memc f1182000.memc-ddr: registered
[    0.097714] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.098626] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
[    0.193881] console [ttyS0] enabled
[    0.195117] loop: module loaded
[    0.195764] ahci brcmstb-ahci.0: can't get clock
[    0.196383] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[    0.207236] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    0.208233] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part 
[    0.210674] scsi0 : ahci_platform
[    0.211302] scsi1 : ahci_platform
[    0.211807] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
[    0.212725] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
[    0.214140] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[    0.214921] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[    0.216046] m25p80 spi32766.0: found mx25l25635e, expected m25p80
[    0.216763] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address
[    0.217494] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
[    0.218134] 5 ofpart partitions found on MTD device spi32766.0
[    0.218810] Creating 5 MTD partitions on "spi32766.0":
[    0.219408] 0x000000000000-0x000000200000 : "flash0.bolt"
[    0.220505] 0x000000200000-0x000000220000 : "flash0.nvram"
[    0.221536] 0x000000220000-0x000000240000 : "flash0.devtree"
[    0.222593] 0x000000240000-0x000001000000 : "flash0.recovery"
[    0.223657] 0x000000000000-0x000002000000 : "flash0"
[    0.224949] libphy: Fixed MDIO Bus: probed
[    0.225561] tun: Universal TUN/TAP device driver, 1.6
[    0.226142] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.227180] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[    0.241221] libphy: bcmgenet MII bus: probed
[    0.262106] xhci-brcm: xHCI BRCM driver
[    0.262633] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    0.263310] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[    0.264415] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
[    0.265563] hub 1-0:1.0: USB hub found
[    0.266017] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    0.266944] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    0.267612] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[    0.268892] hub 2-0:1.0: USB hub found
[    0.269352] hub 2-0:1.0: 2 ports detected
[    0.270119] ehci-brcm: EHCI BRCM driver
[    0.270637] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[    0.271302] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[    0.282308] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
[    0.288226] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[    0.289298] hub 3-0:1.0: USB hub found
[    0.289748] hub 3-0:1.0: 1 port detected
[    0.290401] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[    0.291060] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[    0.302046] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
[    0.308223] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[    0.309276] hub 4-0:1.0: USB hub found
[    0.309724] hub 4-0:1.0: 1 port detected
[    0.310424] ohci-brcm: OHCI BRCM driver
[    0.310926] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[    0.311595] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
[    0.312517] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
[    0.368610] hub 5-0:1.0: USB hub found
[    0.369061] hub 5-0:1.0: 1 port detected
[    0.369735] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[    0.370409] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
[    0.371327] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
[    0.426581] hub 6-0:1.0: USB hub found
[    0.427030] hub 6-0:1.0: 1 port detected
[    0.427741] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.428500] ehci-pci: EHCI PCI platform driver
[    0.429047] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.429763] ohci-pci: OHCI PCI platform driver
[    0.430395] usbcore: registered new interface driver usb-storage
[    0.431233] i2c /dev entries driver
[    0.431941] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[    0.432918] usbcore: registered new interface driver btusb
[    0.433611] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    0.434400] sdhci: Secure Digital Host Controller Interface driver
[    0.435109] sdhci: Copyright(c) Pierre Ossman
[    0.435619] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.437377] mmc0: no vqmmc regulator found
[    0.437851] mmc0: no vmmc regulator found
[    0.468229] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
[    0.470134] mmc1: no vqmmc regulator found
[    0.470614] mmc1: no vmmc regulator found
[    0.481235] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.483889] ata1.00: ATA-9: SAMSUNG MZ7LN256HCHP-000H1, EMT02H0Q, max UDMA/133
[    0.484732] ata1.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    0.490205] ata1.00: configured for UDMA/133
[    0.492940] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG MZ7LN256 EMT0 PQ: 0 ANSI: 5
[    0.494338] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[    0.496418] sd 0:0:0:0: [sda] Write Protect is off
[    0.497024] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.501257] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[    0.501530]  sda: sda1 sda2
[    0.502591] hidraw: raw HID events driver (C) Jiri Kosina
[    0.503297] usbcore: registered new interface driver usbhid
[    0.503936] usbhid: USB HID core driver
[    0.504673] TCP: cubic registered
[    0.505109] NET: Registered protocol family 10
[    0.506168] NET: Registered protocol family 17
[    0.506659] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.507492] Bluetooth: RFCOMM TTY layer initialized
[    0.508071] Bluetooth: RFCOMM socket layer initialized
[    0.508673] Bluetooth: RFCOMM ver 1.11
[    0.509105] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    0.509721] Bluetooth: BNEP filters: protocol multicast
[    0.510330] Bluetooth: BNEP socket layer initialized
[    0.510902] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    0.511590] Bluetooth: HIDP socket layer initialized
[    0.512205] l2tp_core: L2TP core driver, V2.0
[    0.512746] Key type dns_resolver registered
[    0.513298] Registering SWP/SWPB emulation handler
[    0.514108] regulator-dummy: disabling
[    0.514745] ALSA device list:
[    0.515090]   No soundcards found.
