Beiträge von Tom2018
-
-
-
-
Nein. ich weiss einfach nicht wo ich den rescue-loader.bin herholen soll.
BOLT> PumpKIN.exe
Invalid command: "PumpKIN.exe"
Available commands: usb, sha, rpmb, crc, uncache, memwrap, dt, time, info, set, loop, reboot, dir, macprog, led, mon, card, display, erase, gisb, rts, setboard, boards, flash, memtest, t, f, e, d, u, batch, go, load, save, boot, mii, ephycfg, ttcp, tcp, rlogin, ping, ifconfig, sleep, waitusb, show, testenv, incenv, unsetenv, printenv, setenv, help
-
-
soweit bin ich nun.
*** command status = -1
BOLT> ifconfig eth0 -auto
100 Mbps Full-Duplex
Device eth0: hwaddr 00-09-34-40-1F-81, ipaddr 192.168.2.11, mask 255.255.255.0
gateway 192.168.2.1, nameserver 192.168.2.1, domain fritz.box
DHCP server 192.168.2.1, DHCP server MAC CC-CE-1E-A4-44-C7
*** command status = 0
BOLT> boot -tftp -elf 192.168.2.11:rescue-dm900.bin
Loader:elf Filesys:tftp Dev:eth0 File:192.168.2.11:rescue-dm900.bin Options:(null)
Could not load rescue-dm900.bin: File not found
*** command status = -18
BOLT> boot -tftp tftp-192.168.2.11:rescue-dm900.bin
Loader:zimg Filesys:tftp Dev:eth0 File:tftp-192.168.2.11:rescue-dm900.bin Options:(null)
Could not load rescue-dm900.bin: Host name unknown
*** command status = -20
BOLT> boot -tftp -elf192.168.2.11:rescue-dm900.bin
Invalid switch: -elf192.168.2.11:rescue-dm900.bin
*** command status = -8
BOLT>
Nur was muss ich dann tun?
-
-
-
-
Hier der Bootlog:
CPU 01
Dreambox DM900
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000388(904)
temperature=0000e06c(57452)
PV=0000034a(842)
MV=0000038a(906)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 07080cd0
_ebss 0713dd70
_end 0713dd90
HEAP @ 07200000
STACK @ 09300000
ARCH: CONFIG OK
CLR BSS 07080cd0 to 0713dd70 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
,/
,'/___, BOLT v1.18 v1.18 LOCAL BUILD
.'__ ,' (2017-03-07 20:27:59 cynric@cynric-VirtualBox)
/,' Copyright (C) 2017 Broadcom
/'
Board: BCM97252SSFF
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
CS1: NAND: unrecognized ID: 0x20ffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
card if inited
set pwm to 0/255
disp id 0000
load image
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.904V, T=+58.913C, PV=0.842V, MV=0.906V, FW=30333278 [0.3.2.x]
USB otp=00000040
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
init fp
found card in unknown state
ca valid!
