As far as I can tell, you already updated your loader. So don't waste your time trying again.
If you want to update your rescue loader again later, do it from a normal boot (i.e. when enigma2 is running).
As far as I can tell, you already updated your loader. So don't waste your time trying again.
If you want to update your rescue loader again later, do it from a normal boot (i.e. when enigma2 is running).
As far as I can tell, you already updated your loader. So don't waste your time trying again.
If you want to update your rescue loader again later, do it from a normal boot (i.e. when enigma2 is running).
OK,what can I do if enigma 2 is not running?
telnet dies hard (c) Bruce Willis
In recovery mode
Remounting '/dev/mmcblk0p3' to '/data'
Downloading 'http://dreamboxupdate.com/download/recovery/dm900/release/recovery.sig'
Copying 'recovery' from local storage
Verifying signature of 'recovery'
gpgv: Signature made Wed Dec 21 02:02:08 2016 UTC using RSA key ID 7DA27561
gpgv: Good signature from "Dreambox DM900 Recovery <dm900@recovery.dreambox.de>"
Unmounting '/data'
Running './recovery'
Options '-v -b -r'
Mounting '/dev/mmcblk0p3' to '/data'
Downloading 'http://dreamboxupdate.com/download/recovery/dm900/release/dreambox-image-dm900.tar.xz.sig'
Copying 'dreambox-image-dm900.tar.xz' from local storage
Verifying signature of 'dreambox-image-dm900.tar.xz'
gpgv: Signature made Sat Dec 10 00:27:46 2016 UTC using RSA key ID 7DA27561
gpgv: Good signature from "Dreambox DM900 Recovery <dm900@recovery.dreambox.de>"
Mounting '/dev/mmcblk0p2' to '/mnt'
sed: /mnt/etc/shadow: No such file or directory
Unmounting '/mnt'
Unmounting '/data'
Fatal: Failed to execute './recovery'
When I try firmware upload
[*] Remounting '/dev/mmcblk0p3' to '/data'[*] Mounting '/dev/mmcblk0p2' to '/mnt'sed: /mnt/etc/shadow: No such file or directory[*] Unmounting '/mnt'
How I can load the image?
remove the settings backup/restore ticks
In case when image not run and telnet not work .How I can update the image via serial?
at me the same case until yesterday all ok this morning Dreambox no internet(lan) connection to router, other equipment okay, help
Why every time when I backup or upload new image appear this warning? Warning: Could not read CA!
Warning: Please consider updating your rescue loader!
Then you maybe should consider to follow the given advice
Then you maybe should consider to follow the given advice
gutemine,once and again I update the loader ...
what version does it show when it is loaded ?
Flash latest OE2.5 Experimental, then follow Bruce Willis' advice and enter
update-rescue in telnet.
what version does it show when it is loaded ?
Flash latest OE2.5 Experimental, then follow Bruce Willis' advice and enter
update-rescue in telnet.
Version#103. Sorry ,I do not understand about B.Willis..
yes, then you are up to date as obi suggested and you don't need to do an update-rescue via telnet anymore.
Hi mate...i've read all above. I've new box with old BL. And of course i want to update it to new version 103. Could any one tell me how step by step to do it?
As my understanding :
1. After running the current image, open telnet session
2. do with command : update-rescue
am i correct? need advise. Thx mate
Here are just a call in my dreambox replaced because is dead network card, disaster, despair and disappointment after three days of work
Thax all,sorry Dreambox USB port only for bootlog use?
There is one service port which is the small USB with the description "Service". Other USB ports exist for some Dreamboxes only.
There is one service port which is the small USB with the description "Service". Other USB ports exist for some Dreamboxes only.
Yes, shure service USB for bootlog only?
well it is also a console device, which means you can logon via this port also.
well it is also a console device, which means you can logon via this port also.
Logon and flash?