Use the board search above with MEMSYS ERROR,
and have fun while reading.
than k you for your hint 
I have actually read this before I asked here
i have even contacted Dreambox Germany but no response from them yet 
seem Dreambox is not as it was once upon time
i Understand and I thank you for trying to help me out and appreciate your replay.
I just can't understand for my own purposes how can a box that works normally go so wrong just buy programming , and I can assure you that image flashing whent smooth and everything was fine before:
i gett it that there is a bad memory, but must be a explanation, I know Dreambox would not tell us end users what is the problem, but as I read both here in this forum and many other places this is a know problem for many users
I started with Dreambox since early days and have programeed all the DM models they have come with, but have seen this kind of problem with the lates models
anyway it is just for me knowledge for my own understanding of things and why they go wrong
thank you for your help
thank you for your answer.
for me is a bitt of a mistery that a box can break down after software install, even when the hole process gets done 100% correct and then after it does not boot anymore.
it can't be hardware problem as the last box was working fine before update, then I update the image via web , install goes correctly and 100% then just reboot the box, after is just dead and not working anymore
anyway I am not a engineer nor am I a programer but logically this sound like there is some problem with software then hardware.
thanks for any replays
Hi to all from a new member
I need some help with some problems I have with 2 off dm 900 and 1 dm 920
from 1 dm900 I get this from putty logg
CPU 01
Dreambox DM900
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000398(920)
temperature=00007f67(32615)
PV=00000355(853)
MV=00000398(920)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000
MEMSYS ERROR: 00000001
eMEMC:
00000000
e
PHY: 00000000
eSHMOO: 10000000 00000082 00000000
CPU 01
Dreambox DM900
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a2f2b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
MEMSYS:0000002f
FATAL ERROR: Boot 2nd image failed
the second dm900 some times it starts and some times it just does not, I have plashed image from the update site but still the box does not work anymore now
the image update was Donne via web update / browser, now even this box is dead and does not work anymore.
DM 920 from telnet I gett this message
CPU 01
Dreambox DM920
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000388(904)
temperature=000064c5(25797)
PV=00000349(841)
MV=00000388(904)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000
MEMSYS ERROR: 00000001
eMEMC:
00000000
ePHY: 00000000
eSHMOO: 10400000 00000082 00000000
CPU 01
Dreambox DM920
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a2f2b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
MEMSYS:0000002f
FATAL ERROR: Boot 2nd image failed
I have been reading a bit up and down this board but cannot understand that the boxes just dies sunndendly
like one of the boxes was fine in the evening and next morning was dead. and the other 2 boxes died after image update from dreamboxupdate
the update process was OK, all the way, and im not a beginner in the DM world have programmed many boxes and have owned all the boxes from DM since the first Dreambox come out
is there anything I can do my elf to fix the boxes or do I need to send them back to Germany for a fix, is there any explanation why this happens to this boxes.
there must be a problem with SW or HW that this just dies out
