hi dear all dm box users
i have a boot problem
while i was flashing image the light went out
after that the box doesnt boot
even rescue mode dosnt work
still stick in ! on the screen without any ip
this is putty log
CPU 01
Dreambox DM920
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=000003ad(941)
temperature=0000ba60(47712)
PV=00000364(868)
MV=000003ac(940)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 07080d30
_ebss 0713ddd0
_end 0713ddf0
HEAP @ 07200000
STACK @ 09300000
ARCH: CONFIG OK
CLR BSS 07080d30 to 0713ddd0 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
,/
,'/___, BOLT v1.18 v1.18 LOCAL BUILD
.'__ ,' (2017-11-08 00:35:37 cynric@cynric-VirtualBox)
/,' Copyright (C) 2017 Broadcom
/'
Board: BCM97252SSFF
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
CS1: NAND: unrecognized ID: 0xffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
card if inited
set pwm to 0/255
disp id ffff
load image
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.941V, T=+49.173C, PV=0.868V, MV=0.940V, FW=30333278 [0.3.2.x]
USB otp=00000040
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
init fp
ATR length 18b. TPM version 1
found card in unknown state
ca valid!
set pwm to 200/255
Normal bootup
Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:(null)
Reading 4249192 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7728000)
32 bit boot...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14-1.17-dm920 (dm920@opendreambox.org) (gcc version 5.3.0 (GCC) ) #2 SMP Fri Feb 9 16:42:57 UTC 2018
[ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: BCM97252SSFF
[ 0.000000] moving dtb from 0x0000000007728000 to 0x0000000000835e70
[ 0.000000] bmem: Reserved 640 MiB at 0x0000000018000000
[ 0.000000] bmem: Reserved 384 MiB at 0x0000000080000000
[ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] MCP: Enabling write pairing
[ 0.000000] PERCPU: Embedded 8 pages/cpu @cdfc0000 s8384 r8192 d16192 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523776
[ 0.000000] Kernel command line: bmem=640M@384M bmem=384M@2048M console=ttyS0,1000000 root=/dev/mmcblk0p2 rootwait rootfstype=ext4 coherent_pool=2M
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 1006912K/2097152K available (6114K kernel code, 214K rwdata, 1588K rodata, 244K init, 208K bss, 1073856K reserved, 16384K cma-reserved, 786428K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc078dcec (7704 kB)
[ 0.000000] .init : 0xc078e000 - 0xc07cb0c0 ( 245 kB)
[ 0.000000] .data : 0xc07cc000 - 0xc0801b20 ( 215 kB)
[ 0.000000] .bss : 0xc0801b28 - 0xc0835e70 ( 209 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
[ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[ 0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
[ 0.000009] Switching to timer-based delay loop
[ 0.000235] Console: colour dummy device 80x30
[ 0.000255] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[ 0.000264] pid_max: default: 32768 minimum: 301
[ 0.000359] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000364] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.005895] Initializing cgroup subsys devices
[ 0.005909] Initializing cgroup subsys freezer
[ 0.005916] Initializing cgroup subsys net_cls
[ 0.005942] CPU: Testing write buffer coherency: ok
[ 0.006157] CPU0: update cpu_power 1024
[ 0.006163] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.006212] Setting up static identity map for 0x5d5ab8 - 0x5d5b10
[ 0.007445] CPU1: Booted secondary processor
[ 0.007462] CPU1: update cpu_power 1024
[ 0.007464] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.007533] Brought up 2 CPUs
[ 0.007543] SMP: Total of 2 processors activated (108.00 BogoMIPS).
[ 0.007548] CPU: All CPU(s) started in SVC mode.
[ 0.007928] devtmpfs: initialized
[ 0.011520] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[ 0.012080] regulator-dummy: no parameters
[ 0.012246] NET: Registered protocol family 16
[ 0.013168] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.013353] cpuidle: using governor ladder
[ 0.013358] cpuidle: using governor menu
[ 0.014491] irq: no irq domain found for /rdb/interrupt-controller@f040a700 !