set pwm to 200/255
Normal bootup
Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:(null)
Reading 4305120 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7728000)
32 bit boot...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14-1.17-dm920 (oe-user@oe-host) (gcc version 6.3.0 (GCC) ) #1 SMP Tue May 22 18:59:20 UTC 2018
[ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: BCM97252SSFF
[ 0.000000] moving dtb from 0x0000000007728000 to 0x000000000085bb88
[ 0.000000] bmem: Reserved 640 MiB at 0x0000000018000000
[ 0.000000] bmem: Reserved 384 MiB at 0x0000000080000000
[ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] MCP: Enabling write pairing
[ 0.000000] PERCPU: Embedded 8 pages/cpu @cdfc0000 s8384 r8192 d16192 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523776
[ 0.000000] Kernel command line: bmem=640M@384M bmem=384M@2048M console=ttyS0,1000000 root=/dev/mmcblk0p2 rootwait rootfstype=ext4 coherent_pool=2M
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 1006760K/2097152K available (6197K kernel code, 230K rwdata, 1636K rodata, 244K init, 208K bss, 1074008K reserved, 16384K cma-reserved, 786428K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07ae758 (7834 kB)
[ 0.000000] .init : 0xc07af000 - 0xc07ec0c0 ( 245 kB)
[ 0.000000] .data : 0xc07ee000 - 0xc0827ae0 ( 231 kB)
[ 0.000000] .bss : 0xc0827ae8 - 0xc085bb88 ( 209 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
[ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[ 0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
[ 0.000010] Switching to timer-based delay loop
[ 0.000232] Console: colour dummy device 80x30
[ 0.000252] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[ 0.000262] pid_max: default: 32768 minimum: 301
[ 0.000357] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000362] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.005809] Initializing cgroup subsys devices
[ 0.005823] Initializing cgroup subsys freezer
[ 0.005830] Initializing cgroup subsys net_cls
[ 0.005857] CPU: Testing write buffer coherency: ok
[ 0.006078] CPU0: update cpu_power 1024
[ 0.006083] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.006131] Setting up static identity map for 0x5ea228 - 0x5ea280
[ 0.007347] CPU1: Booted secondary processor
[ 0.007366] CPU1: update cpu_power 1024
[ 0.007368] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.007437] Brought up 2 CPUs
[ 0.007448] SMP: Total of 2 processors activated (108.00 BogoMIPS).
[ 0.007453] CPU: All CPU(s) started in SVC mode.
[ 0.007840] devtmpfs: initialized
[ 0.011267] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[ 0.011816] regulator-dummy: no parameters
[ 0.011996] NET: Registered protocol family 16
[ 0.012947] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.013147] cpuidle: using governor ladder
[ 0.013152] cpuidle: using governor menu
[ 0.014276] irq: no irq domain found for /rdb/interrupt-controller@f040a700 !
[ 0.014360] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.016024] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] registered
[ 0.016097] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
[ 0.016177] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
[ 0.016241] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
[ 0.016303] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
[ 0.016370] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
[ 0.016437] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
[ 0.016500] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
[ 0.016562] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
[ 0.016631] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
[ 0.016698] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
[ 0.016761] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
[ 0.016823] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
[ 0.016888] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
[ 0.017201] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.017425] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[ 0.021815] bio: create slab <bio-0> at 0
[ 0.022108] brcmstb-gpio f040a600.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
[ 0.022137] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
[ 0.022178] brcmstb-gpio f0417400.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
[ 0.022192] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
[ 0.022538] SCSI subsystem initialized
[ 0.022759] usbcore: registered new interface driver usbfs
[ 0.022789] usbcore: registered new interface driver hub
[ 0.022848] usbcore: registered new device driver usb
[ 0.022887] media: Linux media interface: v0.10
[ 0.022910] Linux video capture interface: v2.00
[ 0.022946] pps_core: LinuxPPS API ver. 1 registered
[ 0.022950] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.022961] PTP clock support registered
[ 0.023197] Advanced Linux Sound Architecture Driver Initialized.
[ 0.023490] Bluetooth: Core ver 2.18
[ 0.023506] NET: Registered protocol family 31
[ 0.023510] Bluetooth: HCI device and connection manager initialized
[ 0.023518] Bluetooth: HCI socket layer initialized
[ 0.023524] Bluetooth: L2CAP socket layer initialized
[ 0.023531] Bluetooth: SCO socket layer initialized
[ 0.023798] cfg80211: Calling CRDA to update world regulatory domain
[ 0.024057] Switched to clocksource arch_sys_counter
[ 0.028436] thermal thermal_zone0: failed to read out thermal zone 0
[ 0.028522] NET: Registered protocol family 2
[ 0.028934] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.028949] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.028971] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.029005] TCP: reno registered
[ 0.029012] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.029024] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.029155] NET: Registered protocol family 1
[ 0.029385] RPC: Registered named UNIX socket transport module.
[ 0.029390] RPC: Registered udp transport module.
[ 0.029393] RPC: Registered tcp transport module.