[    0.604232] ata2: SATA link down (SStatus 0 SControl 300)
[    0.606302] Waiting for root device /dev/mmcblk0p2...
[    0.734689] mmc0: new high speed SDXC card at address aaaa
[    0.735523] mmcblk1: mmc0:aaaa SL64G 59.4 GiB 
[    0.738205]  mmcblk1: p1
[    0.806863] mmc1: BKOPS_EN bit is not set
[    0.813553] mmc1: new high speed MMC card at address 0001
[    0.814363] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB 
[    0.814972] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
[    0.815747] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
[    0.816508] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
[    0.820638]  mmcblk0: p1 p2 p3
[    0.823564]  mmcblk0boot1: unknown partition table
[    0.824591]  mmcblk0boot0: unknown partition table
[    0.914785] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    0.915748] VFS: Mounted root (ext4 filesystem) readonly on device 179:10.
[    0.918296] devtmpfs: mounted
[    0.918740] Freeing unused kernel memory: 244K (c073e000 - c077b000)
[    0.936033] request_module: runaway loop modprobe binfmt-464c
[    0.938741] Starting init: /sbin/init exists but couldn't execute it (error -8)
[    0.945729] request_module: runaway loop modprobe binfmt-464c
[    0.948339] Starting init: /bin/sh exists but couldn't execute it (error -8)
[    0.949151] Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[    0.950655] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14-1.15-dm900 #63
[    0.951455] [<c0014e30>] (unwind_backtrace) from [<c0011264>] (show_stack+0x10/0x14)
[    0.952349] [<c0011264>] (show_stack) from [<c059b044>] (dump_stack+0x78/0x88)
[    0.953181] [<c059b044>] (dump_stack) from [<c059a4d8>] (panic+0xa0/0x1ec)
[    0.953974] [<c059a4d8>] (panic) from [<c05982d0>] (cpu_die+0x0/0x90)
[    0.954715] [<c05982d0>] (cpu_die) from [<00000000>] (  (null))
[    0.955398] CPU0: stopping
[    0.955714] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14-1.15-dm900 #63
[    0.956499] [<c0014e30>] (unwind_backtrace) from [<c0011264>] (show_stack+0x10/0x14)
[    0.957389] [<c0011264>] (show_stack) from [<c059b044>] (dump_stack+0x78/0x88)
[    0.958220] [<c059b044>] (dump_stack) from [<c0014054>] (handle_IPI+0x164/0x198)
[    0.959070] [<c0014054>] (handle_IPI) from [<c00085d0>] (gic_handle_irq+0x58/0x5c)
[    0.959941] [<c00085d0>] (gic_handle_irq) from [<c0011d40>] (__irq_svc+0x40/0x50)
[    0.960798] Exception stack(0xc077df60 to 0xc077dfa8)
[    0.961381] df60: ffffffed 0d847000 c07854c8 00000000 c077c030 c0784420 c078449c c05a288c
[    0.962318] df80: c07b0c63 c07b0c63 c077c000 00000000 c078c040 c077dfa8 c000efb0 c000efa8
[    0.963253] dfa0: 60000113 ffffffff
[    0.963659] [<c0011d40>] (__irq_svc) from [<c000efa8>] (arch_cpu_idle+0x2c/0x38)
[    0.964512] [<c000efa8>] (arch_cpu_idle) from [<c00637cc>] (cpu_startup_entry+0x100/0x144)
[    0.965463] [<c00637cc>] (cpu_startup_entry) from [<c073ebf0>] (start_kernel+0x414/0x420)