Beiträge von h2402

    Hallo! Ich habe eine a867 (LED blau) und das letzte stabile Image (20200720) auf meiner dm525-Combo installiert. Ich mache auf Telnet: opkg installiere kernel-module-dvb-usb-a867 Aber nach dem Neustart kann ich den USB-Tuner nicht in der Tuner-Einstellung finden ... (Ich sehe nur A- und B-Tuner, aber mit dem alten Image 2018 sehe ich auch Tuner C) Wie kann ich das beheben? Vielen Dank

    Schau bitte mal nach welcher Tuner dir angezeigt wird. Das geht ganz sicher wenn du einen SiLabs hast und A1 auf einfach + Rotor steht. Dann ist die Option auf A2 auswählbar.

    Tuner A1: BCM45308X

    Konfiguration: einfach

    Modus: Rotor

    Rotor wird exclusiv nur an dieser Dreambox betriebe: Ja

    SCPC optimierter Suchbereich: nein


    Tuner A2: BCM45308X=

    Konfiguration: einfach oder erweitert ??

    Modus: Einzeln, Tonebrust A/B, DiSEqC A/B, DiSEqC A/B/C/D, Rotor


    Ich habe nur diese Parameter, die ich nicht finde zusätzliches Kabel eines Rotors.

    Danke

    Hallo!

    Ich habe einen dm920 mit Twin DVB-S2 Multistream Tuner.

    Ich habe zwei Kabel, die von meinem Dach kommen, meine Antenne hat eine USALS-Schale mit einem Twin-LNB:

    Eine ist die Legacy-Ausgabe, die den USALS-Motor steuert, und die zweite ist die Ausgabe SCR / dCSS.


    Meine Frage: Tuner A ist für die Verwendung von USALS Motor eingestellt und ich habe das Kabel vom Legacy-Ausgang eingesteckt.

    Wie kann ich den Tuner B von Dm920 so einrichten, dass das zweite Kabel vom selben LNB verwendet wird, das jedoch das SCR-Signal überträgt?


    In meinem alten DM7020 gibt es eine Option namens: Zweites Kabel von

    Motorisierte Schüssel ... jetzt kann ich das nicht finden.


    Vielen Dank

    Hello!
    I’ve an dm920 with two dvb-s2 tuners i’ve an USALS motor and two cable down the LNB (an GT-SAT WITH 1dcss+3legacy) one cable is from USALS rotor(legacy) and the other is attached directly on dcss out.


    How i can setup my dm920 to manage this config?


    Thanks

    Hello!
    I've an dm525 with original dreamos image.


    I've inserted an USB key but i mounted him in /media/sanusbdisk..
    I would to change mount path in /media/hdd to enable recording PVR..
    How i can do that?
    If i change with telnet, after reboot the dreambox mount on old path: /media/sanusbdisk


    Thanks a lot

    Hello!
    Any solution to have video from a channel and audio from another on the new dm900/920 ?


    FBC Tuner and no way to listen other audio channel, this features work on dm8000 and dm7080 very useful to listen audio on own language expecially during live events!.
    Hope on a gutemine’s miracle

    I've got 4 lnbs with programmable pins with the similar configuration as you have mentioned with pin active. But every time I want to add a new device I have to re-program all 4 lnbs to allow new device to use it's own pin. I tried to set the pin all the same but it works the same like no pin at all. For me there is a strange situation with no pin active. Even when I have specific user band assigned to each from 24 tuners, from time to time I got message "Tuning failed" and I have to turn off the power inserters (which are necessary for 4 lnbs). Then I can tune the same frequency again. It happens at least once a day. With pin active I have no issue.
    I will try your plugin, thanks for suggestion.


    FBC Tuner A1 can receive up to 4 PIN ? And A2 another 4 PIN?
    If i connect dcss at only A1 and it loop internal this the total pin are 4+4 = 8 PIN (demodularoren). Right?
    Well i’ve free another 8 PIN (if i use an dcss lnb with 16 PIN) to user it on other decoder. Right?


    Many many thanks gutemine!!! :smiling_face: :smiling_face: :smiling_face:

    Hello!


    I've found a great plugin to mask logo to prevent ruin my oled tv.
    but if i install in the DreamOS 2.5 give me a lot of error.


    Anyone have one that work on DreamOs?


    Thanks