[ 0.014575] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.016275] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] registered
[ 0.016351] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
[ 0.016418] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
[ 0.016481] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
[ 0.016546] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
[ 0.016613] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
[ 0.016679] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
[ 0.016741] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
[ 0.016804] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
[ 0.016874] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
[ 0.016939] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
[ 0.017001] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
[ 0.017064] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
[ 0.017142] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
[ 0.017452] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.017677] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[ 0.022055] bio: create slab <bio-0> at 0
[ 0.022362] brcmstb-gpio f040a600.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
[ 0.022387] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
[ 0.022413] brcmstb-gpio f0417400.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
[ 0.022426] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
[ 0.022778] SCSI subsystem initialized
[ 0.022992] usbcore: registered new interface driver usbfs
[ 0.023022] usbcore: registered new interface driver hub
[ 0.023081] usbcore: registered new device driver usb
[ 0.023101] media: Linux media interface: v0.10
[ 0.023126] Linux video capture interface: v2.00
[ 0.023179] pps_core: LinuxPPS API ver. 1 registered
[ 0.023182] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.023192] PTP clock support registered
[ 0.023410] Advanced Linux Sound Architecture Driver Initialized.
[ 0.023690] Bluetooth: Core ver 2.18
[ 0.023703] NET: Registered protocol family 31
[ 0.023706] Bluetooth: HCI device and connection manager initialized
[ 0.023715] Bluetooth: HCI socket layer initialized
[ 0.023721] Bluetooth: L2CAP socket layer initialized
[ 0.023727] Bluetooth: SCO socket layer initialized
[ 0.024134] Switched to clocksource arch_sys_counter
[ 0.024144] cfg80211: Calling CRDA to update world regulatory domain
[ 0.028485] thermal thermal_zone0: failed to read out thermal zone 0
[ 0.028569] NET: Registered protocol family 2
[ 0.028968] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.028984] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.029006] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.029040] TCP: reno registered
[ 0.029046] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.029058] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.029191] NET: Registered protocol family 1
[ 0.029414] RPC: Registered named UNIX socket transport module.
[ 0.029419] RPC: Registered udp transport module.
[ 0.029422] RPC: Registered tcp transport module.
[ 0.029426] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.030021] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.030367] bounce pool size: 64 pages
[ 0.030886] NFS: Registering the id_resolver key type
[ 0.030917] Key type id_resolver registered
[ 0.030921] Key type id_legacy registered
[ 0.030932] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.031065] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 0.031375] msgmni has been set to 462
[ 0.032104] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.032111] io scheduler noop registered
[ 0.032143] io scheduler cfq registered (default)
[ 0.032372] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
[ 0.032660] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
[ 0.098413] brcmstb_memc f1102000.memc-ddr: registered
[ 0.098439] brcmstb_memc f1182000.memc-ddr: registered
[ 0.098636] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.099452] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
[ 0.196058] console [ttyS0] enabled
[ 0.197309] loop: module loaded
[ 0.197946] ahci brcmstb-ahci.0: can't get clock
[ 0.198568] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[ 0.210147] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.211142] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part
[ 0.213782] scsi0 : ahci_platform
[ 0.214420] scsi1 : ahci_platform
[ 0.214924] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
[ 0.215841] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
[ 0.217277] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[ 0.218047] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[ 0.219198] m25p80 spi32766.0: found mx25l25635e, expected m25p80
[ 0.219907] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address
[ 0.220643] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
[ 0.221291] 5 ofpart partitions found on MTD device spi32766.0
[ 0.221961] Creating 5 MTD partitions on "spi32766.0":
[ 0.222561] 0x000000000000-0x000000200000 : "flash0.bolt"
[ 0.223659] 0x000000200000-0x000000220000 : "flash0.nvram"
[ 0.224698] 0x000000220000-0x000000240000 : "flash0.devtree"
[ 0.225751] 0x000000240000-0x000001000000 : "flash0.recovery"
[ 0.226822] 0x000000000000-0x000002000000 : "flash0"
[ 0.228091] libphy: Fixed MDIO Bus: probed
[ 0.228690] tun: Universal TUN/TAP device driver, 1.6
[ 0.229281] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.230320] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[ 0.244137] libphy: bcmgenet MII bus: probed
[ 0.265016] xhci-brcm: xHCI BRCM driver
