Hallo,
habe hier eine 7020HD v1 die noch soweit bootet bis im Display dhcp... angezeigt wird.
Neu flashen per Browser klappt nicht.
Meldung im Browser nachdem das Image hochgeladen wurde: partioning is wrong.
Flashen per DreamUp + UART VCP USB:
Code
18:37:01 box type: DM7020HD
18:37:01 Enabled recovery of bad sectors
18:37:24 Calculating checksum...
18:37:27 Uploading file to box...
Popup nachdem das Image per USB hochgeladen wurde: !!! 004 partition is wrong
Bootlog:
Code
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=FFFFFFF3
RC2=00000014
WC2=00000038
RC3=0000000C
WC3=FFFFFFF2
RC4=0000000C
WC4=00000039
NWC=00000015
RC5=00000005
WC5=00000015
RC6=00000013
WC6=00000015
NRC=0000000C
RW=0000000F
WW=00000048
G=00000000 R=0000000C W=00000015
BL=00000000
RC1=00000001
RC2=00000014
BL=00000001
RC1=00000002
RC2=00000018
BL=00000002
RC1=00000001
RC2=00000010
BL=00000003
RC1=00000003
RC2=00000012
BL=00000004
RC1=00000000
RC2=00000013
BL=00000005
RC1=00000006
RC2=00000019
BL=00000006
RC1=00000004
RC2=00000016
BL=00000007
RC1=00000005
RC2=0000001A
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM7020HD
FIRST STAGE 1.1/400 {BO23456}
2ND STAGE OK, build #89 (2015-03-09)
0.000 - BCM board setup
0.002 - fp init
FP version 6 detected
0.003 - ca init
0.507 - load config
0.534 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #89
P23 detected!
detected 4K pagesize, 256K blocksize
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 256kb
+++++++++++++UUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /boot/bootlogo-dm7020hd.elf.gz
bootlogo size: 42664
Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K !PAL_I !PAL_M !PAL_N !PAL_NC !PAL_60 !SECAM_L !SECAM_B !SECAM_G !SECAM_D !SECAM_K !SECAM_H 1080i !1080p 720p 480p 1080i_50Hz 1080p_24Hz !1080p_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p !DVI_640x480p_CVT DVI_800x600p DVI_1024x768p !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_Red !DVI_640x480p_66Hz !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_640x480p_85Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz !DVI_1920x1080p_60Hz_Red !Custom0 !Custom1
best supported mode is 25
using 1920x1080i (50.00 Hz)
HDMI
using colorspace: 1
create surface 1920 1080
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-3.2-dm7020hd.gz
[ 0.000000] Linux version 3.2-dm7020hd (weazle@toxbox.merlin3.info) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Thu Jul 16 15:55:40 CEST 2015
[ 0.000000] Fetching vars from bootloader...
[ 0.000000] Early serial console at MMIO32 0x10400b00 (options '1000000n8')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
[ 0.000000] Using 512 MB RAM (from straps)
[ 0.000000] Fetch var 'memsize' = '64'
[ 0.000000] CPU revision is: 0002a044 (Brcm4380)
[ 0.000000] FPU revision is: 00130001
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] memory: 10000000 @ 20000000 (usable)
[ 0.000000] bmem: adding 58 MB LINUX region at 5 MB (0x03a06000@0x005fa000)
[ 0.000000] bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
[ 0.000000] bmem: adding 256 MB LINUX region at 512 MB (0x10000000@0x20000000)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00030000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00010000
[ 0.000000] 0: 0x00020000 -> 0x00030000
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] Normal zone: 1536 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 129536 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81407000 s5440 r8192 d15040 u32768
[ 0.000000] pcpu-alloc: s5440 r8192 d15040 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
[ 0.000000] Kernel command line: ubi.mtd=root root=ubi0:rootfs rootfstype=ubifs rw console=ttyS0,115200 debug bmem=192M@64M
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.000000] Memory: 316976k/524288k available (4755k kernel code, 207312k reserved, 1008k data, 224k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Measuring MIPS counter frequency...
