NO need to FOLD the socket legs
can't agree, even with cutted connector there isn't enough room
NO need to FOLD the socket legs
can't agree, even with cutted connector there isn't enough room
will start by mistakes:
1. in first attempt i had chosen Arctic F9 PWM -
it looks extremely same to Arctic F9 TC,
but were so loud - i were able hear it from ~4 meters and from 2 with added resistor
2. this mistake isn't made by me,
i can't even describe my disappointment about place where socket is located
installation:
fold the socket legs
cut connector body
add two layers of tape on connector
and two layers of tape on HDD/SSD bay
add small distancer
use screw with flat head
i skipped such screw at all in next boxes
connect Arctic F9 TC to resistor and place it little angled on the radiatorbit
fix cooler by small piece of black tape
bedroom edition
hide HDDD/SSD bay
TC means Temperature Controlled
2x Si2169D, ie the multistream triple tuner.
you may not even expect support
To me, that just sounds like the tuner was just broken.
Alles anzeigen... Si2169D, tested 6 ~ 8 pieces -
when tuner A2 starts to use signal then tuner A1 immediately has huge signal drop
while same cables works well in A1 and B1/B2 or A2 and B1/B2 combinations
problem is long time known
i haven't met any working Si2169D, tested 6~8 pieces,
when tuner A2 starts to use signal then tuner A1 immediately has huge signal drop
problem is long time known
Triple Tuner Si2169D tuners independence problem
all what Dream Property support can do,
is give false promises, close ticket without answer or ignore it
You are lucky!
still waiting solution for
Triple Tuner Si2169D tuners independence problem
i'm not that young to believe in Christmas miracle
dass die Channel +/- Tasten funktionieren.
THANKS, that works! but title stays from firstly selected service
similar problem with Triple Tuner
THANKS!
CH -/+ works only once, tested with dm8000
on the evening will test with dm920
Note 10+ Android 9
if channel title's rectangle and other screen can't be separated
then split single touch area it to three invisible touch areas -
<< previous / blank area / stream / blank area / next >>
I agree that this should go on signal page, but where? Keep in mind this has to be buttons with translatable text. End result would probably be ugly.
just idea, by swipe service title rectangle
but also `CH-` and `CH+` must be obvious for most of users
using this app at least three times a year,
would like see buttons CH- and CH+ directly in the signal screen
ZitatThere is now a new ticket system at the following address:
have opened Ticket# 512566:
and there is answer:
after which ticked were marked as closed
what is going on?
worked well in 0E2.0 but it is not launching my script in 0E2.6 DE. Any help please?
few useful posts about required changes in the scripts:
solved partly:
1. video without audio - SOLVED
2. audio without video - SOLVED
3. interrupted recordings were caused Twin tuners independence problem,
it's still there couple of years and looks like solution isn't planned at all
i started separate tread:
well, i have measured also ohms
`3+sp` means cable_3 had two way splitter to able leave one free end for temporary guest boxes
after remove splitter, situation improved, but still abnormal
=== Cable_3 Tuner_A1 ===
=== Cable_1 Tuner_A2 ===
ok main tuner A1 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX (signal drops from 13.75 to 11.75dB)
OK PiP tuner A2 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13
ok main tuner A1 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13 (signal drops from 13.25 to 9.25dB)
OK PiP tuner A2 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX
ok main tuner A1 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13 (signal drops from 13.25 to 8.25dB)
OK PiP tuner A2 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD
ok main tuner A1 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13 (signal drops from 13.25 to 7.00dB)
OK PiP tuner A2 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC
nok main tuner A1 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX (signal drops from 13.50 to 3.75dB)
OK PiP tuner A2 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD
ok main tuner A1 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX (signal drops from 13.50 to 8.00dB)
OK PiP tuner A2 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC
ok main tuner A1 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD (signal drops from 16.75 to 9.25dB)
OK PiP tuner A2 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC
NOK main tuner A1 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC (signal drops from 13.50 to 0.00dB)
OK PiP tuner A2 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD
NOK - no picture at all
nok - huge pixelation
why problem isn't gone?
resistance of the cable_3 is hugely improved and became even better than cable_1
configuration not simple at all,
most popular LNBs are Octo, which are cascaded through 4x1 switch(protocol 1.0) and 1x10 some 1x8 (protocol 1.1)
[User = '15731'] dhwz [/ user]
1. that are so sad news, problem long time known and no solution
2. till now, i thought signals under 10dB can be defined as weak.
most of 19E are between 11 and 15dB, just few transponders are under 10
and 36E have between 12 and 17dB
p.s.
but THANKS for link!
