Abspielen von UHD Videos
4K HDR Blender Simulations - YouTube.webm
Bild und Ton einwandfrei, kein HDR
Thx Eclipse Short 4K
Bild Einwandfrei, Ton Rauschen
h264 und h265 UHD Bild immer, Ton bei DTS meistens Rauschen
Load Avg max. 4%
gruß pclin
Abspielen von UHD Videos
4K HDR Blender Simulations - YouTube.webm
Bild und Ton einwandfrei, kein HDR
Thx Eclipse Short 4K
Bild Einwandfrei, Ton Rauschen
h264 und h265 UHD Bild immer, Ton bei DTS meistens Rauschen
Load Avg max. 4%
gruß pclin
kannst mal den GL2 Benchmark mit der Option glmark2-es2 –off-screen testen, wie kommen die auf so Wahnsinnswerte für Odroid N2 (Hardware ziemlich mit der One identisch, ja OK mehr RAM 4GB bei N2), kann sein dass die One noch keine volle Pulle läuft
DTS License halt
UHD Film mit DolbyVision (MP4 Container) wird abgespielt, aber "nur" als "HDR"
(DM920 verweigerte DV MP4 files)
Dolby Digital 5.1 und E-AC3 auch kein Problem. funktioniert.
TOP: CPU: 8,9 bis 11,9 %
anderer UHD Film (mkv Container) mit DTS auch ohne Probleme.
(ton 1a, keine störungen)
downmix an/aus getestet.
Bildschirm Grab via "grab" geht noch nicht: unkown stb
-
Ab und zu beim normalen TV gucken kein Ton, genauso wie beim Gui-Restart oder Box Reboot
dann muss man umschalten, das ton kommt.
Ton ist generell um einiges leiser als bei der Dm920
(Muss Onkyo Verstärker von Pegel 21 (DM920) auf 31 (DMOne) aufdrehen, um selbe Lautstärke zu haben.
-
HBBTV macht endlich Spass. Alles sehr schnell geladen.
Im Bereich "Audio" gab es tatsächlich die umfangreichsten Änderungen. Dass da noch Probleme auftauchen haben war fast zu erwarten.
Wir haben das auf jeden Fall auf dem Schirm!
Bitte auch mal hier schauen ,es gibt einige Filme wo dann sowas raus kommt ,da steht eine utopische Laufzeit und nix startet es bleibt einfach stehen und schwarz.
Das wollte ich mal mit der one abspielen von der Platte meiner 920 uhd .
Auf der 920 uhd geht die Videodatei richtig.
Allgemein
ID : 1 (0x1)
Vollständiger Name : \\DM920\Harddisk\verschiedenes\filme\Die Mumie 3 - Das Grabmal des Drachenkaisers.m2ts
Format : BDAV
Format/Info : Blu-ray Video
Dateigröße : 16,3 GiB
Dauer : 1 h 51 min
Modus der Gesamtbitrate : variabel
Gesamte Bitrate : 20,9 Mb/s
maximale Gesamtbitrate : 35,5 Mb/s
Video
ID : 4113 (0x1011)
Menü-ID : 1 (0x1)
Format : AVC
Format/Info : Advanced Video Codec
Format-Profil : High@L4.1
Format-Einstellungen : CABAC / 4 Ref Frames
Format-Einstellungen für CABAC : Ja
Format-Einstellungen für RefFrames : 4 frames
Format_Settings_GOP : M=3, N=12
Codec-ID : 27
Dauer : 1 h 51 min
Bitraten-Modus : variabel
Bitrate : 18,7 Mb/s
maximale Bitrate : 29,0 Mb/s
Breite : 1 920 Pixel
Höhe : 1 080 Pixel
Bildseitenverhältnis : 16:9
Bildwiederholungsrate : 23,976 (24000/1001) FPS
ColorSpace : YUV
ChromaSubsampling/String : 4:2:0
BitDepth/String : 8 bits
Scantyp : progressiv
Bits/(Pixel*Frame) : 0.375
Stream-Größe : 14,6 GiB (89%)
colour_range : Limited
colour_primaries : BT.709
transfer_characteristics : BT.709