[ 0.000000] Detected MIPS clock frequency: 405 MHz (202.504 MHz counter)
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop... 403.45 BogoMIPS (lpj=201728)
[ 0.011000] pid_max: default: 32768 minimum: 301
[ 0.012000] Mount-cache hash table entries: 512
[ 0.014000] SMP: Booting CPU1...
[ 0.015000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.015000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.016000] CPU revision is: 0002a044 (Brcm4380)
[ 0.016000] FPU revision is: 00130001
[ 0.026000] SMP: CPU1 is running
[ 0.026000] Brought up 2 CPUs
[ 0.027000] devtmpfs: initialized
[ 0.031000] NET: Registered protocol family 16
[ 0.033000] PCI2.3->SDRAM window: 512 MB
[ 0.040000] bio: create slab <bio-0> at 0
[ 0.042000] SCSI subsystem initialized
[ 0.042000] libata version 3.00 loaded.
[ 0.043000] usbcore: registered new interface driver usbfs
[ 0.043000] usbcore: registered new interface driver hub
[ 0.044000] usbcore: registered new device driver usb
[ 0.045000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.046000] pci 0000:01:00.0: [14e4:8602] type 0 class 0x000101
[ 0.047000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
[ 0.047000] pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
[ 0.048000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
[ 0.049000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
[ 0.050000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff])
[ 0.051000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
[ 0.052000] Switching to clocksource upg
[ 0.065000] NET: Registered protocol family 2
[ 0.097000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.099000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.101000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.102000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.103000] TCP reno registered
[ 0.104000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.105000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.106000] NET: Registered protocol family 1
[ 0.107000] RPC: Registered named UNIX socket transport module.
[ 0.108000] RPC: Registered udp transport module.
[ 0.108000] RPC: Registered tcp transport module.
[ 0.109000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.110000] PCI: CLS 0 bytes, default 64
[ 0.114000] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.115000] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[ 0.118000] msgmni has been set to 619
[ 0.119000] io scheduler noop registered
[ 0.120000] io scheduler cfq registered (default)
[ 0.121000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
▒[ 0.143000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
[ 0.144000] console [ttyS0] enabled, bootconsole disabled
[ 0.144000] console [ttyS0] enabled, bootconsole disabled
[ 0.166000] serial8250.0: ttyS1 at MMIO 0x10400b80 (irq = 67) is a 16550A
[ 0.169000] loop: module loaded
[ 0.169000] sata_brcmstb 0000:01:00.0: version 4.0
[ 0.170000] brcm-pm: enabling sata clocks
[ 0.171000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
[ 0.171000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 0.369000] scsi0 : sata_brcmstb
[ 0.370000] scsi1 : sata_brcmstb
[ 0.371000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
[ 0.372000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
[ 0.374000] Broadcom STB NAND controller (BrcmNand Controller)
[ 0.374000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0
[ 0.378000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:2d:18:bd)
[ 0.379000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.380000] brcm-pm: enabling usb clocks
[ 0.380000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.381000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 0.413000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
[ 0.419000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.420000] hub 1-0:1.0: USB hub found
[ 0.421000] hub 1-0:1.0: 2 ports detected
[ 0.421000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[ 0.422000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
[ 0.454000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
[ 0.460000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[ 0.461000] hub 2-0:1.0: USB hub found
[ 0.461000] hub 2-0:1.0: 2 ports detected
[ 0.462000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.463000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.464000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
[ 0.465000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
[ 0.530000] hub 3-0:1.0: USB hub found
[ 0.531000] hub 3-0:1.0: 2 ports detected
[ 0.532000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[ 0.532000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
[ 0.533000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
[ 0.599000] hub 4-0:1.0: USB hub found
[ 0.600000] hub 4-0:1.0: 2 ports detected
[ 0.601000] Initializing USB Mass Storage driver...
