Hello, or someone has already met with such a thing. The decoder entered this state after entering the menu and selecting the recovery mode, after restarting the display with a red exclamation mark and the inscription dreambox, no ip, no telnet, through putty com I can read the boot log and that's all . Does anyone have any solution for this state of affairs.
-
-
That's exactly what the receiver should do...check your router to find out the ip address. DHCP must be activated to get an ip address
-
dhcp enabled on the router but can't see the dreambox
-
Check your network cables. It's a problem of your network
-
I am surprised this red color has always been a different yellow, the router does not detect the connection although the ip was assigned rigidly checked on 2 routers lan diodes are on
-
It's also possible that the rescue loader does not work properly anymore.
Start a serial connection via the USB service port (putty.exe) and check the network settings via CLI. If not set, you can set IP, gateway and DNS server manually:
-->> RE: DM900 / keien IP Adresse?After flashing and setup the new image update/reinstall the rescue loader when booted from flash:
update-rescue -v -
bootlog putty com + mini usb
CPU 01
Dreambox DM920
AVS init ...
AVS init OK
AVS load: select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset = 00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD: 11138M HW: hpf0_b1p6 V: 2.1.0.0
MCB: FLEX
AVS start: status = 000000ff
STB: Current voltage = 0000039d (925)
temperature = 00006a7a (27258)
PV = 00000359 (857)
MV = 0000039d (925)
AVS FW rev = 30333278 [0.3.2.x]
OKAY
DDR0:! @ Ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: = @ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE ... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 07080d30
_ebss 0713ddd0
_end 0713ddf0
HEAP @ 07200000
STACK @ 09300000
ARCH: CONFIG OK
CLR BSS 07080d30 to 0713ddd0 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
HIM!
, /
, '/ ___, BOLT v1.18 v1.18 LOCAL BUILD
.'__, '(2017-11-08 00:35:37 cynric @ cynric-VirtualBox)
/, 'Copyright (C) 2017 Broadcom
/ '
Board: BCM97252SSFF
SYS_CTRL: product = 72521, family = 7439b1, strap = 000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr (0x00000060) en_testport (0x00000080) macrovision_disable (0x02000000) moca_disable (0x80000000) rv9_disable (0x00200000)
otp @ 0xf0404034 = 0x00000021: powera2_disable (0x00000001) rfm_disable (0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
CS1: NAND: unrecognized ID: 0x7fff 0xffffffff
RTS0: 0x1101004, 256 clients, approx
RTS1: 0x1181004, 256 clients, approx
BOX MODE: 5
card if inited
set pwm is 0/255
disp id ffff
load image
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V = 0.924V, T = + 28.232C, PV = 0.857V, MV = 0.925V, FW = 30333278 [0.3.2.x]
USB otp = 00000040
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
init fp
ATR length 0b. TPM version -1
ATR invalid!
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
usb: resetting device on bus 0 hub 1 port 1
USB: New high speed device connected to bus 0 hub 1 port 1
usb: found Mass-Storage Device abcd: 1234
USBMASS: Unit 0 connected
card if inited
.ATR length 0b. TPM version -1
ATR invalid!
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
retrying .. card if inited
.ATR length 0b. TPM version -1
ATR invalid!
found card in unknown state
cannot read T1 header
error in receive
error during t1 transfer
cannot read fabca-cert
retrying .. card if inited
.set pwm is 200/2/55
TPM error. Please contact Dreambox support
some solution
-
TPM error. Please contact Dreambox support
-
If your configuration:
receiver - lan - pc - "wireless connection" - wi-fi router,
PC does'nt give IP adress, because the PC is slave for wi-fi router and receiver is subslave for wi-fi router.
Wi-fi router doesn't see the receiver.
Solution: on PC (Windows), you have to create "bridge" between 2 conections: LAN - "bridge" - wi-fi. Look it in LAN device settings.
Wi-fi router will see the receiver via LAN connection and give an IP adress.
May be in future I'll make a video how to do it.