[ 0.029396] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.030007] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.030356] bounce pool size: 64 pages
[ 0.030871] NFS: Registering the id_resolver key type
[ 0.030916] Key type id_resolver registered
[ 0.030920] Key type id_legacy registered
[ 0.030930] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.031078] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 0.031376] msgmni has been set to 462
[ 0.032188] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.032196] io scheduler noop registered
[ 0.032211] io scheduler cfq registered (default)
[ 0.032428] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
[ 0.032715] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
[ 0.098342] brcmstb_memc f1102000.memc-ddr: registered
[ 0.098369] brcmstb_memc f1182000.memc-ddr: registered
[ 0.098554] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.099327] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
[ 0.196004] console [ttyS0] enabled
[ 0.197225] loop: module loaded
[ 0.197866] ahci brcmstb-ahci.0: can't get clock
[ 0.198484] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[ 0.210074] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.211073] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part
[ 0.213702] scsi0 : ahci_platform
[ 0.214334] scsi1 : ahci_platform
[ 0.214841] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
[ 0.215758] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
[ 0.217195] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[ 0.217966] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[ 0.219130] m25p80 spi32766.0: found mx25l25635e, expected m25p80
[ 0.219842] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address
[ 0.220579] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
[ 0.221224] 5 ofpart partitions found on MTD device spi32766.0
[ 0.221894] Creating 5 MTD partitions on "spi32766.0":
[ 0.222494] 0x000000000000-0x000000200000 : "flash0.bolt"
[ 0.223617] 0x000000200000-0x000000220000 : "flash0.nvram"
[ 0.224678] 0x000000220000-0x000000240000 : "flash0.devtree"
[ 0.225727] 0x000000240000-0x000001000000 : "flash0.recovery"
[ 0.226798] 0x000000000000-0x000002000000 : "flash0"
[ 0.228080] libphy: Fixed MDIO Bus: probed
[ 0.228897] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[ 0.242061] libphy: bcmgenet MII bus: probed
[ 0.262939] xhci-brcm: xHCI BRCM driver
[ 0.263465] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 0.264134] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[ 0.265325] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
[ 0.266169] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.266949] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.267787] usb usb1: Product: xHCI Host Controller
[ 0.268354] usb usb1: Manufacturer: Linux 3.14-1.17-dm920 xhci-hcd
[ 0.269075] usb usb1: SerialNumber: f0471000.xhci_v2
[ 0.269961] hub 1-0:1.0: USB hub found
[ 0.270425] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 0.271360] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 0.272016] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[ 0.273040] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.273827] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.274660] usb usb2: Product: xHCI Host Controller
[ 0.275233] usb usb2: Manufacturer: Linux 3.14-1.17-dm920 xhci-hcd
[ 0.275943] usb usb2: SerialNumber: f0471000.xhci_v2
[ 0.276794] hub 2-0:1.0: USB hub found
[ 0.277253] hub 2-0:1.0: 2 ports detected
[ 0.278025] ehci-brcm: EHCI BRCM driver
[ 0.278546] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[ 0.279218] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
] 0.290228] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
0.296068] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.296880] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.297668] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.298502] usb usb3: Product: EHCI Host Controller
[ 0.299069] usb usb3: Manufacturer: Linux 3.14-1.17-dm920 ehci_hcd
[ 0.299779] usb usb3: SerialNumber: f0470300.ehci_v2
[ 0.300637] hub 3-0:1.0: USB hub found
[ 0.301096] hub 3-0:1.0: 1 port detected
[ 0.301737] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[ 0.302405] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
c 0.313407] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
0.320063] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.320863] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.321649] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.322483] usb usb4: Product: EHCI Host Controller