[ 0.602000] usbcore: registered new interface driver usb-storage
[ 0.602000] USB Mass Storage support registered.
[ 0.603000] i2c /dev entries driver
[ 0.603000] ALSA device list:
[ 0.604000] No soundcards found.
[ 0.605000] TCP cubic registered
[ 0.605000] NET: Registered protocol family 17
[ 0.606000] Registering the dns_resolver key type
[ 0.606000] EBI CS1: setting up NAND flash (primary)
[ 0.607000] mtd->oobsize=0, mtd->eccOobSize=0
[ 0.608000] NAND_CS_NAND_XOR=00000000
[ 0.608000] B4: NandSelect=40000202, nandConfig=48252300, chipSelect=1
[ 0.609000] brcmnand_read_id: CS1: dev_id=ecd310a6
[ 0.610000] After: NandSelect=40000202, nandConfig=48252300
[ 0.611000] Block size=00040000, erase shift=18
[ 0.611000] NAND Config: Reg=48252300, chipSize=1024 MB, blockSize=256K, erase_shift=12
[ 0.612000] busWidth=1, pageSize=4096B, page_shift=12, page_mask=00000fff
[ 0.613000] timing1 not adjusted: 5363444f
[ 0.613000] timing2 not adjusted: 00000fc6
[ 0.614000] eccLevel=15, 1Ksector=0, oob=16
[ 0.614000] nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
[ 0.615000] <--brcmnand_set_acccontrol: acc b4: f7ff1010, after: f7ff1010
[ 0.616000] BrcmNAND mfg ec d3 Samsung K9F8G08U0M 1024MB on CS1
[ 0.617000]
[ 0.617000] Found NAND on CS1: ACC=f7ff1010, cfg=48252300, flashId=ecd310a6, tim1=5363444f, tim2=00000fc6
[ 0.618000] BrcmNAND version = 0x0302 1024MB @00000000
[ 0.619000] B4: NandSelect=40000202, nandConfig=48252300, chipSelect=1
[ 0.619000] brcmnand_read_id: CS1: dev_id=ecd310a6
[ 0.620000] After: NandSelect=40000202, nandConfig=48252300
[ 0.621000] Found NAND flash on Chip Select 1, chipSize=1024MB, usable size=1024MB, base=0
[ 0.622000] brcmnand_scan: B4 nand_select = 40000202
[ 0.622000] brcmnand_scan: After nand_select = 40000202
[ 0.623000] page_shift=12, bbt_erase_shift=18, chip_shift=30, phys_erase_shift=18
[ 0.624000] Brcm NAND controller version = 3.2 NAND flash size 1024MB @00000000
[ 0.625000] ECC layout=brcmnand_oob_128
[ 0.625000] brcmnand_scan: mtd->oobsize=128
[ 0.626000] brcmnand_scan: oobavail=102, eccsize=512, writesize=4096
[ 0.626000] brcmnand_scan, eccsize=512, writesize=4096, eccsteps=8, ecclevel=15, eccbytes=3
[ 0.627000] -->brcmnand_default_bbt
[ 0.628000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[ 0.629000] Bad block table Bbt0 found at page 0003ffc0, version 0x01 for chip on CS1
[ 0.630000] Bad block table 1tbB found at page 0003ff80, version 0x01 for chip on CS1
[ 0.632000] nand_read_bbt: Bad block at 0x05300000
[ 0.633000] brcmnandCET: Status -> Deferred
[ 0.633000] Adjust partition complete size from 40000000 to 3ff00000 to avoid overlap with BBT reserved space
[ 0.635000] Adjust partition root size from 3f800000 to 3f700000 to avoid overlap with BBT reserved space
[ 0.636000] Creating 4 MTD partitions on "brcmnand.0":
[ 0.637000] 0x000000000000-0x00003ff00000 : "complete"
[ 0.642000] 0x000000000000-0x000000100000 : "loader"
[ 0.644000] 0x000000100000-0x000000800000 : "boot"
[ 0.646000] 0x000000800000-0x00003ff00000 : "root"
[ 0.654000] UBI: attaching mtd3 to ubi0
[ 0.655000] UBI: physical eraseblock size: 262144 bytes (256 KiB)
[ 0.655000] UBI: logical eraseblock size: 253952 bytes
[ 0.656000] UBI: smallest flash I/O unit: 4096
[ 0.657000] UBI: VID header offset: 4096 (aligned 4096)
[ 0.657000] UBI: data offset: 8192
[ 0.678000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.683000] ata1.00: ATA-8: TOSHIBA DT01ACA100, MS2OA750, max UDMA/133
