Beiträge von stuntman

    Hi all,

    I'm getting white hairs of so many tests...

    Can you please help me how to configure a DM520 with 2 Inverto Unicable II and two satellites ( Hispasat + Hotbird ).

    My installation is more or less like the example Inverto have on their website:



    The signal is ok, it's working perfectly with a low cost receiver or LG TV, I don't even need the power inserter. The lnbs were programmed using satpal for lnb A and lnb B, with the low cost receiver and LG TV it's possible to configure that ( select unicable lnb A Hispasat, lnb B Hotbird ) but in the DM520 and cannot find that option. I cannot say that hispasat lnb is the lnb A and hotbird is lnb B, so I never have signal on lnb B.


    If I configure DM520 connecting just the Hispsat cable to the tuner ( advance/Hispasat/Unicable II ) everything works.

    If I remove the Hispasat cable and use just the Hotbird cable and configure the DM520 tuner advance/Hotbird/Unicable II no signal, I imagine it's because this lnb is programmed as LNB B

    If I connect both satellites and configure it as advance/Hispasat/ lnb 1/Unicable II and advance/Hotbird/lnb2/Unicable II I just have signal on Hispasat.


    Any ideas on how to solve this?

    Thank you

    Hi dre,


    Thanks for answering.


    Well I tried with my DM520 and get the cfe mode at first try, but with dm900 it simply doesn`t enter into cfe mode. I don`t have access through telnet or web interface ( rescue mode ).


    When I try get the receiver in rescue mode it seems everything goes ok, the led starts blinking but when it stops I just have an exclamation point ( ! ) in the display, no ip from DM900. I have a fritzbox with dhcp activated, normally I get for the dm900 the address dm900.fritz.box or for the dm520 dm520.fritz.box.


    This is the log I get:


    CPU 01
    Dreambox DM900
    AVS init...
    AVS init OK
    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
    AVS load_code offset =00051000
    LOADED
    AVS: overtemp mon ON


    single board
    select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
    MEMSYS-STD
    SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
    MCB: FLEX
    AVS start:status=000000ff
    STB: Current voltage=000003a1(929)
    temperature=000051bf(20927)
    PV=0000035b(859)
    MV=000003a1(929)
    AVS FW rev=30333278 [0.3.2.x]
    OK
    DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
    DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
    Sdram Scramble OTP = 0x00000001
    Sdram Scramble OK
    select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
    BFW load mode OTP = 0x0000000f
    bfw_hash_locked = 0x00000000
    BFW key3 OK, BFW load OK
    BFW v2.1.0
    COPY CODE... DONE
    MICH: disable success
    SSBL
    PINMUX
    CACHE FLUSH OK
    MMU ON
    CACHE FLUSH OK
    _fbss 07080cd0
    _ebss 0713dd70
    _end 0713dd90
    HEAP @ 07200000
    STACK @ 09300000
    ARCH: CONFIG OK
    CLR BSS 07080cd0 to 0713dd70 OK
    CLR SRAM OK
    CACHE FLUSH OK
    CPU CLKSET OK
    GO!


    ,/
    ,'/___, BOLT v1.18 v1.18 LOCAL BUILD
    .'__ ,' (2017-03-07 20:27:59 cynric@cynric-VirtualBox)
    /,' Copyright (C) 2017 Broadcom
    /'


    Board: BCM97252SSFF
    SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
    otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
    otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
    CPU: 2x B15 [420f00f3] 1719 MHz
    SCB: 432 MHz
    DDR0 @ 1067MHz, DDR1 @ 1067MHz
    RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
    CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
    CS1: NAND: unrecognized ID: 0x20ffff 0xffffffff
    RTS0: 0x1101004, 256 clients, ok
    RTS1: 0x1181004, 256 clients, ok
    BOX MODE: 5
    card if inited
    set pwm to 0/255
    disp id 0000
    load image
    AVS: park check
    AVS: temperature monitoring enabled
    AVS: STB: V=0.928V, T=+22.388C, PV=0.859V, MV=0.929V, FW=30333278 [0.3.2.x]
    USB otp=00000040
    USB @ 0xf0470200: IPP is active low, IOC is negative polarity
    init fp
    found card in unknown state
    cannot read T1 header
    error in receive
    error during t1 transfer
    cannot read fabca-cert
    retrying.. card if inited
    found card in unknown state
    cannot read T1 header
    error in receive
    error during t1 transfer
    cannot read fabca-cert
    retrying.. card if inited
    found card in unknown state
    cannot read T1 header
    error in receive
    error during t1 transfer
    cannot read fabca-cert
    retrying.. card if inited
    found card in unknown state
    cannot read T1 header
    error in receive
    error during t1 transfer
    cannot read fabca-cert
    retrying.. card if inited
    found card in unknown state
    cannot read T1 header
    error in receive
    error during t1 transfer
    cannot read fabca-cert
    retrying.. card if inited
    set pwm to 200/255
    TPM error. Please contact Dreambox support

    I`m following this to get into cfe bios in a DM900, but I simply can get into cfe. I can get the bootlog.
    Can anyone give some ideas?

    Hi, I`m with a problem with my DM525, it simply doesn`t enter in recovery mode, I already used the option "recovery mode" in the menu, the telnet option and the "manual" mode. It always happens the same thing, it boots the red led stays on, like if it was in recovery mode, but no ip in the tv. Can I update the recovery mode by some how?
    In attached you can find the log.
    Thank you.
    log.txt

    Hi,


    So one more with the same problem...


    No doubts that the DM900 have to be changed?


    Here it is the log:


    CPU 01
    Dreambox DM900
    AVS init...
    AVS init OK
    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
    AVS load_code offset =00051000
    LOADED
    AVS: overtemp mon ON


    single board
    select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
    MEMSYS-STD
    SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
    MCB: FLEX
    AVS start:status=000000ff
    STB: Current voltage=00000397(919)
    temperature=0000ba60(47712)
    PV=00000356(854)
    MV=00000397(919)
    AVS FW rev=30333278 [0.3.2.x]
    OK
    DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
    DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000
    MEMSYS ERROR: 00000001


    eMEMC:
    00000000
    ePHY: 00000000
    eSHMOO: 10000000 00000082 00000000
    CPU 01
    Dreambox DM900
    AVS init...
    AVS init OK
    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a2f2b00
    AVS load_code offset =00051000
    LOADED
    AVS: overtemp mon ON


    single board
    MEMSYS:0000002f
    FATAL ERROR: Boot 2nd image failed

    Keep constantly pushing power while turning on. Wait for the countdown...

    Hi,


    Thanks for the quick reply. I alredy had tried that but instead going to recovery menu it went to the another menu ( AUTOBOOT ).


    But now it`s ok I was able to go to the recovery menu and restore the dreambox.


    Thanks

    Good morning,


    Today i was trying to restore my DM7080 but i can`t access to the boot/recovery menu, i do the normal procedure turn off the receiver, turn on pressing the down button, find the IP and than put it in the browser. But than the browser don`t fnd the page.


    Any ideas how to solve this?


    thanks


    Hello,



    One more with the same problem...



    After a year of development, did not expect that the DMM was not able to fix these bugs on DB 800HD, at this time i`m start wondering if DMM it`s waiting for stock off on the DM 500s/+ and DM600....