[ 0.323045] usb usb4: Manufacturer: Linux 3.14-1.17-dm920 ehci_hcd
[ 0.323760] usb usb4: SerialNumber: f0470500.ehci_v2
[ 0.324589] hub 4-0:1.0: USB hub found
[ 0.325040] hub 4-0:1.0: 1 port detected
[ 0.325746] ohci-brcm: OHCI BRCM driver
[ 0.326252] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[ 0.326910] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
[ 0.327073] ata1: SATA link down (SStatus 0 SControl 300)
[ 0.328448] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
0.384180] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.384961] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.385794] usb usb5: Product: BRCM OHCI controller
[ 0.386362] usb usb5: Manufacturer: Linux 3.14-1.17-dm920 ohci_hcd
[ 0.387076] usb usb5: SerialNumber: f0470400.ohci_v2
[ 0.387940] hub 5-0:1.0: USB hub found
[ 0.388413] hub 5-0:1.0: 1 port detected
[ 0.389085] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[ 0.389746] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
[ 0.390668] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
9 0.439066] ata2: SATA link down (SStatus 0 SControl 300)
c 0.446162] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.446942] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.447777] usb usb6: Product: BRCM OHCI controller
[ 0.448344] usb usb6: Manufacturer: Linux 3.14-1.17-dm920 ohci_hcd
[ 0.449059] usb usb6: SerialNumber: f0470600.ohci_v2
[ 0.449887] hub 6-0:1.0: USB hub found
[ 0.450353] hub 6-0:1.0: 1 port detected
[ 0.451068] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.451818] ehci-pci: EHCI PCI platform driver
[ 0.452375] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.453095] ohci-pci: OHCI PCI platform driver
[ 0.453722] usbcore: registered new interface driver usb-storage
[ 0.454458] i2c /dev entries driver
[ 0.454901] lirc_dev: IR Remote Control driver registered, major 250
[ 0.455956] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[ 0.456946] usbcore: registered new interface driver btusb
[ 0.457638] cpufreq_cpu0: failed to get cpu0 regulator: -19
0 0.458450] brcmstb-cpufreq: probe of f03e257c.cpu-clk-div failed with error -17
[ 0.459381] sdhci: Secure Digital Host Controller Interface driver
[ 0.460097] sdhci: Copyright(c) Pierre Ossman
[ 0.460597] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.462348] mmc0: no vqmmc regulator found
[ 0.462822] mmc0: no vmmc regulator found
e 0.493068] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
[ 0.494979] mmc1: no vqmmc regulator found
[ 0.495458] mmc1: no vmmc regulator found
0.526062] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[ 0.527015] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.527726] usbcore: registered new interface driver usbhid
[ 0.528374] usbhid: USB HID core driver
[ 0.530801] TCP: cubic registered
[ 0.531806] NET: Registered protocol family 10
o 0.532795] NET: Registered protocol family 17
0.533537] Bluetooth: RFCOMM TTY layer initialized
S 0.534120] Bluetooth: RFCOMM socket layer initialized
[ 0.534712] Bluetooth: RFCOMM ver 1.11
[ 0.535154] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.535765] Bluetooth: BNEP filters: protocol multicast
[ 0.536373] Bluetooth: BNEP socket layer initialized
[ 0.536944] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.537636] Bluetooth: HIDP socket layer initialized
[ 0.538254] l2tp_core: L2TP core driver, V2.0
[ 0.538772] Key type dns_resolver registered
[ 0.539344] Registering SWP/SWPB emulation handler
[ 0.540168] regulator-dummy: disabling
[ 0.542846] ALSA device list:
[ 0.543201] No soundcards found.
[ 0.543816] Waiting for root device /dev/mmcblk0p2...
i 0.595703] mmc1: BKOPS_EN bit is not set
s 0.602503] mmc1: new high speed MMC card at address 0001
[ 0.603361] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
[ 0.603986] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
[ 0.604783] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
[ 0.605550] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
0.609291] mmcblk0: p1 p2 p3
3 0.611818] mmcblk0boot1: unknown partition table
[ 0.612862] mmcblk0boot0: unknown partition table
a 0.650117] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 0.651085] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 0.652664] devtmpfs: mounted
2INIT: persion 2.88 booting5
5tarting fake hwclock: loading system time.
cat Jun 2 17:27:36 UTC 2018
p 0.839780] fuse init (API version 7.22)
i 1.091036] stb_core: module license 'Proprietary' taints kernel.