matrix_coefficients : BT.709
Audio #1
ID : 4352 (0x1100)
Menü-ID : 1 (0x1)
Format : AC-3
Format/Info : Audio Coding 3
Format_Commercial_IfAny : Dolby Digital
Codec-ID : 129
Dauer : 1 h 51 min
Bitraten-Modus : konstant
Bitrate : 640 kb/s
Kanäle : 6 Kanäle
Channel layout : L R C LFE Ls Rs
Samplingrate : 48,0 kHz
Bildwiederholungsrate : 31,250 FPS (1536 SPF)
BitDepth/String : 16 bits
Stream-Größe : 511 MiB (3%)
Sprache : Deutsch
ServiceKind/String : Complete Main
Audio #2
ID : 4353 (0x1101)
Menü-ID : 1 (0x1)
Format : DTS
Format/Info : Digital Theater Systems
Codec-ID : 130
Dauer : 1 h 51 min
Bitraten-Modus : konstant
Bitrate : 768 kb/s
Kanäle : 6 Kanäle
Channel layout : C L R Ls Rs LFE
Samplingrate : 48,0 kHz
Bildwiederholungsrate : 93,750 FPS (512 SPF)
BitDepth/String : 24 bits
Stream-Größe : 613 MiB (4%)
Sprache : Deutsch
Text
ID : 4608 (0x1200)
Menü-ID : 1 (0x1)
Format : PGS
Codec-ID : 144
Sprache : Deutsch
kannst mal den GL2 Benchmark mit der Option glmark2-es2 –off-screen testen, wie kommen die auf so Wahnsinnswerte für Odroid N2 (Hardware ziemlich mit der One identisch, ja OK mehr RAM 4GB bei N2), kann sein dass die One noch keine volle Pulle läuft
root@dreamone:~# glmark2-es2-dreambox off-screen
=======================================================
glmark2 2017.07
=======================================================
OpenGL Information
GL_VENDOR: ARM
GL_RENDERER: Mali-G52
GL_VERSION: OpenGL ES 3.2 git.c8adbf9.122c9daed32dbba4b3056f41a2f23c58
=======================================================
[build] use-vbo=false: FPS: 50 FrameTime: 20.000 ms
[build] use-vbo=true: FPS: 50 FrameTime: 20.000 ms
[texture] texture-filter=nearest: FPS: 50 FrameTime: 20.000 ms
[texture] texture-filter=linear: FPS: 50 FrameTime: 20.000 ms
[texture] texture-filter=mipmap: FPS: 50 FrameTime: 20.000 ms
[shading] shading=gouraud: FPS: 50 FrameTime: 20.000 ms
[shading] shading=blinn-phong-inf: FPS: 50 FrameTime: 20.000 ms
[shading] shading=phong: FPS: 50 FrameTime: 20.000 ms
[shading] shading=cel: FPS: 50 FrameTime: 20.000 ms
[bump] bump-render=high-poly: FPS: 50 FrameTime: 20.000 ms
[bump] bump-render=normals: FPS: 50 FrameTime: 20.000 ms
[bump] bump-render=height: FPS: 50 FrameTime: 20.000 ms
[effect2d] kernel=0,1,0;1,-4,1;0,1,0;: FPS: 50 FrameTime: 20.000 ms
[effect2d] kernel=1,1,1,1,1;1,1,1,1,1;1,1,1,1,1;: FPS: 50 FrameTime: 20.000 ms
[pulsar] light=false:quads=5:texture=false: FPS: 50 FrameTime: 20.000 ms
[desktop] blur-radius=5:effect=blur:passes=1:separable=true:windows=4: FPS: 49 FrameTime: 20.408 ms
[desktop] effect=shadow:windows=4: FPS: 50 FrameTime: 20.000 ms
[buffer] columns=200:interleave=false:update-dispersion=0.9:update-fraction=0.5:update-method=map: FPS: 28 FrameTime: 35
.714 ms
[buffer] columns=200:interleave=false:update-dispersion=0.9:update-fraction=0.5:update-method=subdata: FPS: 31 FrameTime
: 32.258 ms
[buffer] columns=200:interleave=true:update-dispersion=0.9:update-fraction=0.5:update-method=map: FPS: 49 FrameTime: 20.