[ 0.265537] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 0.266209] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[ 0.267388] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
[ 0.268234] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.269015] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.269849] usb usb1: Product: xHCI Host Controller
[ 0.270415] usb usb1: Manufacturer: Linux 3.14-1.17-dm920 xhci-hcd
[ 0.271130] usb usb1: SerialNumber: f0471000.xhci_v2
[ 0.272017] hub 1-0:1.0: USB hub found
[ 0.272480] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 0.273410] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 0.274067] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[ 0.275088] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.275882] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.276723] usb usb2: Product: xHCI Host Controller
[ 0.277293] usb usb2: Manufacturer: Linux 3.14-1.17-dm920 xhci-hcd
[ 0.278002] usb usb2: SerialNumber: f0471000.xhci_v2
[ 0.278847] hub 2-0:1.0: USB hub found
[ 0.279306] hub 2-0:1.0: 2 ports detected
[ 0.280072] ehci-brcm: EHCI BRCM driver
[ 0.280599] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[ 0.281267] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[ 0.292282] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
[ 0.298145] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.298956] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.299744] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.300578] usb usb3: Product: EHCI Host Controller
[ 0.301145] usb usb3: Manufacturer: Linux 3.14-1.17-dm920 ehci_hcd
[ 0.301853] usb usb3: SerialNumber: f0470300.ehci_v2
[ 0.302700] hub 3-0:1.0: USB hub found
[ 0.303159] hub 3-0:1.0: 1 port detected
[ 0.303802] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[ 0.304470] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[ 0.315467] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
[ 0.322138] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.322941] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.323729] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.324564] usb usb4: Product: EHCI Host Controller
[ 0.325132] usb usb4: Manufacturer: Linux 3.14-1.17-dm920 ehci_hcd
[ 0.325840] usb usb4: SerialNumber: f0470500.ehci_v2
[ 0.326149] ata1: SATA link down (SStatus 0 SControl 300)
[ 0.327298] hub 4-0:1.0: USB hub found
[ 0.327750] hub 4-0:1.0: 1 port detected
[ 0.328448] ohci-brcm: OHCI BRCM driver
[ 0.328943] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[ 0.329615] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
[ 0.330540] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
[ 0.386254] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.387035] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.387869] usb usb5: Product: BRCM OHCI controller
[ 0.388436] usb usb5: Manufacturer: Linux 3.14-1.17-dm920 ohci_hcd
[ 0.389151] usb usb5: SerialNumber: f0470400.ohci_v2
[ 0.390004] hub 5-0:1.0: USB hub found
[ 0.390482] hub 5-0:1.0: 1 port detected
[ 0.391152] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[ 0.391813] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
[ 0.392736] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
[ 0.432141] ata2: SATA link down (SStatus 0 SControl 300)
[ 0.448241] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.449021] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.449856] usb usb6: Product: BRCM OHCI controller
[ 0.450423] usb usb6: Manufacturer: Linux 3.14-1.17-dm920 ohci_hcd
[ 0.451138] usb usb6: SerialNumber: f0470600.ohci_v2
[ 0.451962] hub 6-0:1.0: USB hub found
[ 0.452430] hub 6-0:1.0: 1 port detected
[ 0.453121] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.453881] ehci-pci: EHCI PCI platform driver
[ 0.454435] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.455156] ohci-pci: OHCI PCI platform driver
[ 0.455780] usbcore: registered new interface driver usb-storage
[ 0.456481] i2c /dev entries driver
[ 0.456936] lirc_dev: IR Remote Control driver registered, major 250
[ 0.457987] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[ 0.458962] usbcore: registered new interface driver btusb
[ 0.459655] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 0.460474] brcmstb-cpufreq: probe of f03e257c.cpu-clk-div failed with error -17
[ 0.461402] sdhci: Secure Digital Host Controller Interface driver
[ 0.462111] sdhci: Copyright(c) Pierre Ossman
[ 0.462618] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.464366] mmc0: no vqmmc regulator found
[ 0.464842] mmc0: no vmmc regulator found
[ 0.495143] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
[ 0.497048] mmc1: no vqmmc regulator found
[ 0.497527] mmc1: no vmmc regulator found
[ 0.528136] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[ 0.529084] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.529796] usbcore: registered new interface driver usbhid
[ 0.530443] usbhid: USB HID core driver
[ 0.532869] TCP: cubic registered
[ 0.533868] NET: Registered protocol family 10
[ 0.534858] NET: Registered protocol family 17
[ 0.535614] Bluetooth: RFCOMM TTY layer initialized
[ 0.536198] Bluetooth: RFCOMM socket layer initialized
[ 0.536788] Bluetooth: RFCOMM ver 1.11
[ 0.537228] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.537837] Bluetooth: BNEP filters: protocol multicast
[ 0.538445] Bluetooth: BNEP socket layer initialized
[ 0.539016] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.539704] Bluetooth: HIDP socket layer initialized
[ 0.540327] l2tp_core: L2TP core driver, V2.0
[ 0.540847] Key type dns_resolver registered
[ 0.541414] Registering SWP/SWPB emulation handler
[ 0.542239] regulator-dummy: disabling
[ 0.542872] ALSA device list:
[ 0.543236] No soundcards found.