[ 0.684000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 0.692000] ata1.00: configured for UDMA/133
[ 0.693000] scsi 0:0:0:0: Direct-Access ATA TOSHIBA DT01ACA1 MS2O PQ: 0 ANSI: 5
[ 0.695000] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 0.696000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 0.697000] sd 0:0:0:0: [sda] Write Protect is off
[ 0.697000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.698000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.735000] sda: sda1
[ 0.737000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.764000] usb 2-1: new high-speed USB device number 2 using ehci-brcm
[ 1.022000] ata2: SATA link down (SStatus 4 SControl 300)
[ 1.429000] brcmnand_ctrl_verify_ecc: Correctable ECC error at 00010000:0b4c1e00
[ 1.466000] brcmnand_handle_false_read_ecc_unc_errors: Uncorrectable error at offset bd41200
[ 1.467000] Data:
[ 1.467000]
[ 1.467000] 0000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.469000] 0020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.470000] 0040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.471000] 0060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.472000] 0080: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.474000] 00a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.475000] 00c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.476000] 00e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.477000] 0100: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.479000] 0120: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.480000] 0140: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.481000] 0160: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.482000] 0180: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.484000] 01a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.485000] 01c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.486000] 01e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.487000] Spare Area
[ 1.488000] ffffffff ffff7fff ffffffff ffffffff
[ 1.488000] brcmnand_post_mortem_dump at offset bd41200
[ 1.489000] Call Trace:
[ 1.489000] [<8049d3d4>] dump_stack+0x8/0x34
[ 1.490000] [<803654f4>] brcmnand_post_mortem_dump+0x54/0x120
[ 1.491000] [<80365db0>] brcmnand_ctrl_posted_read_cache+0x78c/0x91c
[ 1.491000] [<8036252c>] brcmnand_read_page+0x12c/0x25c
[ 1.492000] [<803647b8>] brcmnand_do_read_ops+0x150/0x268
[ 1.493000] [<803649bc>] brcmnand_read+0xec/0x89c
[ 1.493000] [<8035c100>] part_read+0x8c/0x138
[ 1.494000] [<803786e8>] ubi_io_read+0x98/0x1bc
[ 1.494000] [<80378f84>] ubi_io_read_vid_hdr+0x58/0x4bc
[ 1.495000] [<8037cbd4>] ubi_scan+0x388/0xb74
[ 1.495000] [<803731b4>] ubi_attach_mtd_dev+0x5d4/0xbd8
[ 1.496000] [<805b95b4>] ubi_init+0x2e4/0x3f0
[ 1.497000] [<80001570>] do_one_initcall+0x160/0x1f0
[ 1.497000] [<805a39f4>] kernel_init+0xd8/0x160
[ 1.498000] [<80006728>] kernel_thread_helper+0x10/0x18
[ 1.498000]
[ 1.499000] NAND registers snapshot
[ 1.499000]
[ 1.499000] 00002800: 00000302 01000000 00010000 0bd41200
[ 1.500000] 00002810: 00000000 40000202 00000000 00000000
[ 1.501000] 00002820: ffffffff ffff7fff ffffffff ffffffff
[ 1.501000] 00002830: ffffffff ffffffff ffffffff ffffffff
[ 1.502000] 00002840: f7ff1010 00000000 48252300 00000000
[ 1.503000] 00002850: 5363444f 00000fc6 00000000 00000000
[ 1.504000] 00002860: ecd310a6 64ecd310 00000000 f0000000
[ 1.504000] 00002870: 00000000 00000000 00000000 00000000