408 ms
[ideas] speed=duration: FPS: 50 FrameTime: 20.000 ms
[jellyfish] <default>: FPS: 50 FrameTime: 20.000 ms
[terrain] <default>: FPS: 38 FrameTime: 26.316 ms
[shadow] <default>: FPS: 50 FrameTime: 20.000 ms
[refract] <default>: FPS: 45 FrameTime: 22.222 ms
[conditionals] fragment-steps=0:vertex-steps=0: FPS: 50 FrameTime: 20.000 ms
[conditionals] fragment-steps=5:vertex-steps=0: FPS: 50 FrameTime: 20.000 ms
[conditionals] fragment-steps=0:vertex-steps=5: FPS: 50 FrameTime: 20.000 ms
[function] fragment-complexity=low:fragment-steps=5: FPS: 50 FrameTime: 20.000 ms
[function] fragment-complexity=medium:fragment-steps=5: FPS: 50 FrameTime: 20.000 ms
[loop] fragment-loop=false:fragment-steps=5:vertex-steps=5: FPS: 50 FrameTime: 20.000 ms
[loop] fragment-steps=5:fragment-uniform=false:vertex-steps=5: FPS: 50 FrameTime: 20.000 ms
[loop] fragment-steps=5:fragment-uniform=true:vertex-steps=5: FPS: 50 FrameTime: 20.000 ms
=======================================================
glmark2 Score: 48
=======================================================
root@dreamone:~#
Alles anzeigen
Sieht ja ähnlich aus wie bei mir.
Bei Odroid-N2 liegt der score bei ca. 300, da stimmt also noch was nicht.
p7zip Benchmark
dreambox ONE
root@dreamone:~# 7za b
7-Zip (a) [64] 16.02 : Copyright (c) 1999-2016 Igor Pavlov : 2016-05-21
p7zip Version 16.02 (locale=C,Utf16=off,HugeFiles=on,64 bits,6 CPUs LE)
LE
CPU Freq: 1684 1695 1695 1695 1695 1695 1694 1694 1695
RAM size: 1988 MB, # CPU hardware threads: 6
RAM usage: 1323 MB, # Benchmark threads: 6
Compressing | Decompressing
Dict Speed Usage R/U Rating | Speed Usage R/U Rating
KiB/s % MIPS MIPS | KiB/s % MIPS MIPS
22: 5017 533 916 4881 | 108058 538 1712 9215
23: 4932 549 915 5026 | 104889 536 1694 9076
24: 4766 558 918 5125 | 102551 537 1676 9001
Killed
Bei 25: bricht es ab...
DM900
[16:38 root@dm900 ~] > 7za b
7-Zip (a) [32] 16.02 : Copyright (c) 1999-2016 Igor Pavlov : 2016-05-21
p7zip Version 16.02 (locale=de_DE@euro,Utf16=on,HugeFiles=on,32 bits,2 CPUs LE)
LE
CPU Freq: 1688 1697 1697 1698 1696 1697 1700 1697 1697
RAM size: 999 MB, # CPU hardware threads: 2
RAM usage: 441 MB, # Benchmark threads: 2
Compressing | Decompressing
Dict Speed Usage R/U Rating | Speed Usage R/U Rating
KiB/s % MIPS MIPS | KiB/s % MIPS MIPS
22: 1512 175 841 1471 | 34943 192 1552 2983
23: 1425 174 833 1453 | 33526 191 1519 2902
24: 1389 180 830 1494 | 32494 191 1494 2853
25: 1351 181 854 1543 | 31005 190 1449 2760
---------------------------------- | ------------------------------
Avr: 178 839 1490 | 191 1504 2874
Tot: 184 1171 2182
Der Load Avg von htop scheint 'real' zu sein.
gruß pclin
Alles halb so wild, kommt Zeit kommt Rat...
Im groben und ganzen war der Tag heute mit der Box ganz zufriedenstellend.
Nur die Kante hinten an der Box find ich aktuell am schlimmsten, das Sat-Kabel bekommt
man ja nur mit Fluchen drauf gedreht. Oder man muss sich einen Chinesen mit kleinen Finger
irgendwo besorgen
Völlig erstaunlich ist die IR-FB.
Egal ob Oben, Unten, nach vorne oder hinten, mann hat fast schon den Eindruck das wäre BT, so gut kommt das Signal an der Box (auch DM9x0) an.
Auch die Reichweite ist Super.
Fazit:
Um vieles besser als die RC10,
Nur an die Anordnung der Tasten muss man sich gewöhnen.
Da ist die RC10 besser.
gruß pclin
Alles anzeigenAlles halb so wild, kommt Zeit kommt Rat...
Im groben und ganzen war der Tag heute mit der Box ganz zufriedenstellend.
Nur die Kante hinten an der Box find ich aktuell am schlimmsten, das Sat-Kabel bekommt
man ja nur mit Fluchen drauf gedreht. Oder man muss sich einen Chinesen mit kleinen Finger
irgendwo besorgen
Ja das stimmt aber selbst mit kleinen Fingern geht es z.B. nicht einen USB Fit Stick wieder heraus zubekommen, ohne was anderes abzustecken.