[ 1.091771] Disabling lock debugging due to kernel taint
M 1.141296] input: dreambox remote control (native) as /devices/virtual/input/input0
o 1.145706] input: dreambox advanced remote control (native) as /devices/virtual/input/input1
- 1.166033] random: nonblocking pool is initialized
0 1.365149] bcm7439: xvd 20160630, vdc 20160630, rap 20160630, xpt 20160630, driver version 20180514-dm920
2 2.831139] 2:830085785 UARTC: cannot reset tpm
] 2.842173] 2:841122404 SMCB: controller reset timed out
[ 2.843212] TPM validation failed.
d 2.845512] register adapter
2.847755] register adapter
- 2.851379] register adapter
2.854784] register adapter
b 2.860035] register adapter
s 2.863726] fpga init
2.964634] fpga no init ack!
[ 2.965227] fe_common: retrying i2c transfer at adapter 2 (0x9)
[ 2.966118] fe_common: retrying i2c transfer at adapter 2 (0x9)
[ 2.967006] fe_common: retrying i2c transfer at adapter 2 (0x9)
r 2.967906] fe_common: retrying i2c transfer at adapter 2 (0x9)
2 2.968812] fe_common: retrying i2c transfer at adapter 2 (0x9)
2.969705] fe_common: retrying i2c transfer at adapter 2 (0x9)
h 2.970594] fe_common: retrying i2c transfer at adapter 2 (0x9)
d 2.971719] fe_common: retrying i2c transfer at adapter 2 (0x9)
0 2.972619] fe_common: retrying i2c transfer at adapter 2 (0x9)
1 2.973510] fe_common: retrying i2c transfer at adapter 2 (0x9)
[ 2.974208] ------------[ cut here ]------------
, 2.974755] WARNING: CPU: 0 PID: 154 at /home/ghost/hdb/dreambox/treiber-cvs/dm8000/stb/frontend.c:33 fe_i2c_transfer+0x64/0x6c [stb_core]()
[ 2.976205] Modules linked in: bcm7439(PO+) si2183(PO) alps_bsbe2(PO) alps_bsbe1(O) bcm4506(PO) si2166b(PO) cxd1981(PO) cu1216mk3(PO) alps_bsbe1_c01a(PO) lnb_ctrl(PO) tu1216(O) dreambox_rc2(PO) lcd(PO) stb_core(PO) fuse
[ 2.978528] CPU: 0 PID: 154 Comm: modprobe Tainted: P O 3.14-1.17-dm920 #1
[ 2.979432] [<c0014e14>] (unwind_backtrace) from [<c00111dc>] (show_stack+0x10/0x14)
[ 2.980328] [<c00111dc>] (show_stack) from [<c05e4bc4>] (dump_stack+0x84/0x98)
[ 2.981163] [<c05e4bc4>] (dump_stack) from [<c001eda0>] (warn_slowpath_common+0x6c/0x88)
[ 2.982093] [<c001eda0>] (warn_slowpath_common) from [<c001ee58>] (warn_slowpath_null+0x1c/0x24)
[ 2.983104] [<c001ee58>] (warn_slowpath_null) from [<bf01a560>] (fe_i2c_transfer+0x64/0x6c [stb_core])
[ 2.984177] [<bf01a560>] (fe_i2c_transfer [stb_core]) from [<bf01a5c8>] (fe_read_adap+0x60/0x98 [stb_core])
[ 2.985442] [<bf01a5c8>] (fe_read_adap [stb_core]) from [<bf34abd4>] (fpga_readreg+0x28/0x54 [bcm7439])
[ 2.986819] [<bf34abd4>] (fpga_readreg [bcm7439]) from [<bf7cd0d0>] (bcm_fpga_init+0x58/0x16c [bcm7439])
[ 2.988069] [<bf7cd0d0>] (bcm_fpga_init [bcm7439]) from [<bf7cc080>] (bcm_base_fpga_init+0x10/0x54 [bcm7439])
[ 2.989364] [<bf7cc080>] (bcm_base_fpga_init [bcm7439]) from [<bf7cc30c>] (init_module+0x90/0x11c [bcm7439])
[ 2.990573] [<bf7cc30c>] (init_module [bcm7439]) from [<c0008968>] (do_one_initcall+0xf8/0x154)
[ 2.991576] [<c0008968>] (do_one_initcall) from [<c007fa74>] (load_module+0x1c28/0x1ed8)
[ 2.992507] [<c007fa74>] (load_module) from [<c007feac>] (SyS_finit_module+0x80/0x90)
[ 2.993409] [<c007feac>] (SyS_finit_module) from [<c000e2e0>] (ret_fast_syscall+0x0/0x38)
[ 2.994372] ---[ end trace c367d1dd624e97a6 ]---
[ 2.994905] fe: read ret=-110
[ 2.995256] fpga_readreg ff failed
[ 2.995651] Kernel panic - not syncing: fpga is not there!