[ 1.505000] 00002880: 00000001 00000001 00000000 00000000
[ 1.506000] 00002890: 00010000 0bd41200 00000000 00000000
[ 1.506000] 000028a0: 00000000 00000000 00000000 00000000
[ 1.507000] 000028b0: 00000000 00000000 00000000 00000000
[ 1.508000] 000028c0: 00000000
[ 1.508000] brcmnand_read_page: 3: brcmnand_posted_read_cache failed at offset=bd41200, ret=-77
[ 1.509000] brcmnand_handle_false_read_ecc_unc_errors: Uncorrectable error at offset bd41200
[ 1.510000] Data:
[ 1.511000]
[ 1.511000] 0000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.512000] 0020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.513000] 0040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.515000] 0060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.516000] 0080: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.517000] 00a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.518000] 00c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.520000] 00e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.521000] 0100: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.522000] 0120: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.523000] 0140: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.525000] 0160: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.526000] 0180: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.527000] 01a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.528000] 01c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.530000] 01e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.531000] Spare Area
[ 1.531000] ffffffff ffff7fff ffffffff ffffffff
[ 1.532000] brcmnand_post_mortem_dump at offset bd41200
[ 1.532000] Call Trace:
[ 1.533000] [<8049d3d4>] dump_stack+0x8/0x34
[ 1.533000] [<803654f4>] brcmnand_post_mortem_dump+0x54/0x120
[ 1.534000] [<80365db0>] brcmnand_ctrl_posted_read_cache+0x78c/0x91c
[ 1.535000] [<8036252c>] brcmnand_read_page+0x12c/0x25c
[ 1.535000] [<803647b8>] brcmnand_do_read_ops+0x150/0x268
[ 1.536000] [<803649bc>] brcmnand_read+0xec/0x89c
[ 1.537000] [<8035c100>] part_read+0x8c/0x138
[ 1.537000] [<80378740>] ubi_io_read+0xf0/0x1bc
[ 1.538000] [<80378f84>] ubi_io_read_vid_hdr+0x58/0x4bc
[ 1.538000] [<8037cbd4>] ubi_scan+0x388/0xb74
[ 1.539000] [<803731b4>] ubi_attach_mtd_dev+0x5d4/0xbd8
[ 1.539000] [<805b95b4>] ubi_init+0x2e4/0x3f0
[ 1.540000] [<80001570>] do_one_initcall+0x160/0x1f0
[ 1.541000] [<805a39f4>] kernel_init+0xd8/0x160
[ 1.541000] [<80006728>] kernel_thread_helper+0x10/0x18
[ 1.542000]
[ 1.542000] NAND registers snapshot
[ 1.542000]
[ 1.542000] 00002800: 00000302 01000000 00010000 0bd41200
[ 1.543000] 00002810: 00000000 40000202 00000000 00000000
[ 1.544000] 00002820: ffffffff ffff7fff ffffffff ffffffff
[ 1.545000] 00002830: ffffffff ffffffff ffffffff ffffffff
[ 1.545000] 00002840: f7ff1010 00000000 48252300 00000000
[ 1.546000] 00002850: 5363444f 00000fc6 00000000 00000000
[ 1.547000] 00002860: ecd310a6 64ecd310 00000000 f0000000
[ 1.548000] 00002870: 00000000 00000000 00000000 00000000
[ 1.548000] 00002880: 00000001 00000001 00000000 00000000
[ 1.549000] 00002890: 00010000 0bd41200 00000000 00000000
[ 1.550000] 000028a0: 00000000 00000000 00000000 00000000
[ 1.551000] 000028b0: 00000000 00000000 00000000 00000000
[ 1.551000] 000028c0: 00000000
[ 1.552000] brcmnand_read_page: 3: brcmnand_posted_read_cache failed at offset=bd41200, ret=-77
