Hi,

Done... Thank you very much

let's wait and see

I just boot it!
sequence:
power on - red exclamation mark - power off - 1 second - power on

You can post the links - I understand I can upload through network- Correct?

Happy to apply!

Thank you!
Any update about when? (will I have the dream ok for the next week?)

I started for more than 20 times but it always refuses (for now...) I will make new tries

Hi,

I have a new dreambox 900 which refuse to start and to go in rescue mode
when I start it it displays a red exclamation mark. Same when I try to go in rescue

I got the log, please help

CPU 01
Dreambox DM900
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=000003ae(942)
temperature=00006a7a(27258)
PV=00000364(868)
MV=000003ae(942)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 07080cd0
_ebss 0713dd70
_end 0713dd90
HEAP @ 07200000
STACK @ 09300000
ARCH: CONFIG OK
CLR BSS 07080cd0 to 0713dd70 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

,/
,'/___, BOLT v1.18 v1.18 LOCAL BUILD
.'__ ,' (2016-10-31 21:04:46 cynric@cynric-VirtualBox)
/,' Copyright (C) 2016 Broadcom
/'

Board: BCM97252SSFF
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
CS1: NAND: unrecognized ID: 0xffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
card if inited
set pwm to 0/255
disp id 5420
load image
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.941V, T=+28.719C, PV=0.868V, MV=0.942V, FW=30333278 [0.3.2.x]
USB otp=00000040
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
init fp
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
set pwm to 200/255
TPM error. Please contact Dreambox support