: Calling CRDA to update world regulatory domain [ 0.048000] Switching to clocksource wktmr [ 0.056000] NET: Registered protocol family 2 [ 0.073000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.074000] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.076000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 0.077000] TCP: Hash tables configured (established 16384 bind 16384) [ 0.077000] TCP: reno registered [ 0.078000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.078000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.079000] NET: Registered protocol family 1 [ 0.080000] RPC: Registered named UNIX socket transport module. [ 0.081000] RPC: Registered udp transport module. [ 0.082000] RPC: Registered tcp transport module. [ 0.082000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.085000] NFS: Registering the id_resolver key type [ 0.086000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.088000] msgmni has been set to 612 [ 0.089000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.090000] io scheduler noop registered [ 0.091000] io scheduler cfq registered (default) [ 0.091000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.093000] serial8250.0: ttyS0 at MMIO 0x10406800 (irq = 62) is a 16550A [ 0.093000] console [ttyS0] enabled, bootconsole disabled [ 0.093000] console [ttyS0] enabled, bootconsole disabled [ 0.098000] loop: module loaded [ 0.099000] brcmstb_nand: NAND controller driver is loaded [ 0.099000] tun: Universal TUN/TAP device driver, 1.6 [ 0.100000] tun: (C) 1999-2004 Max Krasnyansky [ 0.222000] bcmgenet: configuring instance #0 for internal PHY [ 0.242000] bcmgenet bcmgenet.0: (unregistered net_device): link down [ 0.243000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.244000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.244000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.276000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300 [ 0.282000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.283000] hub 1-0:1.0: USB hub found [ 0.283000] hub 1-0:1.0: 2 ports detected [ 0.284000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.285000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 0.285000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2 [ 0.286000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400 [ 0.352000] hub 2-0:1.0: USB hub found [ 0.352000] hub 2-0:1.0: 2 ports detected [ 0.353000] Initializing USB Mass Storage driver... [ 0.354000] usbcore: registered new interface driver usb-storage [ 0.355000] USB Mass Storage support registered. [ 0.355000] i2c /dev entries driver [ 0.356000] lirc_dev: IR Remote Control driver registered, major 253 [ 0.356000] usbcore: registered new interface driver btusb [ 0.358000] TCP: cubic registered [ 0.358000] NET: Registered protocol family 10 [ 0.360000] NET: Registered protocol family 17 [ 0.360000] Bluetooth: RFCOMM TTY layer initialized [ 0.361000] Bluetooth: RFCOMM socket layer initialized [ 0.362000] Bluetooth: RFCOMM ver 1.11 [ 0.362000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.363000] Bluetooth: BNEP filters: protocol multicast [ 0.363000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.364000] L2TP core driver, V2.0 [ 0.364000] Registering the dns_resolver key type [ 0.365000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor [ 0.367000] EBI CS2: setting up NAND flash (primary) [ 0.368000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 512MiB 3,3V 8-bit) [ 0.369000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4 [ 0.369000] [ 0.371000] Bad block table found at page 262080, version 0x01 [ 0.372000] Bad block table found at page 262016, version 0x01 [ 0.373000] nand_read_bbt: bad block at 0x000002760000 [ 0.374000] nand_read_bbt: bad block at 0x0000034a0000 [ 0.374000] nand_read_bbt: bad block at 0x00000b940000 [ 0.375000] nand_read_bbt: bad block at 0x00000e220000 [ 0.375000] nand_read_bbt: bad block at 0x000015fe0000 [ 0.377000] Creating 3 MTD partitions on "brcmnand.0": [ 0.377000] 0x000000000000-0x00001f500000 : "rootfs" [ 0.379000] 0x000000000000-0x000020000000 : "entire_device" [ 0.381000] 0x00001f500000-0x00001fa00000 : "kernel" [ 0.383000] EBI CS0: setting up SPI flash [ 0.384000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address [ 0.384000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated [ 0.385000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv [ 0.386000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.600000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.112000] bcmgenet bcmgenet.0: eth0: link up, 100 Mbps, full duplex [ 2.112000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 2.123000] IP-Config: Guessing netmask 255.255.255.0 [ 2.123000] IP-Config: Complete: [ 2.124000] device=eth0, addr=192.168.200.10, mask=255.255.255.0, gw=255.255.255.255 [ 2.125000] host=192.168.200.10, domain=, nis-domain=(none) [ 2.125000] bootserver=255.255.255.255, rootserver=192.168.200.1, rootpath= [ 2.126000] ALSA device list: [ 2.127000] No soundcards found. [ 307.616000] VFS: Unable to mount root fs via NFS, trying floppy. [ 307.618000] VFS: Cannot open root device "nfs" or unknown-block(2,0): error -6 [ 307.618000] Please append a correct "root=" boot option; here are the available partitions: [ 307.619000] 1f00 513024 mtdblock0 (driver?) [ 307.620000] 1f01 524288 mtdblock1 (driver?) [ 307.621000] 1f02 5120 mtdblock2 (driver?) [ 307.621000] 1f03 16384 mtdblock3 (driver?) [ 307.622000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) [ 307.623000] Rebooting in 180 seconds..