[ 1.553000] brcmnand_handle_false_read_ecc_unc_errors: Uncorrectable error at offset bd41200
[ 1.554000] Data:
[ 1.554000]
[ 1.554000] 0000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.556000] 0020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.557000] 0040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.558000] 0060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.559000] 0080: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.561000] 00a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.562000] 00c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.563000] 00e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.564000] 0100: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.565000] 0120: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.567000] 0140: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.568000] 0160: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.569000] 0180: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.570000] 01a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.572000] 01c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.573000] 01e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.574000] Spare Area
[ 1.575000] ffffffff ffff7fff ffffffff ffffffff
[ 1.575000] brcmnand_post_mortem_dump at offset bd41200
[ 1.576000] Call Trace:
[ 1.576000] [<8049d3d4>] dump_stack+0x8/0x34
[ 1.577000] [<803654f4>] brcmnand_post_mortem_dump+0x54/0x120
[ 1.577000] [<80365db0>] brcmnand_ctrl_posted_read_cache+0x78c/0x91c
[ 1.578000] [<8036252c>] brcmnand_read_page+0x12c/0x25c
[ 1.579000] [<803647b8>] brcmnand_do_read_ops+0x150/0x268
[ 1.579000] [<803649bc>] brcmnand_read+0xec/0x89c
[ 1.580000] [<8035c100>] part_read+0x8c/0x138
[ 1.581000] [<80378740>] ubi_io_read+0xf0/0x1bc
[ 1.581000] [<80378f84>] ubi_io_read_vid_hdr+0x58/0x4bc
[ 1.582000] [<8037cbd4>] ubi_scan+0x388/0xb74
[ 1.582000] [<803731b4>] ubi_attach_mtd_dev+0x5d4/0xbd8
[ 1.583000] [<805b95b4>] ubi_init+0x2e4/0x3f0
[ 1.583000] [<80001570>] do_one_initcall+0x160/0x1f0
[ 1.584000] [<805a39f4>] kernel_init+0xd8/0x160
[ 1.585000] [<80006728>] kernel_thread_helper+0x10/0x18
[ 1.585000]
[ 1.585000] NAND registers snapshot
[ 1.586000]
[ 1.586000] 00002800: 00000302 01000000 00010000 0bd41200
[ 1.587000] 00002810: 00000000 40000202 00000000 00000000
[ 1.587000] 00002820: ffffffff ffff7fff ffffffff ffffffff
[ 1.588000] 00002830: ffffffff ffffffff ffffffff ffffffff
[ 1.589000] 00002840: f7ff1010 00000000 48252300 00000000
[ 1.590000] 00002850: 5363444f 00000fc6 00000000 00000000
[ 1.590000] 00002860: ecd310a6 64ecd310 00000000 f0000000
[ 1.591000] 00002870: 00000000 00000000 00000000 00000000
[ 1.592000] 00002880: 00000001 00000001 00000000 00000000
[ 1.592000] 00002890: 00010000 0bd41200 00000000 00000000
[ 1.593000] 000028a0: 00000000 00000000 00000000 00000000
[ 1.594000] 000028b0: 00000000 00000000 00000000 00000000
[ 1.595000] 000028c0: 00000000
[ 1.595000] brcmnand_read_page: 3: brcmnand_posted_read_cache failed at offset=bd41200, ret=-77
[ 1.596000] brcmnand_handle_false_read_ecc_unc_errors: Uncorrectable error at offset bd41200
[ 1.597000] Data:
[ 1.598000]