Für SAT verwende ich F-Schnellverbinder.
gruß pclin
Alles anzeigenAlles halb so wild, kommt Zeit kommt Rat...
Im groben und ganzen war der Tag heute mit der Box ganz zufriedenstellend.
Nur die Kante hinten an der Box find ich aktuell am schlimmsten, das Sat-Kabel bekommt
man ja nur mit Fluchen drauf gedreht. Oder man muss sich einen Chinesen mit kleinen Finger
irgendwo besorgen
Einfach einen F-Quick Schnellverbinder kaufen und dann hast damit keine Probleme
compilieren auf der Box geht jetzt auch, ist SUPER schnell.
Mit das erste was ich compiliert habe ist dvb-apps, ist im OE2.6 Blacklisted
root@dreamone:/media/hdd/comp/dvb-apps# szap
usage: szap -q
list known channels
szap [options] {-n channel-number|channel_name}
zap to channel via number or full name (case insensitive)
-a number : use given adapter (default 0)
-f number : use given frontend (default 0)
-d number : use given demux (default 0)
-c file : read channels list from 'file'
-b : enable Audio Bypass (default no)
-x : exit after tuning
-H : human readable output
-r : set up /dev/dvb/adapterX/dvr0 for TS recording
-l lnb-type (DVB-S Only) (use -l help to print types) or
-l low[,high[,switch]] in Mhz
-i : run interactively, allowing you to type in channel names
-p : add pat and pmt to TS recording (implies -r)
or -n numbers for zapping
gruß pclin
tvheadend_4.3
root@dreamone:/media/hdd/comp/tvheadend/build.linux# tvheadend -v
tvheadend: version 4.3-1792~g466a01431
Geht auch nicht im OE2.6 zubauen, weil dvb-apps Blacklisted ist
root@dreamone:/media/hdd/comp/tvheadend/build.linux# tvheadend --help
Usage: tvheadend [OPTIONS]
Generic options
-h, --help Show this page
-v, --version Show version information
Service configuration
-c, --config Alternate configuration path
-B, --nobackup Don't backup configuration tree at upgrade
-f, --fork Fork and run as daemon
-u, --user Run as user
-g, --group Run as group
-p, --pid Alternate PID path
-C, --firstrun If no user account exists then create one with
no username and no password. Use with care as
it will allow world-wide administrative access
to your Tvheadend installation until you create or edit
the access control from within the Tvheadend web interface.
-U, --dbus Enable DBus
-e, --dbus_session DBus - use the session message bus instead of the system one
-a, --adapters Only use specified DVB adapters (comma-separated, -1 = none)
--satip_bindaddr Specify bind address for SAT>IP server
--satip_rtsp SAT>IP RTSP port number for server
(default: -1 = disable, 0 = webconfig, standard port is 554)
--nosatip Disable SAT>IP client
--satip_xml URL with the SAT>IP server XML location
Server connectivity
-6, --ipv6 Listen on IPv6
-b, --bindaddr Specify bind address
--http_port Specify alternative http port
--http_root Specify alternative http webroot
--htsp_port Specify alternative htsp port
--htsp_port2 Specify extra htsp port
--useragent Specify User-Agent header for the http client
--xspf Use XSPF playlist instead of M3U
Debug options
-d, --stderr Enable debug on stderr
-n, --nostderr Disable debug on stderr
-s, --syslog Enable debug to syslog
-S, --nosyslog Disable syslog (all messages)
-l, --logfile Enable debug to file
--debug Enable debug subsystems
--trace Enable trace subsystems
--subsystems List subsystems
--fileline Add file and line numbers to debug
--threadid Add the thread ID to debug
--libav More verbose libav log
--uidebug Enable web UI debug (non-minified JS)
-A, --abort Immediately abort
-D, --dump Enable coredumps for daemon
--noacl Disable all access control checks
--nobat Disable DVB bouquets
-j, --join Subscribe to a service permanently
