well it is also a console device, which means you can logon via this port also.
Logon and flash?
well it is also a console device, which means you can logon via this port also.
Logon and flash?
There is one service port which is the small USB with the description "Service". Other USB ports exist for some Dreamboxes only.
Yes, shure service USB for bootlog only?
Thax all,sorry Dreambox USB port only for bootlog use?
where can I see / check which value the Network Card has in a DM900 ?
?
Thanx diehummel,the bottleneck is DreamboxCC Telnet Prog?!!After connection via FileZilla transfer speed increased to 85 mb/sec!
apt-get update && apt-get install ethtool
ethtool eth0
have you checked if "IntelliQoS" is enabled in your router?
I did it.
IntelliQoS is disabled
Router determines 1000 mbit/sec connection,but best result is 24 mb/sec(~200 mbit) only.
ZyXEL Keenetic U II MT7621A 880mghz 2 core
telnet:upt-get command not found
Read his first post and check if auto-negotiation detected your network as 100MBit instead of 1000MBit
Router Model?
Stock Firmware? DDWRT or Openwrt? Another Switch between DM900 and Router?
Your PC has Gigabit? Maybe your PC just has 100Mbit.
Router zyxel Stock firmware,no switches,PC 1gb card ,router to PC lan is Ok 1gb
Read my first post again
What can I do?
I got 523 MBit/s = 65,4 MB/s here with my 7080 in terms of network throughput from my local server.
However, that doesn't really help villa at all, does it?
Could be some power saving options enabled on your router that is preventing a Gig link.Maybe you could play around with thoses settings or try another router or switch. Also trying another cable might help.
My router and my PC network card both 1gb,I tried 2 cables...12 mb/sec...
Hello!Why Ethernet speed so low with my 1000Mbit router?Only 12 MB/sec(100mbit) file transfer.Cable link cat.6 .
P.S DM 900 Wlan USB stick link is OK 14-20 MB/sec.
what version does it show when it is loaded ?
Flash latest OE2.5 Experimental, then follow Bruce Willis' advice and enter
update-rescue in telnet.
Version#103. Sorry ,I do not understand about B.Willis..
Then you maybe should consider to follow the given advice
gutemine,once and again I update the loader ...
Why every time when I backup or upload new image appear this warning? Warning: Could not read CA!
Warning: Please consider updating your rescue loader!
In case when image not run and telnet not work .How I can update the image via serial?
In recovery mode
Remounting '/dev/mmcblk0p3' to '/data'
Downloading 'http://dreamboxupdate.com/download/recovery/dm900/release/recovery.sig'
Copying 'recovery' from local storage
Verifying signature of 'recovery'
gpgv: Signature made Wed Dec 21 02:02:08 2016 UTC using RSA key ID 7DA27561
gpgv: Good signature from "Dreambox DM900 Recovery <dm900@recovery.dreambox.de>"
Unmounting '/data'
Running './recovery'
Options '-v -b -r'
Mounting '/dev/mmcblk0p3' to '/data'
Downloading 'http://dreamboxupdate.com/download/recovery/dm900/release/dreambox-image-dm900.tar.xz.sig'
Copying 'dreambox-image-dm900.tar.xz' from local storage
Verifying signature of 'dreambox-image-dm900.tar.xz'
gpgv: Signature made Sat Dec 10 00:27:46 2016 UTC using RSA key ID 7DA27561
gpgv: Good signature from "Dreambox DM900 Recovery <dm900@recovery.dreambox.de>"
Mounting '/dev/mmcblk0p2' to '/mnt'
sed: /mnt/etc/shadow: No such file or directory
Unmounting '/mnt'
Unmounting '/data'
Fatal: Failed to execute './recovery'
When I try firmware upload
[*] Remounting '/dev/mmcblk0p3' to '/data'[*] Mounting '/dev/mmcblk0p2' to '/mnt'sed: /mnt/etc/shadow: No such file or directory[*] Unmounting '/mnt'
How I can load the image?
As far as I can tell, you already updated your loader. So don't waste your time trying again.
If you want to update your rescue loader again later, do it from a normal boot (i.e. when enigma2 is running).
OK,what can I do if enigma 2 is not running?
No. But sometimes electronic parts can break...
And yes. You can remove the tuner yourself or let the dealer / DMM replace the tuner. If you bought the box in Europe the dealer is obligated to fix the problem.
I heard that new DVB 2SX Tuner is comin?
I think you dont understand... you have to send the tuner to DMM or your dealer... the voltage regulator is broken....
cu
It is common problem?
Tuner is removable?
https://www.marcush.de/2016/10…-dreambox-dm-900-ultrahd/
What does it mean in specification?
PCIe connectivity to Broadcom BCM4366 4×4 carrier-grade Wi-Fi