also no problems when connected two identical cables to same Si2169D
config.Nims.0.configMode=multi
config.Nims.0.multiType=1
config.Nims.0.cable.configMode=nothing
config.Nims.0.terrest.configMode=enabled
config.Nims.0.terrest.provider=2
config.Nims.0.terrest.use5V=false
config.Nims.0.sat.configMode=nothing
config.Nims.1.configMode=multi
config.Nims.1.multiType=1
config.Nims.1.cable.configMode=nothing
config.Nims.1.terrest.configMode=enabled
config.Nims.1.terrest.provider=2
config.Nims.1.terrest.use5V=false
config.Nims.1.sat.configMode=nothing
config.Nims.2.configMode=multi
config.Nims.2.multiType=1
config.Nims.2.cable.configMode=nothing
config.Nims.2.terrest.configMode=enabled
config.Nims.2.terrest.provider=2
config.Nims.2.terrest.use5V=false
config.Nims.2.sat.configMode=advanced
config.Nims.2.advanced.sats=130
config.Nims.2.advanced.sat.192.lnb=1
config.Nims.2.advanced.sat.130.lnb=2
config.Nims.2.advanced.sat.360.lnb=3
config.Nims.2.advanced.lnb.1.diseqcMode=1_1
config.Nims.2.advanced.lnb.1.commitedDiseqcCommand=AA
config.Nims.2.advanced.lnb.1.uncommittedDiseqcCommand=1
config.Nims.2.advanced.lnb.1.commandOrder=cut
config.Nims.2.advanced.lnb.2.diseqcMode=1_1
config.Nims.2.advanced.lnb.2.commitedDiseqcCommand=AB
config.Nims.2.advanced.lnb.2.uncommittedDiseqcCommand=1
config.Nims.2.advanced.lnb.2.commandOrder=cut
config.Nims.2.advanced.lnb.3.diseqcMode=1_1
config.Nims.2.advanced.lnb.3.commitedDiseqcCommand=AA
config.Nims.2.advanced.lnb.3.uncommittedDiseqcCommand=3
config.Nims.2.advanced.lnb.3.commandOrder=cut
config.Nims.2.advanced.lnb.3.lof=user_defined
config.Nims.2.advanced.lnb.3.threshold=11600
config.Nims.2.advanced.lnb.3.lofh=10750
config.Nims.2.advanced.lnb.3.lofl=10750
config.Nims.3.configMode=multi
config.Nims.3.multiType=1
config.Nims.3.cable.configMode=nothing
config.Nims.3.terrest.configMode=enabled
config.Nims.3.terrest.provider=2
config.Nims.3.terrest.use5V=false
config.Nims.3.sat.configMode=advanced
config.Nims.3.advanced.sats=130
config.Nims.3.advanced.sat.192.lnb=1
config.Nims.3.advanced.sat.130.lnb=2
config.Nims.3.advanced.sat.360.lnb=3
config.Nims.3.advanced.lnb.1.diseqcMode=1_1
config.Nims.3.advanced.lnb.1.commitedDiseqcCommand=AA
config.Nims.3.advanced.lnb.1.uncommittedDiseqcCommand=1
config.Nims.3.advanced.lnb.1.commandOrder=cut
config.Nims.3.advanced.lnb.2.diseqcMode=1_1
config.Nims.3.advanced.lnb.2.commitedDiseqcCommand=AB
config.Nims.3.advanced.lnb.2.uncommittedDiseqcCommand=1
config.Nims.3.advanced.lnb.2.commandOrder=cut
config.Nims.3.advanced.lnb.3.diseqcMode=1_1
config.Nims.3.advanced.lnb.3.commitedDiseqcCommand=AA
config.Nims.3.advanced.lnb.3.uncommittedDiseqcCommand=3
config.Nims.3.advanced.lnb.3.commandOrder=cut
config.Nims.3.advanced.lnb.3.lof=user_defined
config.Nims.3.advanced.lnb.3.threshold=11600
config.Nims.3.advanced.lnb.3.lofh=10750
config.Nims.3.advanced.lnb.3.lofl=10750
Alles anzeigen
=== Cable_1 Tuner_B1 ===
=== Cable_2 Tuner_B2 ===
OK main tuner B1 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX
OK PiP tuner B2 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13
OK main tuner B1 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13
OK PiP tuner B2 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX
OK main tuner B1 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13
OK PiP tuner B2 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD
OK main tuner B1 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13
OK PiP tuner B2 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC
OK main tuner B1 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX
OK PiP tuner B2 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD
OK main tuner B1 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX
OK PiP tuner B2 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC
OK PiP tuner B1 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD
OK PiP tuner B2 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC
OK PiP tuner B1 36E 12.341 H 1_0_16_451_B_70_1680000_0_0_0 CTC
OK PiP tuner B2 36E 12.015 V 1_0_19_89F_16_70_1680000_0_0_0 THT HD
what logically cancels idea about `Internal Loop-Through`,
can't believe option `Equal-To`, also previously used, can be guilty, but what else..
p.s.
system log is saved, ask if needed
that also isn't power supply problem, measured voltage on cable_3:
Cable_3 A1 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX
signal 13.0dB while alone on main screen
voltage on cable_3: 17.8v
signal dropps to 5.75db immediatly after activated PiP
Cable_1 A2 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13
voltage on cable_3: 17.7v
Cable_3 A1 19E 10.876 V 1_0_1_7790_424_1_C00000_0_0_0 CALLE 13
signal 13.0dB while alone on main screen
voltage on cable_3: 12.8v
signal dropps to 0.00db immediatly after activated PiP
Cable_1 A2 19E 10.744 H 1_0_1_7035_41B_1_C00000_0_0_0 PHOENIX
voltage on cable_3: 12.8v