Testing options
--tsfile_tuners Number of tsfile tuners
--tsfile tsfile input (mux file)
--tprofile Gather timing statistics for the code
--thrdebug Thread debugging
For more information please visit the Tvheadend website:
Compiler:
Using C compiler: cc
Using LD flags: -ldvbcsa
Build for arch: aarch64
Binaries:
Using PYTHON: python
Using GZIP: gzip
Using BZIP2: bzip2
Options:
pie yes
ccdebug no
cardclient yes
cwc yes
cccam yes
capmt yes
constcw yes
linuxdvb yes
satip_server yes
satip_client yes
hdhomerun_client yes
hdhomerun_static yes
iptv yes
tsfile yes
dvbscan yes
timeshift yes
trace yes
avahi no
zlib yes
libav yes
ffmpeg_static no
libx264 no
libx264_static no
libx265 yes
libx265_static no
libvpx no
libvpx_static no
libtheora yes
libtheora_static no
libvorbis yes
libvorbis_static no
libfdkaac no
libfdkaac_static no
libopus no
libopus_static no
nvenc no
vaapi no
mmal no
omx no
inotify yes
epoll yes
pcre no
pcre2 no
uriparser no
ccache no
tvhcsa yes
bundle no
pngquant no
kqueue no
dbus_1 yes
android no
gtimer_check no
slow_memoryinfo no
libsystemd_daemon yes
pcloud_cache yes
ddci yes
cclang_threadsan no
gperftools no
execinfo yes
W_unused_result yes
f_stack_protector yes
f_stack_protector_strong yes
f_stack_check yes
f_PIE yes
fdatasync yes
getloadavg yes
atomic32 yes
atomic64 yes
atomic_time_t yes
atomic_ptr yes
bitops64 yes
lockowner yes
qsort_r yes
stime yes
gmtoff yes
recvmmsg yes
sendmmsg yes
ifnames yes
py_gzip yes
bin_pkg_config yes
bin_xgettext yes
bin_msgmerge yes
bin_gzip yes
bin_bzip2 yes
ssl yes
linuxdvbapi yes
linuxdvb_ca yes
upnp yes
inotify_h yes
inotify_init1 yes
dvbcsa yes
epoll_create1 yes
mpegts yes
mpegts_dvb yes
Packages:
openssl 1.0.2n
zlib 1.2.11
libavfilter 7.40.101
libswresample 3.3.100
libswscale 5.3.100
libavformat 58.20.100
libavcodec 58.35.100
libavutil 56.22.100
dbus-1 1.10.14
libsystemd 232
Installation paths:
Prefix: /usr
Binaries: ${prefix}/bin
Libraries: ${prefix}/lib
Data files: ${prefix}/share
Man pages: ${datadir}/man
Final Binary:
/media/hdd/comp/tvheadend/build.linux/tvheadend
Tvheadend Data Directory:
/usr/share/tvheadend
gruß pclin
Meine Aussage bezüglich Audio aus Post #1 bezog sich auf S/PDIF (downmix an).
Über HDMI spielt das alles (mit und ohne downmix).
gruß pclin
Wie sieht es mit der Bluetooth Funktionalität aus?
1. Kann man einen BT Kopfhörer koppeln und Audio über BT ausgeben?
2. Ist eine gleichzeitige Ausgabe über BT und den optischen Ausgang möglich?
3. Ist der Ton synchron zum Bild.
4. Werden aptx oder aptx-HD unterstützt?
Vielen Dank?
zu 1. nein geht noch nicht ,es fehlen noch sehr viel Kernelmodule und daher kann man einiges noch nicht testen .
zu 2. TV Ton über BT ging noch nie und kann wie gesagt auch noch garnicht getestet werden da es dafür noch nix gibt.
Nur mal als Verdeutlichung
Bild 1 ist OE2.6 auf der One (da gibt es 9 Kernelmodule)
Bild 2 ist OE2.5 auf der 920 uhd (da sind es 1021)
Also ihr seht da fehlt noch eine Menge und daher kann man vieles auch noch garnicht richtig testen sondern erst wenn Dream das alles mal frei gibt auf ihrem Feed.
Naja Mal schauen was man davon überhaupt noch für das OE2.6 umsetzt. Oder für später aufschiebt.
golang-plaincast
Verbindung wird aufgebaut, spielt aber nichts ab.
gruß pclin
Bis jetzt erst ein GS und fast keine Spinner.
Beim Neustarten ging es bisher 2 mal nicht ohne Power Button zu verwenden.
Einmal dann keinen Zugriff FTP über Wlan.
DHCP war dann aus keine IP, auch manuell eingestellt ging dann nichts.
Erst nach reboot wieder IO.
Verwendet man Ton über S/PDIF gibt es beim Start fürchterliche Geräusche.
gruß pclin