Hi,

Oh boy, it seems there are lots of them! As dhwz said it is better these providers follow the DVB standards.

By now i hope you know how to tackle these problems!

There are some typo in last file, please change it with this one!

Hi,

Sorry, i thought they are on the same path 8.0W. Now i changed them to 7.0W but please be aware if somebody is using it as 7.3W in their satellite.xml then the orbpos should be changed to 3527.

Hi,

Now all will work!

Hi,

1- Copy the attached file to /etc/enigma2/ path in your box.

2- Scan each TP with clean before scan active(on).

3- this feature only works on Images based on dreamOS, others like open* do not support it.

I have checked it and confirm that it is functioning.dreambox.de/board/wcf/index.php?attachment/21805/

Hi

If you are using DP Image.

Post

RE: [Solved]TP scan conflict on 7.0E

Hi,
@Ghost, i now confirm that it works after 02-12-2015 update. I have added another ONID/TSID on 26.0E for 11881H and 12284V TPs.
It should be placed under /etc/enigma2 for all dreamboxes.
Thanks.

kamsat10

Dec 3rd 2015

for your orbital position 8W use "3520"

Hi,
If not yet done, you may need this libusbtuner to be installed in your image.

Hello,

Broadcom’s BCM7439 integrates the High Efficiency Video Codec (HEVC) compression standard along with Multimedia over Coax Alliance (MoCA) 2.0 connectivity for cable and satellite video gateways. The BCM7439 also incorporates a feature called Dual Display, which enables presentation of two simultaneous video channels from the same STB via independent HDMI outputs and remote control devices. The BCM7439 is part of Broadcom's complete portfolio of HEVC-enabled devices that allow operators to substantially cut the bandwidth required for video transmission, offer additional channels on IP, cable or satellite networks, and deliver these services to more locations throughout the home on managed or unmanaged devices. 

It seems the SoC has this capability to output to two independent HDMI port but this feature has not been implemented in Dreambox.

Hello,
I reported this issue some times ago, Here , but it seems that you are luckier than me.
I hope there will be a solution for the 2nd cable problem on the rotor with FBC tuners as well.

hi,
This is due to ONID/TSID conflict. Both TPs are using same ONID = 126 and TSID = 30300.
Please put the attached file(unzip it first) in /etc/enigma2 path and with clean before scan option , do manual scan on both tps, provided that you are using the latest image of your box for oe2.0.

@m0rphU
Thanks for your comments.
as matter of fact i also did study the source codes on the git. I believe it is a great flashing tool and could be as a complement to web-interface as Mimisiku mentioned.

Thanks for your reply,
Yes, it is nice to have a plugin for this but it is also quite easy to manage as mentioned above.
It is also strange that this feature was there for several month but no one mentioned it, even no developer would like to comment on it as well!

I reply to myself:
yes it is possible but only in rescue mode which autoflashd daemon is running and the image name should be in this format, "dreambox-image-dm920.tar.xz" for dm920 box.

Hello

autoflashd: a daemon to flash images automatically from any partition called DREAMFLASH

Dose it mean i can flash a corresponding tarball image through a usb stick or sd card, labeled "DREAMFLASH" in normal boot or rescue boot process with my dm920?

@Ghost
Thanks for the reply, i am using unstable dreambox-image 2018-05-14. This problem happens when i go from multistream tp to another tp on another satellite. most of the time from multistream tp to another tp on the same satellite it works and from this stage changing to another tp on another satellite will aslo function and i have sound and picture.
i am using a 8 port diseqc switch which my motorized dished is on port 1 and some other fixed dishes on other ports. if i don't select multistream tp all switching combinations work with no problem.
i will try to install a fresh image with a fresh channel list without switch.

Hello,
With dm920/dvb-s2x fbc/bcm45308x with latest cvs experimental image, tuning to fta multistream 12341 h 30000 s2/8psk stream id=40 pls mode=auto on Astra 4A@4.8E will cause other services on dream with no picture and sound. With a reboot, box functions normaly and if select the multistream service, the same problem will happen again!

Hi,
Thanks, good news.

Hello,
Probably we are talking about the same problem. Please see this thread and let me know about the result with the remedy that i have offered.
BCM45308X 02.09 drivers issue

Hello,
Thank you guys for the contribution. No, i don't use any ci module.
I could improve the signal reception on the a/m fta station by skewing the lnb around 1 deg. and so but could not eliminate the issue totally. For some hd stations that i have this problem with, i have noticed that they are stations which i lose first in bad weather situation, these bring me to claim about lower sensitivity with new bcm7439.ko and probably if one is at the center of the beam could not experience it.
Currently i am using bcm7439.ko of 2018.01.30 with e2-r25 and i have no such issues.
i know it is an ugly workaround and i lose some features but that is the only way to eliminate this problem so far!
It is true that with the new drivers they have gained more things but probably they have sacrificed other things as it is for me.

What i mean is, with this new tuner drivers i have lower sensitivity. If i could increase the signal level, i will get steady image but with former drivers with the same signal level i have good quality image or better sensitivity.