[ 0.543855] Waiting for root device /dev/mmcblk0p2...
[ 0.595784] mmc1: BKOPS_EN bit is not set
[ 0.602497] mmc1: new high speed MMC card at address 0001
[ 0.603312] mmcblk0: mmc1:0001 8GME4R 7.28 GiB
[ 0.603915] mmcblk0boot0: mmc1:0001 8GME4R partition 1 4.00 MiB
[ 0.604709] mmcblk0boot1: mmc1:0001 8GME4R partition 2 4.00 MiB
[ 0.605473] mmcblk0rpmb: mmc1:0001 8GME4R partition 3 512 KiB
[ 0.609408] mmcblk0: p1 p2 p3
[ 0.612323] mmcblk0boot1: unknown partition table
[ 0.613366] mmcblk0boot0: unknown partition table
[ 0.650723] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 0.651685] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 0.654072] devtmpfs: mounted
/sbin/init: error while loading shared libraries: libkmod.so.2: cannot open shared object file: No such file or directory
[ 0.686204] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00
[ 0.686204]
[ 0.687256] CPU: 0 PID: 1 Comm: init Not tainted 3.14-1.17-dm920 #2
[ 0.687995] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x10/0x14)
[ 0.688889] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c)
[ 0.689720] [<c05d0408>] (dump_stack) from [<c05cf770>] (panic+0xa0/0x1f0)
[ 0.690514] [<c05cf770>] (panic) from [<c00208f0>] (complete_and_exit+0x0/0x1c)
[ 0.691353] [<c00208f0>] (complete_and_exit) from [<00000000>] ( (null))
[ 0.692135] CPU1: stopping
[ 0.692452] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14-1.17-dm920 #2
[ 0.693227] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x10/0x14)
[ 0.694117] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c)
[ 0.694948] [<c05d0408>] (dump_stack) from [<c00140d4>] (handle_IPI+0x164/0x198)
[ 0.695798] [<c00140d4>] (handle_IPI) from [<c00085cc>] (gic_handle_irq+0x58/0x5c)
[ 0.696669] [<c00085cc>] (gic_handle_irq) from [<c0011dc0>] (__irq_svc+0x40/0x50)
[ 0.697526] Exception stack(0xcd8cbfa0 to 0xcd8cbfe8)
[ 0.698108] bfa0: ffffffed 0d7ff000 c07d54c8 00000000 cd8ca030 c07d4420 c07d449c c05d788c
[ 0.699045] bfc0: c0801961 c0801961 cd8ca000 00000000 c07dc0c0 cd8cbfe8 c000efb0 c000efa8
[ 0.699981] bfe0: 600f0013 ffffffff
[ 0.700388] [<c0011dc0>] (__irq_svc) from [<c000efa8>] (arch_cpu_idle+0x2c/0x38)
[ 0.701241] [<c000efa8>] (arch_cpu_idle) from [<c00638f8>] (cpu_startup_entry+0x100/0x144)
[ 0.702190] [<c00638f8>] (cpu_startup_entry) from [<00008664>] (0x8664)