[ 1.598000] 0000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.599000] 0020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.600000] 0040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.601000] 0060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.603000] 0080: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.604000] 00a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.605000] 00c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.606000] 00e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.608000] 0100: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.609000] 0120: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.610000] 0140: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.611000] 0160: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.613000] 0180: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.614000] 01a0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.615000] 01c0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.616000] 01e0: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 1.618000] Spare Area
[ 1.618000] ffffffff ffff7fff ffffffff ffffffff
[ 1.619000] brcmnand_post_mortem_dump at offset bd41200
[ 1.619000] Call Trace:
[ 1.620000] [<8049d3d4>] dump_stack+0x8/0x34
[ 1.620000] [<803654f4>] brcmnand_post_mortem_dump+0x54/0x120
[ 1.621000] [<80365db0>] brcmnand_ctrl_posted_read_cache+0x78c/0x91c
[ 1.622000] [<8036252c>] brcmnand_read_page+0x12c/0x25c
[ 1.622000] [<803647b8>] brcmnand_do_read_ops+0x150/0x268
[ 1.623000] [<803649bc>] brcmnand_read+0xec/0x89c
[ 1.623000] [<8035c100>] part_read+0x8c/0x138
[ 1.624000] [<80378740>] ubi_io_read+0xf0/0x1bc
[ 1.624000] [<80378f84>] ubi_io_read_vid_hdr+0x58/0x4bc
[ 1.625000] [<8037cbd4>] ubi_scan+0x388/0xb74
[ 1.626000] [<803731b4>] ubi_attach_mtd_dev+0x5d4/0xbd8
[ 1.626000] [<805b95b4>] ubi_init+0x2e4/0x3f0
[ 1.627000] [<80001570>] do_one_initcall+0x160/0x1f0
[ 1.627000] [<805a39f4>] kernel_init+0xd8/0x160
[ 1.628000] [<80006728>] kernel_thread_helper+0x10/0x18
[ 1.629000]
[ 1.629000] NAND registers snapshot
[ 1.629000]
[ 1.629000] 00002800: 00000302 01000000 00010000 0bd41200
[ 1.630000] 00002810: 00000000 40000202 00000000 00000000
[ 1.631000] 00002820: ffffffff ffff7fff ffffffff ffffffff
[ 1.632000] 00002830: ffffffff ffffffff ffffffff ffffffff
[ 1.632000] 00002840: f7ff1010 00000000 48252300 00000000
[ 1.633000] 00002850: 5363444f 00000fc6 00000000 00000000
[ 1.634000] 00002860: ecd310a6 64ecd310 00000000 f0000000
[ 1.634000] 00002870: 00000000 00000000 00000000 00000000
[ 1.635000] 00002880: 00000001 00000001 00000000 00000000
[ 1.636000] 00002890: 00010000 0bd41200 00000000 00000000
[ 1.637000] 000028a0: 00000000 00000000 00000000 00000000
[ 1.637000] 000028b0: 00000000 00000000 00000000 00000000
[ 1.638000] 000028c0: 00000000
[ 1.638000] brcmnand_read_page: 3: brcmnand_posted_read_cache failed at offset=bd41200, ret=-77
[ 1.640000] UBI error: ubi_io_read: error -77 (ECC error) while reading 4096 bytes from PEB 725:4096, read 0 bytes
[ 1.642000] UBI error: ubi_init: cannot attach mtd3
[ 1.643000] VFS: Cannot open root device "ubi0:rootfs" or unknown-block(8,1)
[ 1.644000] Please append a correct "root=" boot option; here are the available partitions:
[ 1.645000] 1f00 1047552 mtdblock0 (driver?)
[ 1.645000] 1f01 1024 mtdblock1 (driver?)
[ 1.646000] 1f02 7168 mtdblock2 (driver?)
[ 1.647000] 1f03 1039360 mtdblock3 (driver?)
[ 1.647000] 0800 976762584 sda driver: sd
[ 1.648000] 0801 976761836 sda1 00000000-0000-0000-0000-000000000000
[ 1.649000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
[ 1.650000] Rebooting in 180 seconds..
Alles anzeigen
Hardwaredefekt oder noch rettbar?
Falls Flash defekt, wird die Box ersetzt (Booten per USB Stick kommt nicht in frage)
Danke