I just found out that when I connected my 1.2 Dish instead of my 1.5 Dish to the Dreambox 920 the frequency came in without any problem.
Now with my 1.5 Dish connected to the 920 UHD all other Satellites transponders are ok. Perhaps the 1.5 is saturating the Tuner too much?
I did do a blind scan, but nothing comes in on this particular Frequency. With my other Dreambox 900UHD having a multiStream tuner only, I have no problem.
With my 920 UHD The Tuner is a Fbc Multistream.
I have another problem....I cannot tune in the Frequency 12732 V 29950 2/3 8PSK on 5 West as well (Fransat UHD)
This is not a Multi stream Frequency. Even when I do a 'Manual scan' the Freq cannot be received.
Ok Thanks very much. It is ok now. Thank you again.
Good evening I have a dreambox 920 with FBC Tuner (BCM45308X) and I have this problem that when go to 5West Satellite I cannot see the
signal strength in 'Positioner setup' although in 'normal display' I can see it. I have changed the skins but it still remains the same. Is it because of the Tuner being FBC?
[Blockierte Grafik: https://board.newnigma2.to/wbb4/index.php/Attachment/41408-5-West-Fransat-3-Sat-HD-png/?thumbnail=1][Blockierte Grafik: https://board.newnigma2.to/wbb4/index.php/Attachment/41409-France-3-png/?thumbnail=1]
Good evening I have a dreambox 920 with FBC Tuner (BCM45308X) and I have this problem that when I go to 5 West Satellite I cannot see the
signal strength in 'Positioner setup' on some Channels although in 'normal display' I can see it. I have changed the skins but it still remains the same. Is it because of the Tuner being FBC? I am using Newnigma Image.
[Blockierte Grafik: https://board.newnigma2.to/wbb4/index.php/Attachment/41408-5-West-Fransat-3-Sat-HD-png/?thumbnail=1][Blockierte Grafik: https://board.newnigma2.to/wbb4/index.php/Attachment/41409-France-3-png/?thumbnail=1]
Good evening I have a dreambox 920 with FBC Tuner (BCM45308X) and I have this problem that when I go to 5 West Satellite I cannot see the
signal strength in 'Positioner setup' on some Channels although in 'normal display' I can see it. I have changed the skins but it still remains the same. Is it because of the Tuner being FBC? I am using Newnigma Image.
[Blockierte Grafik: https://board.newnigma2.to/wbb4/index.php/Attachment/41408-5-West-Fransat-3-Sat-HD-png/?thumbnail=1][Blockierte Grafik: https://board.newnigma2.to/wbb4/index.php/Attachment/41409-France-3-png/?thumbnail=1]
Good morning,
I have a query. I ordered and received a should be DVB S2X MultiStream dual Tuner for my DM900UHD. BUT this Tuner which I received does NOT have
on it's printed board an ''S2X-MS'' and it MOD date is 2016/4 (Si21662 Dual REV B2) whilst on the package box the date is MOD 2017/6 si21662 B4.
Now when I tried it the MultiStream Bouquets they remained 'greyed out' and also when I did a manual scan on one Multistream Frequency, nothing was
scanned in. I came to the conclusion that I was given another type of Tuner but not a MultiStream one.
Can anyone please confirm my conclusion to be certain that this is the wrong Tuner.
Ok thanks. What I checked was the Power Supply Voltages from pin 1 to 14 and they were all correct. (I found the readings in the Internet)
A few days ago I changed two Electrolytic Capacitors from the P/S although they weren't bad just slightly out of capacitance.
I had a look at the Sim which seemed to be Ok physically (electrically I don't know) Well that's about it
Can't go further than that. I cannot check any I.C's or SMD's (surface mount devices).
Mine is an genuine Dreambox. I don't believe in clones. In fact I have Three Boxes. All Genuine dreamboxes.
No only serial not the network because I don't know the IP address since the box is not responding at all.
Thank you for your interest.
Ok somehow I managed to connect with my Dreambox, somehow! and I uploaded Flash loader then Dreamup
states ''upload complete, waiting for acknowledgement''....but the acknowledgement NEVER comes....
Yes I am using a USB to serial cable and the port is ok.
That's what I did, but not connection was established with Dreamup not ever.
I found the Security sims, it was under the Hard Drive, but it was OK. also checked the Electrolytic Capacitors in the Power
supply. Removed them one by one and checked their capacitance but they were OK as well.
I used Dreamup but it won't connect with the Dreambox because as soon as I connect it and switch it 'ON' the OLED
display 'ERROR' and Dreamup does not connect at all. So that's it.
Ok thank you.
Mine is an Original Dreambox. Does it also have a security sim, just asking.
Ok thank you, BTW do you know where where the security sim is in the dreambox 8000 chassis.
I don't have a serial port on my computer to be able to connect DreamUP. Only HDMI OR USB. Please Where is the security sim in the chassis
to be able to check it
Good afternoon. Can anyone please help me getting my DreamBox 8000 Boot up again, because since yesterday the Box is showing an ''ERROR''
in the Display (OLED) Screen and it won't boot up at all. About 3 months ago it started to have a blank OLED Screen when ever I switch it ON the first time
But on the second attempt it boots up perfectly, it kept doing this always but as I said NOW it is showing an 'ERROR' on the OLED.