[ 2.995651]
[ 2.996451] CPU: 0 PID: 154 Comm: modprobe Tainted: P W O 3.14-1.17-dm920 #1
[ 2.997345] [<c0014e14>] (unwind_backtrace) from [<c00111dc>] (show_stack+0x10/0x14)
[ 2.998239] [<c00111dc>] (show_stack) from [<c05e4bc4>] (dump_stack+0x84/0x98)
[ 2.999070] [<c05e4bc4>] (dump_stack) from [<c05e3f18>] (panic+0x9c/0x1e8)
[ 2.999974] [<c05e3f18>] (panic) from [<bf7cd0e4>] (bcm_fpga_init+0x6c/0x16c [bcm7439])
[ 3.001055] [<bf7cd0e4>] (bcm_fpga_init [bcm7439]) from [<bf7cc080>] (bcm_base_fpga_init+0x10/0x54 [bcm7439])
[ 3.002349] [<bf7cc080>] (bcm_base_fpga_init [bcm7439]) from [<bf7cc30c>] (init_module+0x90/0x11c [bcm7439])
[ 3.003556] [<bf7cc30c>] (init_module [bcm7439]) from [<c0008968>] (do_one_initcall+0xf8/0x154)
[ 3.004555] [<c0008968>] (do_one_initcall) from [<c007fa74>] (load_module+0x1c28/0x1ed8)
[ 3.005486] [<c007fa74>] (load_module) from [<c007feac>] (SyS_finit_module+0x80/0x90)
[ 3.006386] [<c007feac>] (SyS_finit_module) from [<c000e2e0>] (ret_fast_syscall+0x0/0x38)
[ 3.007326] CPU1: stopping
[ 3.007643] CPU: 1 PID: 0 Comm: swapper/1 Tainted: P W O 3.14-1.17-dm920 #1
[ 3.008527] [<c0014e14>] (unwind_backtrace) from [<c00111dc>] (show_stack+0x10/0x14)
[ 3.009419] [<c00111dc>] (show_stack) from [<c05e4bc4>] (dump_stack+0x84/0x98)
[ 3.010251] [<c05e4bc4>] (dump_stack) from [<c0014038>] (handle_IPI+0x164/0x198)
[ 3.011101] [<c0014038>] (handle_IPI) from [<c00085d0>] (gic_handle_irq+0x58/0x5c)
[ 3.011970] [<c00085d0>] (gic_handle_irq) from [<c0011c80>] (__irq_svc+0x40/0x50)
[ 3.012828] Exception stack(0xcd8cbf98 to 0xcd8cbfe0)
[ 3.013408] bf80: ffffffed 0d7de000
[ 3.014345] bfa0: c07f7468 00000000 cd8ca000 c07f6420 c07f649c cd8ca000 c05eb88c c0827921
[ 3.015281] bfc0: c06e0e08 cd8ca000 c07fe2d4 cd8cbfe0 c000eeb4 c000eeac 600d0013 ffffffff
[ 3.016221] [<c0011c80>] (__irq_svc) from [<c000eeac>] (arch_cpu_idle+0x2c/0x38)
[ 3.017073] [<c000eeac>] (arch_cpu_idle) from [<c00636f4>] (cpu_startup_entry+0xf4/0x134)
[ 3.018016] [<c00636f4>] (cpu_startup_entry) from [<00008664>] (0x8664)
l
-
-
-
-